This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Single Door Refrigerator · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-09. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 32.875 in | ✓ Verified — retained secondary source | Frigidaire Gallery installation document — 106160758.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit32.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Gallery installation document — 106160758.pdf Width of Cabinet 32 7/8"Open original source ↗ Why this value was usedWidth of Cabinet 32 7/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 71.5 in | ✓ Verified — retained secondary source | Frigidaire Gallery installation document — 106160758.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit71.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Gallery installation document — 106160758.pdf Height Without Hinge 71 1/2"Open original source ↗ Why this value was usedHeight Without Hinge 71 1/2" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 72.5 in | ✓ Verified — retained secondary source | Frigidaire Gallery installation document — 106160758.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit72.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Gallery installation document — 106160758.pdf Height With Hinge 72 1/2"Open original source ↗ Why this value was usedHeight With Hinge 72 1/2" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24.625 in | ✓ Verified — retained secondary source | Frigidaire Gallery measurement source — frigidaire-gallery-refrigerator-33-in-189-ft3-with-crispseal-crisper-grey-grda1911af-10355903 www.rona.ca | Retained specification excerpt: Exact-model RONA specification: Depth (Less Door) 24.625 in. | |
Value used by ExactFit24.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Gallery measurement source — frigidaire-gallery-refrigerator-33-in-189-ft3-with-crispseal-crisper-grey-grda1911af-10355903 Exact-model RONA specification: Depth (Less Door) 24.625 in.Open original source ↗ Why this value was usedExact-model RONA specification: Depth (Less Door) 24.625 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 27 in | ✓ Verified — retained secondary source | Frigidaire Gallery installation document — 106160758.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit27 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Gallery installation document — 106160758.pdf Depth With Door 27"Open original source ↗ Why this value was usedDepth With Door 27" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 28.625 in | ✓ Verified — retained secondary source | Frigidaire Gallery measurement source — frigidaire-gallery-refrigerator-33-in-189-ft3-with-crispseal-crisper-grey-grda1911af-10355903 www.rona.ca | Retained specification excerpt: Exact-model RONA specification: Depth (Including Handles) 28.625 in. | |
Value used by ExactFit28.625 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Gallery measurement source — frigidaire-gallery-refrigerator-33-in-189-ft3-with-crispseal-crisper-grey-grda1911af-10355903 Exact-model RONA specification: Depth (Including Handles) 28.625 in.Open original source ↗ Why this value was usedExact-model RONA specification: Depth (Including Handles) 28.625 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 58.25 in | ✓ Verified — retained secondary source | Frigidaire Gallery installation document — 106160758.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit58.25 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Gallery installation document — 106160758.pdf Depth With Door 90° Open 58 1/4"Open original source ↗ Why this value was usedDepth With Door 90° Open 58 1/4" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 33 in | ✓ Conflicting sources — resolved | Frigidaire Gallery measurement source — 106160765.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit33 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Gallery measurement source — 106160765.pdf Manufacturer manual section 3.5, Minimum dimensions for Single Cabinet without Trim Kit: 33 in width.Open original source ↗ Why this value was usedManufacturer manual section 3.5, Minimum dimensions for Single Cabinet without Trim Kit: 33 in width. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 73.5 in | ✓ Verified — retained secondary source | Frigidaire Gallery measurement source — 106160765.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit73.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Gallery measurement source — 106160765.pdf Manufacturer manual section 3.5, Minimum dimensions for Single Cabinet without Trim Kit: 73.5 in height.Open original source ↗ Why this value was usedManufacturer manual section 3.5, Minimum dimensions for Single Cabinet without Trim Kit: 73.5 in height. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25.625 in | ✓ Verified — retained secondary source | Frigidaire Gallery measurement source — 106160765.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit25.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Gallery measurement source — 106160765.pdf Manufacturer manual section 3.5, Minimum dimensions for Single Cabinet without Trim Kit: 25.625 in minimum depth.Open original source ↗ Why this value was usedManufacturer manual section 3.5, Minimum dimensions for Single Cabinet without Trim Kit: 25.625 in minimum depth. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.1875 in | ✓ Verified — retained secondary source | Frigidaire Gallery installation document — 106160765.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit0.1875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Gallery installation document — 106160765.pdf • The appliance must be installed on a floor that is level and strong enough to support a fully loaded appliance. WARNING! This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / kitchenette • Pantry room • Basement • Enclosed garage • Other interior residential type environments WARNING! Allow the following clearances for ease of installation, proper air circulation, plumbing, and electrical connections: • Top 1" (25.4 mm) • Sides 3/16" (4.76 mm) • Back 1" (25.4 mm) 3.4 Cabinet leveling and door alignment Guidelines for final positioning of appliance: • All 4 corners of the cabinet must rest firmly on the floor. 3.5 Minimum dimensions for Single Cabinet without Trim Kit 33" 25.625" min 73.5" 3.6 Setting the anti-tip brackets The anti-tip brackets are located on the lower front corners of the cabinet. Lower the anti-tip brackets on each side 6 ENGLISHOpen original source ↗ Why this value was used• The appliance must be installed on a floor that is level and strong enough to support a fully loaded appliance. WARNING! This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / kitchenette • Pantry room • Basement • Enclosed garage • Other interior residential type environments WARNING! Allow the following clearances for ease of installation, proper air circulation, plumbing, and electrical connections: • Top 1" (25.4 mm) • Sides 3/16" (4.76 mm) • Back 1" (25.4 mm) 3.4 Cabinet leveling and door alignment Guidelines for final positioning of appliance: • All 4 corners of the cabinet must rest firmly on the floor. 3.5 Minimum dimensions for Single Cabinet without Trim Kit 33" 25.625" min 73.5" 3.6 Setting the anti-tip brackets The anti-tip brackets are located on the lower front corners of the cabinet. Lower the anti-tip brackets on each side 6 ENGLISH Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.1875 in | ✓ Verified — retained secondary source | Frigidaire Gallery installation document — 106160765.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit0.1875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Gallery installation document — 106160765.pdf • The appliance must be installed on a floor that is level and strong enough to support a fully loaded appliance. WARNING! This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / kitchenette • Pantry room • Basement • Enclosed garage • Other interior residential type environments WARNING! Allow the following clearances for ease of installation, proper air circulation, plumbing, and electrical connections: • Top 1" (25.4 mm) • Sides 3/16" (4.76 mm) • Back 1" (25.4 mm) 3.4 Cabinet leveling and door alignment Guidelines for final positioning of appliance: • All 4 corners of the cabinet must rest firmly on the floor. 3.5 Minimum dimensions for Single Cabinet without Trim Kit 33" 25.625" min 73.5" 3.6 Setting the anti-tip brackets The anti-tip brackets are located on the lower front corners of the cabinet. Lower the anti-tip brackets on each side 6 ENGLISHOpen original source ↗ Why this value was used• The appliance must be installed on a floor that is level and strong enough to support a fully loaded appliance. WARNING! This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / kitchenette • Pantry room • Basement • Enclosed garage • Other interior residential type environments WARNING! Allow the following clearances for ease of installation, proper air circulation, plumbing, and electrical connections: • Top 1" (25.4 mm) • Sides 3/16" (4.76 mm) • Back 1" (25.4 mm) 3.4 Cabinet leveling and door alignment Guidelines for final positioning of appliance: • All 4 corners of the cabinet must rest firmly on the floor. 3.5 Minimum dimensions for Single Cabinet without Trim Kit 33" 25.625" min 73.5" 3.6 Setting the anti-tip brackets The anti-tip brackets are located on the lower front corners of the cabinet. Lower the anti-tip brackets on each side 6 ENGLISH Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 1 in | ✓ Verified — retained secondary source | Frigidaire Gallery measurement source — 106160765.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Gallery measurement source — 106160765.pdf connections: | • Top 1" (25.4 mm) | • Sides 3/16" (4.76 mm) | deterministic pattern: installation_sidesOpen original source ↗ Why this value was usedconnections: | • Top 1" (25.4 mm) | • Sides 3/16" (4.76 mm) | deterministic pattern: installation_sides Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Verified — retained secondary source | Frigidaire Gallery installation document — 106160765.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Gallery installation document — 106160765.pdf • The appliance must be installed on a floor that is level and strong enough to support a fully loaded appliance. WARNING! This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / kitchenette • Pantry room • Basement • Enclosed garage • Other interior residential type environments WARNING! Allow the following clearances for ease of installation, proper air circulation, plumbing, and electrical connections: • Top 1" (25.4 mm) • Sides 3/16" (4.76 mm) • Back 1" (25.4 mm) 3.4 Cabinet leveling and door alignment Guidelines for final positioning of appliance: • All 4 corners of the cabinet must rest firmly on the floor. 3.5 Minimum dimensions for Single Cabinet without Trim Kit 33" 25.625" min 73.5" 3.6 Setting the anti-tip brackets The anti-tip brackets are located on the lower front corners of the cabinet. Lower the anti-tip brackets on each side 6 ENGLISHOpen original source ↗ Why this value was used• The appliance must be installed on a floor that is level and strong enough to support a fully loaded appliance. WARNING! This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / kitchenette • Pantry room • Basement • Enclosed garage • Other interior residential type environments WARNING! Allow the following clearances for ease of installation, proper air circulation, plumbing, and electrical connections: • Top 1" (25.4 mm) • Sides 3/16" (4.76 mm) • Back 1" (25.4 mm) 3.4 Cabinet leveling and door alignment Guidelines for final positioning of appliance: • All 4 corners of the cabinet must rest firmly on the floor. 3.5 Minimum dimensions for Single Cabinet without Trim Kit 33" 25.625" min 73.5" 3.6 Setting the anti-tip brackets The anti-tip brackets are located on the lower front corners of the cabinet. Lower the anti-tip brackets on each side 6 ENGLISH Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 32.875 in | ✓ Verified — retained secondary source | Frigidaire Gallery installation document — 106160758.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit32.875 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire Gallery installation document — 106160758.pdf Width of Cabinet 32 7/8"Open original source ↗ Why this value was usedWidth of Cabinet 32 7/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 33 in. Earlier retained values: 33.25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Manufacturer manual section 3.5, Minimum dimensions for Single Cabinet without Trim Kit: 33 in width.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: GRDA1911AF. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
6 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth with door, without handles; Depth with doors open at 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗www.rona.ca · Web source · secondary model/source
Model numbers covered: GRDA1911AF. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
2 displayed measurements supported: Depth without door; Depth with handle.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: GRDA1911AF. Publication/revision date: Not recorded. Reviewed: 2026-09-09.
7 displayed measurements supported: Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-09. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.