This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Single Door Refrigerator · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-09. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 27.75 in | ✓ Verified — retained secondary source | Frigidaire installation document — 106160604.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit27.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 106160604.pdf Width 27 3/4"Open original source ↗ Why this value was usedWidth 27 3/4" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 67.75 in | ✓ Verified — retained secondary source | Frigidaire measurement source — Frigidaire_FRAE1626AW_All_Refrigerator_Frigidaire_FRAE1626AW.html www.canadianappliance.ca | Retained specification excerpt: Exact-model specification: Height to Top of Case 67 3/4 inches. | |
Value used by ExactFit67.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceFrigidaire measurement source — Frigidaire_FRAE1626AW_All_Refrigerator_Frigidaire_FRAE1626AW.html Exact-model specification: Height to Top of Case 67 3/4 inches.Open original source ↗ Why this value was usedExact-model specification: Height to Top of Case 67 3/4 inches. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 67.75 in | ✓ Verified — retained secondary source | Frigidaire installation document — 106160604.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit67.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 106160604.pdf Height With Hinge 67 3/4"Open original source ↗ Why this value was usedHeight With Hinge 67 3/4" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 26.625 in | ✓ Verified — retained secondary source | Frigidaire installation document — 106160604.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit26.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 106160604.pdf Depth of Cabinet 26 5/8"Open original source ↗ Why this value was usedDepth of Cabinet 26 5/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 29.125 in | ✓ Verified — retained secondary source | Frigidaire installation document — 106160604.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit29.125 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 106160604.pdf Depth With Door 29 1/8"Open original source ↗ Why this value was usedDepth With Door 29 1/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 29.125 in | ✓ Verified — retained secondary source | Frigidaire installation document — 106160604.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit29.125 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 106160604.pdf Depth With Door and Handle 29 1/8"Open original source ↗ Why this value was usedDepth With Door and Handle 29 1/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 54 in | ✓ Verified — retained secondary source | Frigidaire measurement source — 339414048 www.homedepot.com | Retained specification excerpt: Exact-model specification: Depth With Door Open 90 Degrees 54 in. | |
Value used by ExactFit54 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire measurement source — 339414048 Exact-model specification: Depth With Door Open 90 Degrees 54 in.Open original source ↗ Why this value was usedExact-model specification: Depth With Door Open 90 Degrees 54 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 35.75 in | ✓ Conflicting sources — resolved · Calculated/inferred | Frigidaire measurement source — 106160606.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit35.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: case_width_in + 2 * side_ventilation_clearance_in Confidence label: high. Calculation inputs: Left-side ventilation clearance; Cabinet case width; Primary evidenceFrigidaire measurement source — 106160606.pdf Frigidaire family installation-envelope calculation: case_width_in=27.75, side_ventilation_clearance_in=4; result=35.75 in. Product operand source: 106160604.pdf.Open original source ↗ Why this value was usedFrigidaire family installation-envelope calculation: case_width_in=27.75, side_ventilation_clearance_in=4; result=35.75 in. Product operand source: 106160604.pdf. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 71.75 in | ✓ Verified — retained secondary source · Calculated/inferred | Frigidaire measurement source — 106160606.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit71.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: height_hinge_in + top_clearance_in Confidence label: high. Calculation inputs: Height with hinge / controlling height; Top clearance; Primary evidenceFrigidaire measurement source — 106160606.pdf Frigidaire family installation-envelope calculation: height_hinge_in=67.75, top_clearance_in=4; result=71.75 in. Product operand source: 106160604.pdf.Open original source ↗ Why this value was usedFrigidaire family installation-envelope calculation: height_hinge_in=67.75, top_clearance_in=4; result=71.75 in. Product operand source: 106160604.pdf. Calculation or inference: height_hinge_in + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 30.625 in | ✓ Verified — retained secondary source · Calculated/inferred | Frigidaire measurement source — 106160606.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit30.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: high. Calculation inputs: Depth without door; Rear clearance; Primary evidenceFrigidaire measurement source — 106160606.pdf Frigidaire family installation-envelope calculation: depth_case_only_in=26.625, rear_clearance_in=4; result=30.625 in. Product operand source: 106160604.pdf.Open original source ↗ Why this value was usedFrigidaire family installation-envelope calculation: depth_case_only_in=26.625, rear_clearance_in=4; result=30.625 in. Product operand source: 106160604.pdf. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 4 in | ✓ Verified — retained secondary source | Frigidaire installation document — 106160606.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit4 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 106160606.pdf Allow the following clearances for ease of installation, proper air circulations, and plumbing and electrical connections: Sides, Top & Back 4" (101 mm)Open original source ↗ Why this value was usedAllow the following clearances for ease of installation, proper air circulations, and plumbing and electrical connections: Sides, Top & Back 4" (101 mm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 4 in | ✓ Verified — retained secondary source | Frigidaire installation document — 106160606.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit4 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 106160606.pdf Allow the following clearances for ease of installation, proper air circulations, and plumbing and electrical connections: Sides, Top & Back 4" (101 mm)Open original source ↗ Why this value was usedAllow the following clearances for ease of installation, proper air circulations, and plumbing and electrical connections: Sides, Top & Back 4" (101 mm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 4 in | ✓ Verified — retained secondary source | Frigidaire installation document — 106160606.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit4 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 106160606.pdf Allow the following clearances for ease of installation, proper air circulations, and plumbing and electrical connections: Sides, Top & Back 4" (101 mm)Open original source ↗ Why this value was usedAllow the following clearances for ease of installation, proper air circulations, and plumbing and electrical connections: Sides, Top & Back 4" (101 mm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 4 in | ✓ Verified — retained secondary source | Frigidaire installation document — 106160606.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit4 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 106160606.pdf Allow the following clearances for ease of installation, proper air circulations, and plumbing and electrical connections: Sides, Top & Back 4" (101 mm)Open original source ↗ Why this value was usedAllow the following clearances for ease of installation, proper air circulations, and plumbing and electrical connections: Sides, Top & Back 4" (101 mm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 27.75 in | ✓ Verified — retained secondary source | Frigidaire installation document — 106160604.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit27.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire installation document — 106160604.pdf Width 27 3/4"Open original source ↗ Why this value was usedWidth 27 3/4" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 35.75 in. Earlier retained values: 28.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Frigidaire family installation-envelope calculation: case_width_in=27.75, side_ventilation_clearance_in=4; result=35.75 in. Product operand source: 106160604.pdf. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: FRAE1626AW. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
6 displayed measurements supported: Overall width; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗www.canadianappliance.ca · Web source · secondary model/source
Model numbers covered: FRAE1626AW. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Cabinet height.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗www.homedepot.com · Web source · secondary model/source
Model numbers covered: FRAE1626AW. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Depth with doors open at 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: FRAE1626AW. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
7 displayed measurements supported: Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-09. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.