Measurement evidence for Frigidaire FRFG2033AV

Value used by ExactFit

32.8 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 106160531.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width 32 4/5"

Why this value was used

Width 32 4/5"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.8 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire measurement source — 106160531.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-04

Height Without Hinge 68 4/5". The stored 68.4 read the fraction 4/5 as a decimal .4.

Why this value was used

Height Without Hinge 68 4/5". The stored 68.4 read the fraction 4/5 as a decimal .4.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.7 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 106160531.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height With Hinge 69 7/10"

Why this value was used

Height With Hinge 69 7/10"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25.2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire measurement source — 106160531.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-04

Depth of Cabinet 25 1/5". The stored 25.1 read the fraction 1/5 as a decimal .1.

Why this value was used

Depth of Cabinet 25 1/5". The stored 25.1 read the fraction 1/5 as a decimal .1.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.1 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 106160531.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door 29 1/10"

Why this value was used

Depth With Door 29 1/10"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.1 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 106160531.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door and Handle 29 1/10"

Why this value was used

Depth With Door and Handle 29 1/10"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

43.1 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 106160531.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door 90° Open 43 1/10"

Why this value was used

Depth With Door 90° Open 43 1/10"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

33.45 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case_width_in + 2 * side_ventilation_clearance_in

Confidence label: high.

Calculation inputs: Left-side ventilation clearance; Cabinet case width;

Primary evidence

Frigidaire measurement source — 106160534.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-09

Frigidaire family installation-envelope calculation: case_width_in=32.7, side_ventilation_clearance_in=0.375; result=33.45 in. Product operand source: 106160531.pdf.

Why this value was used

Frigidaire family installation-envelope calculation: case_width_in=32.7, side_ventilation_clearance_in=0.375; result=33.45 in. Product operand source: 106160531.pdf. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in.

Other evidence found

• 33.55 in — superseded

  Document 106160531.pdf + Document 106160534.pdf; location not retained. Model scope: not separately recorded. Raw value: Derived minimum opening width 33.55 in from product width 32.8 in and explicit 0.375 in clearance on each side.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.075 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: height_hinge_in + top_clearance_in

Confidence label: high.

Calculation inputs: Height with hinge / controlling height; Top clearance;

Primary evidence

Frigidaire measurement source — 106160534.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-09

Frigidaire family installation-envelope calculation: height_hinge_in=69.7, top_clearance_in=0.375; result=70.075 in. Product operand source: 106160531.pdf.

Why this value was used

Frigidaire family installation-envelope calculation: height_hinge_in=69.7, top_clearance_in=0.375; result=70.075 in. Product operand source: 106160531.pdf. Calculation or inference: height_hinge_in + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

27.2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: high.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Frigidaire measurement source — 106160534.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-10-04

Recalculated 2026-10-04 with the stored formula from current inputs: depth_case_only_in + rear_clearance_in with depth_case_only_in = 25.2, rear_clearance_in = 2 = 27.2 in (previously 27.1 in).

Why this value was used

Recalculated 2026-10-04 with the stored formula from current inputs: depth_case_only_in + rear_clearance_in with depth_case_only_in = 25.2, rear_clearance_in = 2 = 27.2 in (previously 27.1 in). Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

• 27.1 in — superseded

  The same document as the value used above; page 7. Model scope: not separately recorded. Raw value: Recalculated 2026-09-18 with the stored formula from current inputs: depth_case_only_in + rear_clearance_in with depth_case_only_in = 25.1, rear_clearance_in = 2 = 27.1 in (previously 27.2 in).. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire measurement source — 106160534.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-05

• | Sides 3/8" (9.5mm) | • | deterministic pattern: installation_sides

Why this value was used

• | Sides 3/8" (9.5mm) | • | deterministic pattern: installation_sides

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire measurement source — 106160534.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-05

• | Sides 3/8" (9.5mm) | • | deterministic pattern: installation_sides

Why this value was used

• | Sides 3/8" (9.5mm) | • | deterministic pattern: installation_sides

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 106160534.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-09

Allow the following clearances for ease of installation, proper air circulation, plumbing, and electrical connections: • Top 3/8" (9.5mm) • Sides 3/8" (9.5mm) • Back 2" (50.8mm) NOTE If you place the appliance with the door hinge side against a wall, you may have to allow additional space so the door can be open wider. 3.4 Door opening Position the appliance to allow easy access to a counter when removing food. Make sure the refrigerator drawers and freezer baskets can be fully open. 3.5 Cabine

Why this value was used

Allow the following clearances for ease of installation, proper air circulation, plumbing, and electrical connections: • Top 3/8" (9.5mm) • Sides 3/8" (9.5mm) • Back 2" (50.8mm) NOTE If you place the appliance with the door hinge side against a wall, you may have to allow additional space so the door can be open wider. 3.4 Door opening Position the appliance to allow easy access to a counter when removing food. Make sure the refrigerator drawers and freezer baskets can be fully open. 3.5 Cabine

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 106160534.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-05

Allow the following clearances for ease of installation, proper air circulation, plumbing, and electrical connections: • Top 3/8" (9.5mm) • Sides 3/8" (9.5mm) • Back 2" (50.8mm) NOTE If you place the appliance with the door hinge side against a wall, you may have to allow additional space so the door can be open wider. 3.4 Door opening Position the appliance to allow easy access to a counter when removing food. Make sure the refrigerator drawers and freezer baskets can be fully open. 3.5 Cabine

Why this value was used

Allow the following clearances for ease of installation, proper air circulation, plumbing, and electrical connections: • Top 3/8" (9.5mm) • Sides 3/8" (9.5mm) • Back 2" (50.8mm) NOTE If you place the appliance with the door hinge side against a wall, you may have to allow additional space so the door can be open wider. 3.4 Door opening Position the appliance to allow easy access to a counter when removing food. Make sure the refrigerator drawers and freezer baskets can be fully open. 3.5 Cabine

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2.1 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (36.9 - 32.7) / 2

Confidence label: high.

Primary evidence

Frigidaire measurement source — 106160531.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-25

Exact-model Frigidaire specification: Width With Doors 90° Open 36 29/32", Width of Cabinet 32 45/64". Two doors hinge on the outer sides, so the extra width is split between the sides: 2 3/32" beside a wall for the door to open to 90°.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Exact-model Frigidaire specification: Width With Doors 90° Open 36 29/32", Width of Cabinet 32 45/64". Two doors hinge on the outer sides, so the extra width is split between the sides: 2 3/32" beside a wall for the door to open to 90°. Calculation or inference: (36.9 - 32.7) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

32.7 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 106160531.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width of Cabinet 32 7/10"

Why this value was used

Width of Cabinet 32 7/10"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.