This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 30 in | ✓ Secondary source only | Frigidaire FFHT2022AS Product Specifications Sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit30 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2022AS Product Specifications Sheet Width 30"Open original source ↗ Why this value was usedWidth 30" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 65.875 in | ✓ Secondary source only | Frigidaire FFHT2022AS Product Specifications Sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit65.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2022AS Product Specifications Sheet Height Without Hinge 65 7/8"Open original source ↗ Why this value was usedHeight Without Hinge 65 7/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 66.375 in | ✓ Secondary source only | Frigidaire FFHT2022AS Product Specifications Sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit66.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2022AS Product Specifications Sheet Height With Hinge 66 3/8"Open original source ↗ Why this value was usedHeight With Hinge 66 3/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 28.25 in | ✓ Secondary source only | Frigidaire FFHT2022AS Product Specifications Sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit28.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2022AS Product Specifications Sheet Depth of Cabinet 28 1/4"Open original source ↗ Why this value was usedDepth of Cabinet 28 1/4" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 32 in | ✓ Secondary source only | Frigidaire FFHT2022AS Product Specifications Sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit32 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2022AS Product Specifications Sheet Depth With Door 32"Open original source ↗ Why this value was usedDepth With Door 32" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 32 in | ✓ Secondary source only | Frigidaire FFHT2022AS Product Specifications Sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit32 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2022AS Product Specifications Sheet Depth With Door and Handle 32"Open original source ↗ Why this value was usedDepth With Door and Handle 32" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 58.625 in | ✓ Secondary source only | Frigidaire FFHT2022AS Product Specifications Sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit58.625 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2022AS Product Specifications Sheet Depth With Door 90° Open 58 5/8"Open original source ↗ Why this value was usedDepth With Door 90° Open 58 5/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 30.75 in | ✓ Secondary source only · Calculated/inferred | Frigidaire FFHT2022AS Product Specifications Sheet assets.skulytics.io | Retained specification excerpt: Derived minimum opening width 30.75 in from product width 30.0 in and explicit 0.375 in clearance on | |
Value used by ExactFit30.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 30.0 + 2 * 0.375 Confidence label: medium. Primary evidenceFrigidaire FFHT2022AS Product Specifications Sheet Derived minimum opening width 30.75 in from product width 30.0 in and explicit 0.375 in clearance on each side.Open original source ↗ Why this value was usedDerived minimum opening width 30.75 in from product width 30.0 in and explicit 0.375 in clearance on each side. Calculation or inference: max(case width, width doors closed) + 2 * explicit side clearance = 30.0 + 2 * 0.375. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 66.75 in | ✓ Secondary source only · Calculated/inferred | Frigidaire FFHT2022AS Installation Instructions assets.skulytics.io | Page 1 | |
Value used by ExactFit66.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceFrigidaire FFHT2022AS Installation Instructions Minimum opening height derived from highest stored appliance endpoint 66.375 in plus documented top clearance 0.375 in.Open original source ↗ Why this value was usedMinimum opening height derived from highest stored appliance endpoint 66.375 in plus documented top clearance 0.375 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 29.25 in | ✓ Secondary source only · Calculated/inferred | Frigidaire FFHT2022AS Installation Instructions assets.skulytics.io | Page 1 | |
Value used by ExactFit29.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceFrigidaire FFHT2022AS Installation Instructions Minimum opening depth derived from case-only depth 28.25 in plus documented rear clearance 1.0 in.Open original source ↗ Why this value was usedMinimum opening depth derived from case-only depth 28.25 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.375 in | ✓ Secondary source only | Frigidaire FFHT2022AS Installation Instructions assets.skulytics.io | Page 1 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2022AS Installation Instructions air circulation, and plumbing and electrical connections: | Sides & Top: 3/8 in. | Rear: 1 in. | deterministic pattern: installation_sidesOpen original source ↗ Why this value was usedair circulation, and plumbing and electrical connections: | Sides & Top: 3/8 in. | Rear: 1 in. | deterministic pattern: installation_sides Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.375 in | ✓ Secondary source only | Frigidaire FFHT2022AS Installation Instructions assets.skulytics.io | Page 1 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2022AS Installation Instructions air circulation, and plumbing and electrical connections: | Sides & Top: 3/8 in. | Rear: 1 in. | deterministic pattern: installation_sidesOpen original source ↗ Why this value was usedair circulation, and plumbing and electrical connections: | Sides & Top: 3/8 in. | Rear: 1 in. | deterministic pattern: installation_sides Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.375 in | ✓ Secondary source only | Frigidaire FFHT2022AS Installation Instructions assets.skulytics.io | Page 1 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2022AS Installation Instructions air circulation, and plumbing and electrical connections: | Sides & Top: 3/8 in. | Rear: 1 in. | deterministic pattern: installation_sidesOpen original source ↗ Why this value was usedair circulation, and plumbing and electrical connections: | Sides & Top: 3/8 in. | Rear: 1 in. | deterministic pattern: installation_sides Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Secondary source only | Frigidaire FFHT2022AS Installation Instructions assets.skulytics.io | Page 1 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2022AS Installation Instructions air circulation, and plumbing and electrical connections: | Sides & Top: 3/8 in. | Rear: 1 in. | deterministic pattern: installation_sidesOpen original source ↗ Why this value was usedair circulation, and plumbing and electrical connections: | Sides & Top: 3/8 in. | Rear: 1 in. | deterministic pattern: installation_sides Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | Unknown | ? Not found · Calculated/inferred | Frigidaire FFHT2022AS Installation Instructions assets.skulytics.io | Page 1 | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: hinge-side baseline = documented side ventilation clearance Confidence label: medium. Primary evidenceFrigidaire FFHT2022AS Installation Instructions air circulation, and plumbing and electrical connections: | Sides & Top: 3/8 in. | Rear: 1 in. | deterministic pattern: installation_sides Hinge-side wall note is conditional and gives no separate numeric minimum; this value is the documented side-clearance baseline.Open original source ↗ Why this value was usedA low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement. Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 30 in | ✓ Secondary source only | Frigidaire FFHT2022AS Product Specifications Sheet assets.skulytics.io | Page 1 | |
Value used by ExactFit30 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFrigidaire FFHT2022AS Product Specifications Sheet Width of Cabinet 30"Open original source ↗ Why this value was usedWidth of Cabinet 30" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | 0.375 in | ✓ Secondary source only | Frigidaire FFHT2022AS Installation Instructions assets.skulytics.io | Page 1 | |
Value used by ExactFit0.375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceFrigidaire FFHT2022AS Installation Instructions air circulation, and plumbing and electrical connections: | Sides & Top: 3/8 in. | Rear: 1 in. | deterministic pattern: installation_sidesOpen original source ↗ Why this value was usedair circulation, and plumbing and electrical connections: | Sides & Top: 3/8 in. | Rear: 1 in. | deterministic pattern: installation_sides Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Not found for safe fit use. Sources retained: 103505768.pdf. Related-model record: FFHT2022AS.
A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Product Specifications Sheet · secondary model/source
Model numbers covered: FFHT2022AS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
8 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Product Specifications Sheet · secondary model/source
Model numbers covered: FFHT2022AS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Minimum cutout width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Installation Instructions · secondary model/source
Model numbers covered: FFHT2022AS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
8 displayed measurements supported: Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Hinge-side wall clearance; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.