This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-22. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire measurement source — specification-sheet-FRSS2623A-10-25.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Width 36 1/8" Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Height Without Hinge 68 5/8"
Value used by ExactFit
68.625 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire measurement source — specification-sheet-FRSS2623A-10-25.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Height Without Hinge 68 5/8" Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Height With Hinge 69 7/8"
Value used by ExactFit
69.875 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire measurement source — specification-sheet-FRSS2623A-10-25.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Height With Hinge 69 7/8" Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Depth of Cabinet 28 3/4"
Value used by ExactFit
28.75 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire measurement source — specification-sheet-FRSS2623A-10-25.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Depth of Cabinet 28 3/4" Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Depth With Door 32 1/2"
Value used by ExactFit
32.5 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire measurement source — specification-sheet-FRSS2623A-10-25.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Depth With Door 32 1/2" Reviewed: 2026-09-09
Retained specification excerpt: Depth With Door and Handle 35"
Value used by ExactFit
35 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire measurement source — specification-sheet-FRSS2623A-10-25.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Depth With Door and Handle 35" Reviewed: 2026-09-09
Retained specification excerpt: Depth With Door 90° Open 50"
Value used by ExactFit
50 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire measurement source — specification-sheet-FRSS2623A-10-25.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Depth With Door 90° Open 50" Reviewed: 2026-09-09
Frigidaire measurement source — specification-sheet-FRSS2623A-10-25.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-10-22
Frigidaire family installation-envelope calculation: case_width_in=35.875 (Width of Cabinet 35 7/8", specification sheet FRSS2623A), side_ventilation_clearance_in=0.375; result=36.625 in, as for the other finishes.
Frigidaire family installation-envelope calculation: case_width_in=35.875 (Width of Cabinet 35 7/8", specification sheet FRSS2623A), side_ventilation_clearance_in=0.375; result=36.625 in, as for the other finishes. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in.
Other evidence found
36.875 in — superseded
Document specification-sheet-FRSS2623A-10-25.pdf; location not retained. Model scope: not separately recorded. Raw value: {"calculation": "width_doors_closed_in + 2 * side_ventilation_clearance_in", "operands": {"side_ventilation_clearance_in": [{"cache_path": "data/sources/Frigidaire/FRSS2623AS/complete-owners-guide-A19894509en.pdf", "page": "PDF page 7, INSTALLATION, Installation clearances", "raw": "Allow the following clearances for ease of installation, proper air circulations, and plumbing and electrical connections: Sides & Top ⅜\" Back 1\".", "source_url": "https://frigidaire.bynder.com/asset/b4a51d62-e6d4-4002-bc04-fe4c39406838/A19894509en-pdf.pdf", "value_in": 0.375}], "width_doors_closed_in": [{"cache_path": "data/sources/Frigidaire/FRSS2623AS/specification-sheet-FRSS2623A-10-25.pdf", "page": "PDF page 1, Dimensions and Volume table", "raw": "Width 36 1/8\"", "source_url": "https://frigidaire.bynder.com/asset/aaced83f-2397-41d9-bc4f-690fc8067671/FRSS2623A_EN-pdf.pdf", "value_in": 36.125}, {"cache_path": "docs/provider-evaluation/raw/skulytics/active-residential-refrigerators-1000-20260817/documents/Frigidaire/FRSS2623ASC1/103506724.pdf", "page": 1, "raw": "Width\n36 1/8\"", "source_url": "https://assets.skulytics.io/assets/docs/FRSS2623ASC1_103506724.pdf", "value_in": 36.125}]}, "result_in": 36.875}. The final reviewed registry supersedes this earlier audit value.
36.875 in — superseded
Document complete-owners-guide-A19894509en.pdf; location not retained. Model scope: not separately recorded. Raw value: Frigidaire family installation-envelope calculation: case_width_in=36.125, side_ventilation_clearance_in=0.375; result=36.875 in. Product operand source: data/sources/Frigidaire/FRSS2623AS/specification-sheet-FRSS2623A-10-25.pdf.. The final reviewed registry supersedes this earlier audit value.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Frigidaire measurement source — complete-owners-guide-A19894509en.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Frigidaire family installation-envelope calculation: height_hinge_in=69.875, top_clearance_in=0.375; Reviewed: 2026-09-09
Frigidaire family installation-envelope calculation: height_hinge_in=69.875, top_clearance_in=0.375; result=70.25 in. Product operand source: data/sources/Frigidaire/FRSS2623AS/specification-sheet-FRSS2623A-10-25.pdf.
Frigidaire family installation-envelope calculation: height_hinge_in=69.875, top_clearance_in=0.375; result=70.25 in. Product operand source: data/sources/Frigidaire/FRSS2623AS/specification-sheet-FRSS2623A-10-25.pdf. Calculation or inference: height_hinge_in + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Frigidaire measurement source — complete-owners-guide-A19894509en.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Frigidaire family installation-envelope calculation: depth_case_only_in=28.75, rear_clearance_in=1; Reviewed: 2026-09-09
Frigidaire family installation-envelope calculation: depth_case_only_in=28.75, rear_clearance_in=1; result=29.75 in. Product operand source: data/sources/Frigidaire/FRSS2623AS/specification-sheet-FRSS2623A-10-25.pdf.
Frigidaire family installation-envelope calculation: depth_case_only_in=28.75, rear_clearance_in=1; result=29.75 in. Product operand source: data/sources/Frigidaire/FRSS2623AS/specification-sheet-FRSS2623A-10-25.pdf. Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Allow the following clearances for ease of installation, proper air circulations, and plumbing and e
Value used by ExactFit
0.375 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire measurement source — complete-owners-guide-A19894509en.pdf frigidaire.bynder.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Allow the following clearances for ease of installation, proper air circulations, and plumbing and e Reviewed: 2026-09-09
Allow the following clearances for ease of installation, proper air circulations, and plumbing and electrical connections: Sides & Top ⅜" Back 1".
Allow the following clearances for ease of installation, proper air circulations, and plumbing and electrical connections: Sides & Top ⅜" Back 1".
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Allow the following clearances for ease of installation, proper air circulations, and plumbing and e
Value used by ExactFit
0.375 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire measurement source — complete-owners-guide-A19894509en.pdf frigidaire.bynder.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Allow the following clearances for ease of installation, proper air circulations, and plumbing and e Reviewed: 2026-09-09
Allow the following clearances for ease of installation, proper air circulations, and plumbing and electrical connections: Sides & Top ⅜" Back 1".
Allow the following clearances for ease of installation, proper air circulations, and plumbing and electrical connections: Sides & Top ⅜" Back 1".
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Allow the following clearances for ease of installation, proper air circulations, and plumbing and e
Value used by ExactFit
0.375 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire measurement source — complete-owners-guide-A19894509en.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Allow the following clearances for ease of installation, proper air circulations, and plumbing and e Reviewed: 2026-09-09
Allow the following clearances for ease of installation, proper air circulations, and plumbing and electrical connections: Sides & Top ⅜" Back 1".
Allow the following clearances for ease of installation, proper air circulations, and plumbing and electrical connections: Sides & Top ⅜" Back 1".
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Allow the following clearances for ease of installation, proper air circulations, and plumbing and e
Value used by ExactFit
1 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire measurement source — complete-owners-guide-A19894509en.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Allow the following clearances for ease of installation, proper air circulations, and plumbing and e Reviewed: 2026-09-09
Allow the following clearances for ease of installation, proper air circulations, and plumbing and electrical connections: Sides & Top ⅜" Back 1".
Allow the following clearances for ease of installation, proper air circulations, and plumbing and electrical connections: Sides & Top ⅜" Back 1".
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded
No retained excerpt is available.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
No evidence decision recorded.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded
No retained excerpt is available.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
No evidence decision recorded.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire measurement source — specification-sheet-FRSS2623A-10-25.pdf frigidaire.bynder.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-10-22
Frigidaire specification sheet FRSS2623A (Available Products: FRSS2623AB, FRSS2623AD, FRSS2623AS, FRSS2623AW), Dimensions and Volume: "Width 36 1/8"" and "Width of Cabinet 35 7/8"". The stored 36 1/8 was the overall width read as the cabinet width; the other three finishes store 35 7/8 from the same sheet.
Frigidaire specification sheet FRSS2623A (Available Products: FRSS2623AB, FRSS2623AD, FRSS2623AS, FRSS2623AW), Dimensions and Volume: "Width 36 1/8"" and "Width of Cabinet 35 7/8"". The stored 36 1/8 was the overall width read as the cabinet width; the other three finishes store 35 7/8 from the same sheet.
Other evidence found
36.125 in — superseded
Document specification-sheet-FRSS2623A-10-25.pdf; location not retained. Model scope: not separately recorded. Raw value: Width 36 1/8". The final reviewed registry supersedes this earlier audit value.
Effect on fit result
This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Selected: 36.625 in. Earlier retained values: 36.875 in, 36.875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Frigidaire family installation-envelope calculation: case_width_in=35.875 (Width of Cabinet 35 7/8", specification sheet FRSS2623A), side_ventilation_clearance_in=0.375; result=36.625 in, as for the other finishes. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in.
Selected: 35.875 in. Earlier retained values: 36.125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Frigidaire specification sheet FRSS2623A (Available Products: FRSS2623AB, FRSS2623AD, FRSS2623AS, FRSS2623AW), Dimensions and Volume: "Width 36 1/8"" and "Width of Cabinet 35 7/8"". The stored 36 1/8 was the overall width read as the cabinet width; the other three finishes store 35 7/8 from the same sheet.
frigidaire.bynder.com · Web source · secondary model/source
Model numbers covered: FRSS2623AS. Publication/revision date: Not recorded. Reviewed: 2026-10-22.
9 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-10-22. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
