Measurement evidence for Frigidaire Gallery GRFN2023AF

Value used by ExactFit

30 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery GRFN2023AF Product Specifications Sheet
assets.skulytics.io · Product Specifications Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width 30"

Why this value was used

Width 30"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

67.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery GRFN2023AF Product Specifications Sheet
assets.skulytics.io · Product Specifications Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height Without Hinge 67 7/8"

Why this value was used

Height Without Hinge 67 7/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.6875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery GRFN2023AF Product Specifications Sheet
assets.skulytics.io · Product Specifications Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height With Hinge 68 11/16"

Why this value was used

Height With Hinge 68 11/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery GRFN2023AF Product Specifications Sheet
assets.skulytics.io · Product Specifications Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth of Cabinet 26 3/8"

Why this value was used

Depth of Cabinet 26 3/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.0625 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery GRFN2023AF Product Specifications Sheet
assets.skulytics.io · Product Specifications Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door 31 1/16"

Why this value was used

Depth With Door 31 1/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

33.3125 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery GRFN2023AF Product Specifications Sheet
assets.skulytics.io · Product Specifications Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door and Handle 33 5/16"

Why this value was used

Depth With Door and Handle 33 5/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

42 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery GRFN2023AF Product Specifications Sheet
assets.skulytics.io · Product Specifications Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door 90° Open 42"

Why this value was used

Depth With Door 90° Open 42"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

33.14 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 30.0 + (2 * 1.57) = 33.14 inches

Confidence label: medium.

Primary evidence

Frigidaire Gallery GRFN2023AF Product Specifications Sheet
assets.skulytics.io · Product Specifications Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-04

Derived minimum opening from validated overall width 30.0 in and exact-model side clearance 1.57 in per side. Side evidence: Sides | 1.57 in. (40 mm) | Back

Why this value was used

Derived minimum opening from validated overall width 30.0 in and exact-model side clearance 1.57 in per side. Side evidence: Sides | 1.57 in. (40 mm) | Back Calculation or inference: 30.0 + (2 * 1.57) = 33.14 inches.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

72.2275 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Frigidaire Gallery GRFN2023AF Complete Owner's Guide
assets.skulytics.io · Complete Owner's Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 68.6875 in plus documented top clearance 3.54 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 68.6875 in plus documented top clearance 3.54 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.345 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Frigidaire Gallery GRFN2023AF Complete Owner's Guide
assets.skulytics.io · Complete Owner's Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 26.375 in plus documented rear clearance 1.97 in.

Why this value was used

Minimum opening depth derived from case-only depth 26.375 in plus documented rear clearance 1.97 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1.57 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Frigidaire Gallery GRFN2023AF Complete Owner's Guide
assets.skulytics.io · Complete Owner's Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-05

Sides | 1.57 in. (40 mm) | Back

Why this value was used

Sides | 1.57 in. (40 mm) | Back

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1.57 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Frigidaire Gallery GRFN2023AF Complete Owner's Guide
assets.skulytics.io · Complete Owner's Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-05

Sides | 1.57 in. (40 mm) | Back

Why this value was used

Sides | 1.57 in. (40 mm) | Back

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.54 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Frigidaire Gallery GRFN2023AF Complete Owner's Guide
assets.skulytics.io · Complete Owner's Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-05

Back | 1.97 in. (50 mm) | Top 3.54 in. (90 mm)

Why this value was used

Back | 1.97 in. (50 mm) | Top 3.54 in. (90 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1.97 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Frigidaire Gallery GRFN2023AF Complete Owner's Guide
assets.skulytics.io · Complete Owner's Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-05

Back | 1.97 in. (50 mm) | Top 3.54 in. (90 mm)

Why this value was used

Back | 1.97 in. (50 mm) | Top 3.54 in. (90 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: hinge baseline = documented model-specific side installation clearance

Confidence label: medium.

Primary evidence

Frigidaire Gallery GRFN2023AF Complete Owner's Guide
assets.skulytics.io · Complete Owner's Guide
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-05

Exact-model manual documents 1.57 in side installation clearance. Its hinge-wall note is conditional and gives no separate numeric minimum; the documented side-clearance baseline is retained for the hinge-side field.

Why this value was used

A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.

Retained research value: 1.57 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.8125 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery GRFN2023AF Product Specifications Sheet
assets.skulytics.io · Product Specifications Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width of Cabinet 29 13/16"

Why this value was used

Width of Cabinet 29 13/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

1.57 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire Gallery GRFN2023AF Complete Owner's Guide
assets.skulytics.io · Complete Owner's Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-04

Sides | 1.57 in. (40 mm) | Back

Why this value was used

Sides | 1.57 in. (40 mm) | Back

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.