Measurement evidence for Frigidaire FRTE1622AS

Value used by ExactFit

27.5625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 83575470.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width 27 9/16"

Why this value was used

Width 27 9/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

64.9 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire measurement source — FRTE1622AS
www.homedepot.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-chassis specification: Height to Top of Refrigerator Case 64.9 in; finish variants share the s
Reviewed: 2026-09-04

Exact-chassis specification: Height to Top of Refrigerator Case 64.9 in; finish variants share the same manufacturer dimensions.

Why this value was used

Exact-chassis specification: Height to Top of Refrigerator Case 64.9 in; finish variants share the same manufacturer dimensions.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

64.9 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 83575470.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height With Hinge 64 9/10"

Why this value was used

Height With Hinge 64 9/10"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25.5938 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 83575470.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth of Cabinet 25 19/32"

Why this value was used

Depth of Cabinet 25 19/32"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.5625 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 83575470.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door 28 9/16"

Why this value was used

Depth With Door 28 9/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

28.5625 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 83575470.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door and Handle 28 9/16"

Why this value was used

Depth With Door and Handle 28 9/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

53.8906 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 83575470.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door 90° Open 53 57/64"

Why this value was used

Depth With Door 90° Open 53 57/64"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.4225 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case_width_in + 2 * side_ventilation_clearance_in

Confidence label: high.

Calculation inputs: Left-side ventilation clearance; Cabinet case width;

Primary evidence

Frigidaire measurement source — 103506176.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-09

Frigidaire family installation-envelope calculation: case_width_in=27.5625, side_ventilation_clearance_in=3.93; result=35.4225 in. Product operand source: 83575470.pdf.

Why this value was used

Frigidaire family installation-envelope calculation: case_width_in=27.5625, side_ventilation_clearance_in=3.93; result=35.4225 in. Product operand source: 83575470.pdf. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in.

Other evidence found

• 28.3125 in — superseded

  An earlier brand-wide assumption (no document for this model); location not retained. Model scope: not separately recorded. Raw value: Derived minimum opening width 28.3125 in from product width 27.5625 in and explicit 0.375 in clearance on each side.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.83 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: height_hinge_in + top_clearance_in

Confidence label: high.

Calculation inputs: Height with hinge / controlling height; Top clearance;

Primary evidence

Frigidaire measurement source — 103506176.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-09

Frigidaire family installation-envelope calculation: height_hinge_in=64.9, top_clearance_in=3.93; result=68.83 in. Product operand source: 83575470.pdf.

Why this value was used

Frigidaire family installation-envelope calculation: height_hinge_in=64.9, top_clearance_in=3.93; result=68.83 in. Product operand source: 83575470.pdf. Calculation or inference: height_hinge_in + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.5438 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: high.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Frigidaire measurement source — 103506176.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-09

Frigidaire family installation-envelope calculation: depth_case_only_in=25.5938, rear_clearance_in=2.95; result=28.5438 in. Product operand source: 83575470.pdf.

Why this value was used

Frigidaire family installation-envelope calculation: depth_case_only_in=25.5938, rear_clearance_in=2.95; result=28.5438 in. Product operand source: 83575470.pdf. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.93 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 103506176.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-05

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides, Top 3.93" (100 mm) Back 2.95" (75 mm) To level the cabinet using the front leveling feet: • Lower the leveling feet on each side clockwise until they contact the fl oor. Lower Raise • Use the leveling feet (located on the front) ensuring all 4 corners of the unit are resting fi rmly on a solid fl oor. Turn the leveling feet clockwise to retract the feet and counterclockwi

Why this value was used

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides, Top 3.93" (100 mm) Back 2.95" (75 mm) To level the cabinet using the front leveling feet: • Lower the leveling feet on each side clockwise until they contact the fl oor. Lower Raise • Use the leveling feet (located on the front) ensuring all 4 corners of the unit are resting fi rmly on a solid fl oor. Turn the leveling feet clockwise to retract the feet and counterclockwi

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.93 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 103506176.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-05

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides, Top 3.93" (100 mm) Back 2.95" (75 mm) To level the cabinet using the front leveling feet: • Lower the leveling feet on each side clockwise until they contact the fl oor. Lower Raise • Use the leveling feet (located on the front) ensuring all 4 corners of the unit are resting fi rmly on a solid fl oor. Turn the leveling feet clockwise to retract the feet and counterclockwi

Why this value was used

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides, Top 3.93" (100 mm) Back 2.95" (75 mm) To level the cabinet using the front leveling feet: • Lower the leveling feet on each side clockwise until they contact the fl oor. Lower Raise • Use the leveling feet (located on the front) ensuring all 4 corners of the unit are resting fi rmly on a solid fl oor. Turn the leveling feet clockwise to retract the feet and counterclockwi

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.93 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 103506176.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-09

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides, Top 3.93" (100 mm) Back 2.95" (75 mm) To level the cabinet using the front leveling feet: • Lower the leveling feet on each side clockwise until they contact the fl oor. Lower Raise • Use the leveling feet (located on the front) ensuring all 4 corners of the unit are resting fi rmly on a solid fl oor. Turn the leveling feet clockwise to retract the feet and counterclockwi

Why this value was used

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides, Top 3.93" (100 mm) Back 2.95" (75 mm) To level the cabinet using the front leveling feet: • Lower the leveling feet on each side clockwise until they contact the fl oor. Lower Raise • Use the leveling feet (located on the front) ensuring all 4 corners of the unit are resting fi rmly on a solid fl oor. Turn the leveling feet clockwise to retract the feet and counterclockwi

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2.95 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 103506176.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-09

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides, Top 3.93" (100 mm) Back 2.95" (75 mm) To level the cabinet using the front leveling feet: • Lower the leveling feet on each side clockwise until they contact the fl oor. Lower Raise • Use the leveling feet (located on the front) ensuring all 4 corners of the unit are resting fi rmly on a solid fl oor. Turn the leveling feet clockwise to retract the feet and counterclockwi

Why this value was used

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides, Top 3.93" (100 mm) Back 2.95" (75 mm) To level the cabinet using the front leveling feet: • Lower the leveling feet on each side clockwise until they contact the fl oor. Lower Raise • Use the leveling feet (located on the front) ensuring all 4 corners of the unit are resting fi rmly on a solid fl oor. Turn the leveling feet clockwise to retract the feet and counterclockwi

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.390625 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 27.953125 - 27.5625

Confidence label: high.

Primary evidence

Frigidaire measurement source — 83575470.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-25

Exact-model Frigidaire specification: Width With Doors 90° Open 27 61/64", Width of Cabinet 27 9/16". One door; the extra width is all on the hinge side: 25/64" beside a wall for the door to open to 90°.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Exact-model Frigidaire specification: Width With Doors 90° Open 27 61/64", Width of Cabinet 27 9/16". One door; the extra width is all on the hinge side: 25/64" beside a wall for the door to open to 90°. Calculation or inference: 27.953125 - 27.5625.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

27.5625 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 83575470.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width of Cabinet 27 9/16"

Why this value was used

Width of Cabinet 27 9/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.