Measurement evidence for Frigidaire FRTE1936AS

Value used by ExactFit

29.7 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire FRTE1936AS Product Specifications Sheet
assets.skulytics.io · Product Specifications Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width 29 7/10"

Why this value was used

Width 29 7/10"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

66 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire FRTE1936AS Product Specifications Sheet
assets.skulytics.io · Product Specifications Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height Without Hinge 66"

Why this value was used

Height Without Hinge 66"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

66.5625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire FRTE1936AS Product Specifications Sheet
assets.skulytics.io · Product Specifications Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height With Hinge 66 9/16"

Why this value was used

Height With Hinge 66 9/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire FRTE1936AS Product Specifications Sheet
assets.skulytics.io · Product Specifications Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth of Cabinet 26 3/4"

Why this value was used

Depth of Cabinet 26 3/4"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

30.7 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire FRTE1936AS Product Specifications Sheet
assets.skulytics.io · Product Specifications Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door 30 7/10"

Why this value was used

Depth With Door 30 7/10"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

32.125 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire FRTE1936AS Product Specifications Sheet
assets.skulytics.io · Product Specifications Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door and Handle 32 1/8"

Why this value was used

Depth With Door and Handle 32 1/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

57.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire FRTE1936AS Product Specifications Sheet
assets.skulytics.io · Product Specifications Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door 90° Open 57 1/2"

Why this value was used

Depth With Door 90° Open 57 1/2"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30.45 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: width_doors_closed_in + 2 * side_clearance_wall_in = 30.45

Confidence label: high.

Calculation inputs: Overall width; Adjoining-wall clearance (reviewed endpoint);

Primary evidence

Frigidaire measurement source — https://frigidaire.bynder.com/asset/b6ccb857-872c-4e40-abb3-52dc05e40432/FRTE1936A_EN-pdf.pdf
frigidaire.bynder.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Reviewed appliance width (Width 29 7/10") plus reviewed per-side installation clearance (connections
Reviewed: 2026-09-04

Reviewed appliance width (Width 29 7/10") plus reviewed per-side installation clearance (connections: | • Top 3/8" (9.5 mm) | • Sides 3/8" (9.5 mm) | deterministic pattern: installation_sides); width_doors_closed_in + 2 * side_clearance_wall_in = 30.45 in

Why this value was used

Reviewed appliance width (Width 29 7/10") plus reviewed per-side installation clearance (connections: | • Top 3/8" (9.5 mm) | • Sides 3/8" (9.5 mm) | deterministic pattern: installation_sides); width_doors_closed_in + 2 * side_clearance_wall_in = 30.45 in Calculation or inference: width_doors_closed_in + 2 * side_clearance_wall_in = 30.45.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

66.9375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Frigidaire FRTE1936AS Complete Owner's Guide
assets.skulytics.io · Complete Owner's Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 66.5625 in plus documented top clearance 0.375 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 66.5625 in plus documented top clearance 0.375 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Frigidaire FRTE1936AS Complete Owner's Guide
assets.skulytics.io · Complete Owner's Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 26.75 in plus documented rear clearance 2.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 26.75 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire FRTE1936AS Complete Owner's Guide
assets.skulytics.io · Complete Owner's Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

connections: | • Top 3/8" (9.5 mm) | • Sides 3/8" (9.5 mm) | deterministic pattern: installation_sides

Why this value was used

connections: | • Top 3/8" (9.5 mm) | • Sides 3/8" (9.5 mm) | deterministic pattern: installation_sides

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire FRTE1936AS Complete Owner's Guide
assets.skulytics.io · Complete Owner's Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

connections: | • Top 3/8" (9.5 mm) | • Sides 3/8" (9.5 mm) | deterministic pattern: installation_sides

Why this value was used

connections: | • Top 3/8" (9.5 mm) | • Sides 3/8" (9.5 mm) | deterministic pattern: installation_sides

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire FRTE1936AS Complete Owner's Guide
assets.skulytics.io · Complete Owner's Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

connections: | • Top 3/8" (9.5 mm) | • Sides 3/8" (9.5 mm) | deterministic pattern: installation_sides

Why this value was used

connections: | • Top 3/8" (9.5 mm) | • Sides 3/8" (9.5 mm) | deterministic pattern: installation_sides

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Frigidaire FRTE1936AS Complete Owner's Guide
assets.skulytics.io · Complete Owner's Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

• Sides 3/8" (9.5 mm) | • Back 2" (50.8 mm) | NOTE

Why this value was used

• Sides 3/8" (9.5 mm) | • Back 2" (50.8 mm) | NOTE

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: hinge-side baseline = documented side ventilation clearance

Confidence label: medium.

Primary evidence

Frigidaire FRTE1936AS Complete Owner's Guide
assets.skulytics.io · Complete Owner's Guide
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

connections: | • Top 3/8" (9.5 mm) | • Sides 3/8" (9.5 mm) | deterministic pattern: installation_sides Hinge-side wall note is conditional and gives no separate numeric minimum; this value is the documented side-clearance baseline.

Why this value was used

A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.

Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.7 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire FRTE1936AS Product Specifications Sheet
assets.skulytics.io · Product Specifications Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width of Cabinet 29 7/10"

Why this value was used

Width of Cabinet 29 7/10"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

0.375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Frigidaire FRTE1936AS Complete Owner's Guide
assets.skulytics.io · Complete Owner's Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-04

connections: | • Top 3/8" (9.5 mm) | • Sides 3/8" (9.5 mm) | deterministic pattern: installation_sides

Why this value was used

connections: | • Top 3/8" (9.5 mm) | • Sides 3/8" (9.5 mm) | deterministic pattern: installation_sides

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.