This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Counter-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-11. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.3 in | ✓ Verified — retained secondary source | Frigidaire installation document — 104687233.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.3 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 104687233.pdf Width 35 3/10"Open original source ↗ Why this value was usedWidth 35 3/10" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 67.2 in | ✓ Verified — retained secondary source | Frigidaire installation document — 104687233.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit67.2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 104687233.pdf Height Without Hinge 67 1/5"Open original source ↗ Why this value was usedHeight Without Hinge 67 1/5" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 68 in | ✓ Verified — retained secondary source | Frigidaire installation document — 104687233.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit68 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 104687233.pdf Height With Hinge 68"Open original source ↗ Why this value was usedHeight With Hinge 68" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24.8 in | ✓ Verified — retained secondary source | Frigidaire installation document — 104687233.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit24.8 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 104687233.pdf Depth of Cabinet 24 4/5"Open original source ↗ Why this value was usedDepth of Cabinet 24 4/5" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 28.2 in | ✓ Verified — retained secondary source | Frigidaire installation document — 104687233.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit28.2 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 104687233.pdf Depth With Door 28 1/5"Open original source ↗ Why this value was usedDepth With Door 28 1/5" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 28.2 in | ✓ Verified — retained secondary source | Frigidaire installation document — 104687233.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit28.2 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 104687233.pdf Depth With Door and Handle 28 1/5"Open original source ↗ Why this value was usedDepth With Door and Handle 28 1/5" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 43.07 in | ✓ Verified — retained secondary source | Frigidaire measurement source — 337737865 www.homedepot.com | Retained specification excerpt: Exact-model specification: Depth With Door Open 90 Degrees 43.07 in. | |
Value used by ExactFit43.07 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire measurement source — 337737865 Exact-model specification: Depth With Door Open 90 Degrees 43.07 in.Open original source ↗ Why this value was usedExact-model specification: Depth With Door Open 90 Degrees 43.07 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 38.14 in | ✓ Conflicting sources — resolved · Calculated/inferred | Frigidaire measurement source — FRFG2011AV-104687233.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit38.14 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 35 in cabinet width + 2 * 1.57 in side clearance = 38.14 in Confidence label: high. Primary evidenceFrigidaire measurement source — FRFG2011AV-104687233.pdf Exact sheet cabinet width 35 in plus exact-model-linked manual side clearance 1.57 in at each side.Open original source ↗ All retained supporting links
Why this value was usedExact sheet cabinet width 35 in plus exact-model-linked manual side clearance 1.57 in at each side. Calculation or inference: 35 in cabinet width + 2 * 1.57 in side clearance = 38.14 in. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 71.54 in | ✓ Conflicting sources — resolved · Calculated/inferred | Frigidaire measurement source — FRFG2011AV-104687233.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit71.54 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 68 in hinge height + 3.54 in top clearance = 71.54 in Confidence label: high. Primary evidenceFrigidaire measurement source — FRFG2011AV-104687233.pdf Exact sheet hinge height 68 in plus exact-model-linked manual top clearance 3.54 in.Open original source ↗ All retained supporting links
Why this value was usedExact sheet hinge height 68 in plus exact-model-linked manual top clearance 3.54 in. Calculation or inference: 68 in hinge height + 3.54 in top clearance = 71.54 in. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 26.77 in | ✓ Verified — retained secondary source · Calculated/inferred | Frigidaire measurement source — FRFG2011AV-104687233.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit26.77 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24.8 in cabinet-only depth + 1.97 in rear clearance = 26.77 in Confidence label: high. Primary evidenceFrigidaire measurement source — FRFG2011AV-104687233.pdf Exact sheet cabinet depth 24.8 in plus exact-model-linked manual rear clearance 1.97 in.Open original source ↗ All retained supporting links
Why this value was usedExact sheet cabinet depth 24.8 in plus exact-model-linked manual rear clearance 1.97 in. Calculation or inference: 24.8 in cabinet-only depth + 1.97 in rear clearance = 26.77 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 1.57 in | ✓ Verified — retained secondary source | Frigidaire measurement source — A29913802en-January-2026-pdf.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit1.57 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire measurement source — A29913802en-January-2026-pdf.pdf Exact-model-linked January-2026 owner guide page 7 prints Sides 1.57 in (40 mm).Open original source ↗ All retained supporting links
Why this value was usedExact-model-linked January-2026 owner guide page 7 prints Sides 1.57 in (40 mm). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 1.57 in | ✓ Verified — retained secondary source | Frigidaire measurement source — A29913802en-January-2026-pdf.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit1.57 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire measurement source — A29913802en-January-2026-pdf.pdf Exact-model-linked January-2026 owner guide page 7 prints Sides 1.57 in (40 mm).Open original source ↗ All retained supporting links
Why this value was usedExact-model-linked January-2026 owner guide page 7 prints Sides 1.57 in (40 mm). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 3.54 in | ✓ Conflicting sources — resolved | Frigidaire measurement source — A29913802en-January-2026-pdf.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit3.54 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire measurement source — A29913802en-January-2026-pdf.pdf Exact-model-linked January-2026 owner guide page 7 prints Top 3.54 in (90 mm).Open original source ↗ All retained supporting links
Why this value was usedExact-model-linked January-2026 owner guide page 7 prints Top 3.54 in (90 mm). Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1.97 in | ✓ Conflicting sources — resolved | Frigidaire measurement source — A29913802en-January-2026-pdf.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit1.97 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire measurement source — A29913802en-January-2026-pdf.pdf Exact-model-linked January-2026 owner guide page 7 prints Back 1.97 in (50 mm).Open original source ↗ All retained supporting links
Why this value was usedExact-model-linked January-2026 owner guide page 7 prints Back 1.97 in (50 mm). Other evidence found
Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35 in | ✓ Verified — retained secondary source | Frigidaire installation document — 104687233.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 104687233.pdf Width of Cabinet 35"Open original source ↗ Why this value was usedWidth of Cabinet 35" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 38.14 in. Earlier retained values: 35 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact sheet cabinet width 35 in plus exact-model-linked manual side clearance 1.57 in at each side. Calculation or inference: 35 in cabinet width + 2 * 1.57 in side clearance = 38.14 in.
View source scope, location, and impact on fitSelected: 71.54 in. Earlier retained values: 68.375 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact sheet hinge height 68 in plus exact-model-linked manual top clearance 3.54 in. Calculation or inference: 68 in hinge height + 3.54 in top clearance = 71.54 in.
View source scope, location, and impact on fitSelected: 3.54 in. Earlier retained values: 0.375 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model-linked January-2026 owner guide page 7 prints Top 3.54 in (90 mm).
View source scope, location, and impact on fitSelected: 1.97 in. Earlier retained values: 2 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model-linked January-2026 owner guide page 7 prints Back 1.97 in (50 mm).
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: FRFG2011AV. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
7 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗www.homedepot.com · Web source · secondary model/source
Model numbers covered: FRFG2011AV. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Depth with doors open at 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: FRFG2011AV. Publication/revision date: Not recorded. Reviewed: 2026-09-11.
3 displayed measurements supported: Minimum cutout width; Minimum cutout height; Minimum cutout depth.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: FRFG2011AV. Publication/revision date: Not recorded. Reviewed: 2026-09-11.
4 displayed measurements supported: Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-11. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.