Measurement evidence for Frigidaire FRSG2115AV

Value used by ExactFit

35.8125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 90272331.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width 35 13/16"

Why this value was used

Width 35 13/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.7 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire measurement source — 5015635209
www.lowes.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model specification: Height to Top of Case 69.7 in.
Reviewed: 2026-09-04

Exact-model specification: Height to Top of Case 69.7 in.

Why this value was used

Exact-model specification: Height to Top of Case 69.7 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.7 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 90272331.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height With Hinge 69 7/10"

Why this value was used

Height With Hinge 69 7/10"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.8125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 90272331.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth of Cabinet 24 13/16"

Why this value was used

Depth of Cabinet 24 13/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.6875 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 90272331.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door 28 11/16"

Why this value was used

Depth With Door 28 11/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

28.6875 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 28.6875 in Depth With Door + 0 in projecting handle = 28.6875 in maximum closed depth

Confidence label: high.

Primary evidence

Frigidaire measurement source — FRSG2115A_EN-pdf.pdf
frigidaire.bynder.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-10

Exact-model version 11/25 sheet prints Depth With Door = 28 11/16 in; its product image visibly shows recessed vertical grip channels and no projecting exterior handles.

Why this value was used

Exact-model version 11/25 sheet prints Depth With Door = 28 11/16 in; its product image visibly shows recessed vertical grip channels and no projecting exterior handles. Calculation or inference: 28.6875 in Depth With Door + 0 in projecting handle = 28.6875 in maximum closed depth.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

41.6875 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 90272331.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door 90° Open 41 11/16"

Why this value was used

Depth With Door 90° Open 41 11/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

37.8125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case_width_in + 2 * side_ventilation_clearance_in

Confidence label: high.

Calculation inputs: Left-side ventilation clearance; Cabinet case width;

Primary evidence

Frigidaire measurement source — 90272329.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-09

Frigidaire family installation-envelope calculation: case_width_in=35.8125, side_ventilation_clearance_in=1; result=37.8125 in. Product operand source: 90272331.pdf.

Why this value was used

Frigidaire family installation-envelope calculation: case_width_in=35.8125, side_ventilation_clearance_in=1; result=37.8125 in. Product operand source: 90272331.pdf. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in.

Other evidence found

• 36.3125 in — superseded

  Document 90272331.pdf + Document 90272329.pdf; location not retained. Model scope: not separately recorded. Raw value: Derived minimum opening width 36.3125 in from product width 35.8125 in and explicit 0.25 in clearance on each side.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.7 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: height_hinge_in + top_clearance_in

Confidence label: high.

Calculation inputs: Height with hinge / controlling height; Top clearance;

Primary evidence

Frigidaire measurement source — 90272329.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-09

Frigidaire family installation-envelope calculation: height_hinge_in=69.7, top_clearance_in=1; result=70.7 in. Product operand source: 90272331.pdf.

Why this value was used

Frigidaire family installation-envelope calculation: height_hinge_in=69.7, top_clearance_in=1; result=70.7 in. Product operand source: 90272331.pdf. Calculation or inference: height_hinge_in + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26.8125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: high.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Frigidaire measurement source — 90272329.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-09

Frigidaire family installation-envelope calculation: depth_case_only_in=24.8125, rear_clearance_in=2; result=26.8125 in. Product operand source: 90272331.pdf.

Why this value was used

Frigidaire family installation-envelope calculation: depth_case_only_in=24.8125, rear_clearance_in=2; result=26.8125 in. Product operand source: 90272331.pdf. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 90272329.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top 1" Back 2" Location • Choose a place that is near a ground­ ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. CAUTION Do Not install t

Why this value was used

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top 1" Back 2" Location • Choose a place that is near a ground­ ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. CAUTION Do Not install t

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 90272329.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top 1" Back 2" Location • Choose a place that is near a ground­ ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. CAUTION Do Not install t

Why this value was used

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top 1" Back 2" Location • Choose a place that is near a ground­ ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. CAUTION Do Not install t

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 90272329.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top 1" Back 2" Location • Choose a place that is near a ground­ ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. CAUTION Do Not install t

Why this value was used

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top 1" Back 2" Location • Choose a place that is near a ground­ ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. CAUTION Do Not install t

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 90272329.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top 1" Back 2" Location • Choose a place that is near a ground­ ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. CAUTION Do Not install t

Why this value was used

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Sides & Top 1" Back 2" Location • Choose a place that is near a ground­ ed electrical outlet. Do Not use an extension cord or an adapter plug. • If possible, place the unit out of direct sunlight and away from the range, dishwasher or other heat sources. • Install the appliance on a floor that is level and strong enough to support a fully loaded unit. CAUTION Do Not install t

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.859375 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (37.53125 - 35.8125) / 2

Confidence label: high.

Primary evidence

Frigidaire measurement source — official-2025-11-product-spec.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-25

Exact-model Frigidaire specification: Width With Doors 90° Open 37 17/32", Width of Cabinet 35 13/16". Two doors hinge on the outer sides, so the extra width is split between the sides: 55/64" beside a wall for the door to open to 90°.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Exact-model Frigidaire specification: Width With Doors 90° Open 37 17/32", Width of Cabinet 35 13/16". Two doors hinge on the outer sides, so the extra width is split between the sides: 55/64" beside a wall for the door to open to 90°. Calculation or inference: (37.53125 - 35.8125) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.8125 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 90272331.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width of Cabinet 35 13/16"

Why this value was used

Width of Cabinet 35 13/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.