This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-09. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 29.5 in | ✓ Verified — retained secondary source | Frigidaire installation document — 106297428.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit29.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 106297428.pdf Width 29 1/2"Open original source ↗ Why this value was usedWidth 29 1/2" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 66.6 in | ✓ Verified — retained secondary source | Frigidaire measurement source — 341982043 www.homedepot.com | Retained specification excerpt: Exact-model specification: Height to Top of Refrigerator Case 66.6 in; also confirmed by Best Buy. | |
Value used by ExactFit66.6 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire measurement source — 341982043 Exact-model specification: Height to Top of Refrigerator Case 66.6 in; also confirmed by Best Buy.Open original source ↗ Why this value was usedExact-model specification: Height to Top of Refrigerator Case 66.6 in; also confirmed by Best Buy. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 66.6 in | ✓ Verified — retained secondary source | Frigidaire installation document — 106297428.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit66.6 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 106297428.pdf Height With Hinge 66 3/5"Open original source ↗ Why this value was usedHeight With Hinge 66 3/5" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 27 in | ✓ Verified — retained secondary source | Frigidaire measurement source — 341982043 www.homedepot.com | Retained specification excerpt: Frigidaire Support exact-model answer: cabinet without doors is exactly 27 inches; replaces corrupt | |
Value used by ExactFit27 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire measurement source — 341982043 Frigidaire Support exact-model answer: cabinet without doors is exactly 27 inches; replaces corrupt retailer template field.Open original source ↗ Why this value was usedFrigidaire Support exact-model answer: cabinet without doors is exactly 27 inches; replaces corrupt retailer template field. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 30.9 in | ✓ Verified — retained secondary source | Frigidaire installation document — 106297428.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit30.9 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 106297428.pdf Depth With Door 30 9/10"Open original source ↗ Why this value was usedDepth With Door 30 9/10" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 33.8 in | ✓ Verified — retained secondary source | Frigidaire installation document — 106297428.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit33.8 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 106297428.pdf Depth With Door and Handle 33 4/5"Open original source ↗ Why this value was usedDepth With Door and Handle 33 4/5" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 43 in | ✓ Verified — retained secondary source | Frigidaire measurement source — 341982043 www.homedepot.com | Retained specification excerpt: Frigidaire Support exact-model answer: depth with doors open 90 degrees is approximately 43 inches. | |
Value used by ExactFit43 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceFrigidaire measurement source — 341982043 Frigidaire Support exact-model answer: depth with doors open 90 degrees is approximately 43 inches.Open original source ↗ Why this value was usedFrigidaire Support exact-model answer: depth with doors open 90 degrees is approximately 43 inches. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 30.25 in | ✓ Verified — retained secondary source · Calculated/inferred | Frigidaire measurement source — 106297430.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit30.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: case_width_in + 2 * side_ventilation_clearance_in Confidence label: high. Calculation inputs: Left-side ventilation clearance; Cabinet case width; Primary evidenceFrigidaire measurement source — 106297430.pdf Frigidaire family installation-envelope calculation: case_width_in=29.5, side_ventilation_clearance_in=0.375; result=30.25 in. Product operand source: 106297428.pdf.Open original source ↗ Why this value was usedFrigidaire family installation-envelope calculation: case_width_in=29.5, side_ventilation_clearance_in=0.375; result=30.25 in. Product operand source: 106297428.pdf. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 66.975 in | ✓ Verified — retained secondary source · Calculated/inferred | Frigidaire measurement source — 106297430.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit66.975 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: height_hinge_in + top_clearance_in Confidence label: high. Calculation inputs: Height with hinge / controlling height; Top clearance; Primary evidenceFrigidaire measurement source — 106297430.pdf Frigidaire family installation-envelope calculation: height_hinge_in=66.6, top_clearance_in=0.375; result=66.975 in. Product operand source: 106297428.pdf.Open original source ↗ Why this value was usedFrigidaire family installation-envelope calculation: height_hinge_in=66.6, top_clearance_in=0.375; result=66.975 in. Product operand source: 106297428.pdf. Calculation or inference: height_hinge_in + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 29 in | ✓ Verified — retained secondary source · Calculated/inferred | Frigidaire measurement source — 106297430.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit29 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: high. Calculation inputs: Depth without door; Rear clearance; Primary evidenceFrigidaire measurement source — 106297430.pdf Frigidaire family installation-envelope calculation: depth_case_only_in=27, rear_clearance_in=2; result=29 in. Product operand source: https://www.homedepot.com/p/341982043.Open original source ↗ Why this value was usedFrigidaire family installation-envelope calculation: depth_case_only_in=27, rear_clearance_in=2; result=29 in. Product operand source: https://www.homedepot.com/p/341982043. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.375 in | ✓ Verified — retained secondary source | Frigidaire measurement source — 106297430.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire measurement source — 106297430.pdf connections: | • Top 3/8" (9.5 mm) | • Sides 3/8" (9.5 mm) | deterministic pattern: installation_sidesOpen original source ↗ Why this value was usedconnections: | • Top 3/8" (9.5 mm) | • Sides 3/8" (9.5 mm) | deterministic pattern: installation_sides Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.375 in | ✓ Verified — retained secondary source | Frigidaire measurement source — 106297430.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire measurement source — 106297430.pdf connections: | • Top 3/8" (9.5 mm) | • Sides 3/8" (9.5 mm) | deterministic pattern: installation_sidesOpen original source ↗ Why this value was usedconnections: | • Top 3/8" (9.5 mm) | • Sides 3/8" (9.5 mm) | deterministic pattern: installation_sides Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.375 in | ✓ Verified — retained secondary source | Frigidaire measurement source — 106297430.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire measurement source — 106297430.pdf connections: | • Top 3/8" (9.5 mm) | • Sides 3/8" (9.5 mm) | deterministic pattern: installation_sidesOpen original source ↗ Why this value was usedconnections: | • Top 3/8" (9.5 mm) | • Sides 3/8" (9.5 mm) | deterministic pattern: installation_sides Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Verified — retained secondary source | Frigidaire installation document — 106297430.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 106297430.pdf Allow the following clearances for ease of installation, proper air circulation, plumbing, and electrical connections: • Top 3/8" (9.5 mm) • Sides 3/8" (9.5 mm) • Back 2" (50.8 mm) NOTE If you place the appliance with the door hinge side against a wall, you may have to allow additional space so the door can be open wider. 3.3 Leveling Feet Level the appliance by raising or lowering the front adjustable feet. 1. To raise the appliance turn the feet clockwise. 2. To lower the appliance turn the fOpen original source ↗ Why this value was usedAllow the following clearances for ease of installation, proper air circulation, plumbing, and electrical connections: • Top 3/8" (9.5 mm) • Sides 3/8" (9.5 mm) • Back 2" (50.8 mm) NOTE If you place the appliance with the door hinge side against a wall, you may have to allow additional space so the door can be open wider. 3.3 Leveling Feet Level the appliance by raising or lowering the front adjustable feet. 1. To raise the appliance turn the feet clockwise. 2. To lower the appliance turn the f Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 29.5 in | ✓ Verified — retained secondary source | Frigidaire installation document — 106297428.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit29.5 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 106297428.pdf Width of Cabinet 29 1/2"Open original source ↗ Why this value was usedWidth of Cabinet 29 1/2" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: FRFN1801AF. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
5 displayed measurements supported: Overall width; Height with hinge / controlling height; Depth with door, without handles; Depth with handle; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗www.homedepot.com · Web source · secondary model/source
Model numbers covered: FRFN1801AF. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
3 displayed measurements supported: Cabinet height; Depth without door; Depth with doors open at 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: FRFN1801AF. Publication/revision date: Not recorded. Reviewed: 2026-09-09.
7 displayed measurements supported: Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-09. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.