Measurement evidence for Frigidaire Gallery GRBN2012AF
This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-25. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502727.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502727.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502727.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502727.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502727.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502727.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502727.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Frigidaire Gallery measurement source — 103502730.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-09-09
Frigidaire Gallery installation-envelope calculation: case_width_in=29.8, side_ventilation_clearance_in=1.57; result=32.94 in. Product source: 103502727.pdf. Clearance source text: igerator drawers and freezer baskets, position the appliance where both can open fully. INSTALLATION CAUTION Do Not install the appliance where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the appliance. NOTE If you place your appliance with the door hinge side against a wall, you may have to allow additional space for the handle so you can open the door wider. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential-type environments WARNING Installation Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 1.57 in. (40 mm) Back 1.97 in. (50 mm) Top 3.54 in. (90 mm) CAUTION The sides of the refrigerator are warm surfaces. The warmth felt on the left and right sides of the fridge is normal for this cooling technology.
Frigidaire Gallery installation-envelope calculation: case_width_in=29.8, side_ventilation_clearance_in=1.57; result=32.94 in. Product source: 103502727.pdf. Clearance source text: igerator drawers and freezer baskets, position the appliance where both can open fully. INSTALLATION CAUTION Do Not install the appliance where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the appliance. NOTE If you place your appliance with the door hinge side against a wall, you may have to allow additional space for the handle so you can open the door wider. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential-type environments WARNING Installation Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 1.57 in. (40 mm) Back 1.97 in. (50 mm) Top 3.54 in. (90 mm) CAUTION The sides of the refrigerator are warm surfaces. The warmth felt on the left and right sides of the fridge is normal for this cooling technology. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in.
Other evidence found
33.14 in — superseded
Document 103502727.pdf + Document 103502730.pdf; page 8. Model scope: not separately recorded. Raw value: Derived minimum opening from validated overall width 30.0 in and exact-model side clearance 1.57 in per side. Side evidence: Sides | 1.57 in. (40 mm) | Back. The final reviewed registry supersedes this earlier audit value.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Frigidaire Gallery measurement source — 103502730.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-09-09
Frigidaire Gallery installation-envelope calculation: height_hinge_in=68.7, top_clearance_in=3.54; result=72.24 in. Product source: 103502727.pdf. Clearance source text: igerator drawers and freezer baskets, position the appliance where both can open fully. INSTALLATION CAUTION Do Not install the appliance where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the appliance. NOTE If you place your appliance with the door hinge side against a wall, you may have to allow additional space for the handle so you can open the door wider. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential-type environments WARNING Installation Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 1.57 in. (40 mm) Back 1.97 in. (50 mm) Top 3.54 in. (90 mm) CAUTION The sides of the refrigerator are warm surfaces. The warmth felt on the left and right sides of the fridge is normal for this cooling technology.
Frigidaire Gallery installation-envelope calculation: height_hinge_in=68.7, top_clearance_in=3.54; result=72.24 in. Product source: 103502727.pdf. Clearance source text: igerator drawers and freezer baskets, position the appliance where both can open fully. INSTALLATION CAUTION Do Not install the appliance where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the appliance. NOTE If you place your appliance with the door hinge side against a wall, you may have to allow additional space for the handle so you can open the door wider. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential-type environments WARNING Installation Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 1.57 in. (40 mm) Back 1.97 in. (50 mm) Top 3.54 in. (90 mm) CAUTION The sides of the refrigerator are warm surfaces. The warmth felt on the left and right sides of the fridge is normal for this cooling technology. Calculation or inference: height_hinge_in + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Frigidaire Gallery measurement source — 103502730.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-09-09
Frigidaire Gallery installation-envelope calculation: depth_case_only_in=26.4, rear_clearance_in=1.97; result=28.37 in. Product source: 103502727.pdf. Clearance source text: igerator drawers and freezer baskets, position the appliance where both can open fully. INSTALLATION CAUTION Do Not install the appliance where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the appliance. NOTE If you place your appliance with the door hinge side against a wall, you may have to allow additional space for the handle so you can open the door wider. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential-type environments WARNING Installation Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 1.57 in. (40 mm) Back 1.97 in. (50 mm) Top 3.54 in. (90 mm) CAUTION The sides of the refrigerator are warm surfaces. The warmth felt on the left and right sides of the fridge is normal for this cooling technology.
Frigidaire Gallery installation-envelope calculation: depth_case_only_in=26.4, rear_clearance_in=1.97; result=28.37 in. Product source: 103502727.pdf. Clearance source text: igerator drawers and freezer baskets, position the appliance where both can open fully. INSTALLATION CAUTION Do Not install the appliance where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the appliance. NOTE If you place your appliance with the door hinge side against a wall, you may have to allow additional space for the handle so you can open the door wider. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential-type environments WARNING Installation Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 1.57 in. (40 mm) Back 1.97 in. (50 mm) Top 3.54 in. (90 mm) CAUTION The sides of the refrigerator are warm surfaces. The warmth felt on the left and right sides of the fridge is normal for this cooling technology. Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502730.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-09-09
igerator drawers and freezer baskets, position the appliance where both can open fully. INSTALLATION CAUTION Do Not install the appliance where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the appliance. NOTE If you place your appliance with the door hinge side against a wall, you may have to allow additional space for the handle so you can open the door wider. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential-type environments WARNING Installation Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 1.57 in. (40 mm) Back 1.97 in. (50 mm) Top 3.54 in. (90 mm) CAUTION The sides of the refrigerator are warm surfaces. The warmth felt on the left and right sides of the fridge is normal for this cooling technology.
igerator drawers and freezer baskets, position the appliance where both can open fully. INSTALLATION CAUTION Do Not install the appliance where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the appliance. NOTE If you place your appliance with the door hinge side against a wall, you may have to allow additional space for the handle so you can open the door wider. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential-type environments WARNING Installation Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 1.57 in. (40 mm) Back 1.97 in. (50 mm) Top 3.54 in. (90 mm) CAUTION The sides of the refrigerator are warm surfaces. The warmth felt on the left and right sides of the fridge is normal for this cooling technology.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502730.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-09-09
igerator drawers and freezer baskets, position the appliance where both can open fully. INSTALLATION CAUTION Do Not install the appliance where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the appliance. NOTE If you place your appliance with the door hinge side against a wall, you may have to allow additional space for the handle so you can open the door wider. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential-type environments WARNING Installation Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 1.57 in. (40 mm) Back 1.97 in. (50 mm) Top 3.54 in. (90 mm) CAUTION The sides of the refrigerator are warm surfaces. The warmth felt on the left and right sides of the fridge is normal for this cooling technology.
igerator drawers and freezer baskets, position the appliance where both can open fully. INSTALLATION CAUTION Do Not install the appliance where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the appliance. NOTE If you place your appliance with the door hinge side against a wall, you may have to allow additional space for the handle so you can open the door wider. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential-type environments WARNING Installation Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 1.57 in. (40 mm) Back 1.97 in. (50 mm) Top 3.54 in. (90 mm) CAUTION The sides of the refrigerator are warm surfaces. The warmth felt on the left and right sides of the fridge is normal for this cooling technology.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502730.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-09-09
igerator drawers and freezer baskets, position the appliance where both can open fully. INSTALLATION CAUTION Do Not install the appliance where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the appliance. NOTE If you place your appliance with the door hinge side against a wall, you may have to allow additional space for the handle so you can open the door wider. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential-type environments WARNING Installation Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 1.57 in. (40 mm) Back 1.97 in. (50 mm) Top 3.54 in. (90 mm) CAUTION The sides of the refrigerator are warm surfaces. The warmth felt on the left and right sides of the fridge is normal for this cooling technology.
igerator drawers and freezer baskets, position the appliance where both can open fully. INSTALLATION CAUTION Do Not install the appliance where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the appliance. NOTE If you place your appliance with the door hinge side against a wall, you may have to allow additional space for the handle so you can open the door wider. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential-type environments WARNING Installation Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 1.57 in. (40 mm) Back 1.97 in. (50 mm) Top 3.54 in. (90 mm) CAUTION The sides of the refrigerator are warm surfaces. The warmth felt on the left and right sides of the fridge is normal for this cooling technology.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502730.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-09-09
igerator drawers and freezer baskets, position the appliance where both can open fully. INSTALLATION CAUTION Do Not install the appliance where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the appliance. NOTE If you place your appliance with the door hinge side against a wall, you may have to allow additional space for the handle so you can open the door wider. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential-type environments WARNING Installation Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 1.57 in. (40 mm) Back 1.97 in. (50 mm) Top 3.54 in. (90 mm) CAUTION The sides of the refrigerator are warm surfaces. The warmth felt on the left and right sides of the fridge is normal for this cooling technology.
igerator drawers and freezer baskets, position the appliance where both can open fully. INSTALLATION CAUTION Do Not install the appliance where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the appliance. NOTE If you place your appliance with the door hinge side against a wall, you may have to allow additional space for the handle so you can open the door wider. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential-type environments WARNING Installation Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 1.57 in. (40 mm) Back 1.97 in. (50 mm) Top 3.54 in. (90 mm) CAUTION The sides of the refrigerator are warm surfaces. The warmth felt on the left and right sides of the fridge is normal for this cooling technology.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Frigidaire Gallery measurement source — 103502727.pdf Publisher not recorded
Page 1
Value used by ExactFit
1.31875 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: (32.4375 - 29.8) / 2
Confidence label: high.
Primary evidence
Frigidaire Gallery measurement source — 103502727.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-10-25
Exact-model Frigidaire Gallery specification: Width With Doors 90° Open 32 7/16", Width of Cabinet 29 51/64". Two doors hinge on the outer sides, so the extra width is split between the sides: 1 5/16" beside a wall for the door to open to 90°.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
Exact-model Frigidaire Gallery specification: Width With Doors 90° Open 32 7/16", Width of Cabinet 29 51/64". Two doors hinge on the outer sides, so the extra width is split between the sides: 1 5/16" beside a wall for the door to open to 90°. Calculation or inference: (32.4375 - 29.8) / 2.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded
No retained excerpt is available.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
No evidence decision recorded.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire Gallery installation document — 103502727.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Selected: 32.94 in. Earlier retained values: 33.14 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Frigidaire Gallery installation-envelope calculation: case_width_in=29.8, side_ventilation_clearance_in=1.57; result=32.94 in. Product source: 103502727.pdf. Clearance source text: igerator drawers and freezer baskets, position the appliance where both can open fully. INSTALLATION CAUTION Do Not install the appliance where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the appliance. NOTE If you place your appliance with the door hinge side against a wall, you may have to allow additional space for the handle so you can open the door wider. WARNING This appliance is intended for use in residential household and similar interior applications such as: • Kitchen / Kitchenette • Pantry Room • Basement • Enclosed Garage • Other interior residential-type environments WARNING Installation Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides 1.57 in. (40 mm) Back 1.97 in. (50 mm) Top 3.54 in. (90 mm) CAUTION The sides of the refrigerator are warm surfaces. The warmth felt on the left and right sides of the fridge is normal for this cooling technology. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in.
Model numbers covered: GRBN2012AF. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
9 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-10-25. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
