Measurement evidence for Frigidaire FFHT1822UB

Value used by ExactFit

27.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 74528464.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width 27 7/8"

Why this value was used

Width 27 7/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

66.2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 74528464.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height Without Hinge 66 2/10"

Why this value was used

Height Without Hinge 66 2/10"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

66.9375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 74528464.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height With Hinge 66 15/16"

Why this value was used

Height With Hinge 66 15/16"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

27.6 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 74528464.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth of Cabinet 27 6/10"

Why this value was used

Depth of Cabinet 27 6/10"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

30.8 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 74528464.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door 30 8/10"

Why this value was used

Depth With Door 30 8/10"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30.8 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 74528464.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door and Handle 30 8/10"

Why this value was used

Depth With Door and Handle 30 8/10"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

56.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 74528464.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door 90° Open 56 1/2"

Why this value was used

Depth With Door 90° Open 56 1/2"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

28.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case_width_in + 2 * side_ventilation_clearance_in

Confidence label: high.

Calculation inputs: Left-side ventilation clearance; Cabinet case width;

Primary evidence

Frigidaire measurement source — side gap from the maker's document
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Frigidaire family installation-envelope calculation: case_width_in=27.875, side_ventilation_clearanc
Reviewed: 2026-09-09

Frigidaire family installation-envelope calculation: case_width_in=27.875, side_ventilation_clearance_in=0.375; result=28.625 in. Product operand source: 74528464.pdf.

Why this value was used

Frigidaire family installation-envelope calculation: case_width_in=27.875, side_ventilation_clearance_in=0.375; result=28.625 in. Product operand source: 74528464.pdf. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

67.3125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: height_hinge_in + top_clearance_in

Confidence label: high.

Calculation inputs: Height with hinge / controlling height; Top clearance;

Primary evidence

Frigidaire measurement source — 74528467.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-09

Frigidaire family installation-envelope calculation: height_hinge_in=66.9375, top_clearance_in=0.375; result=67.3125 in. Product operand source: 74528464.pdf.

Why this value was used

Frigidaire family installation-envelope calculation: height_hinge_in=66.9375, top_clearance_in=0.375; result=67.3125 in. Product operand source: 74528464.pdf. Calculation or inference: height_hinge_in + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.6 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: high.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Frigidaire measurement source — 74528467.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-09

Frigidaire family installation-envelope calculation: depth_case_only_in=27.6, rear_clearance_in=2; result=29.6 in. Product operand source: 74528464.pdf.

Why this value was used

Frigidaire family installation-envelope calculation: depth_case_only_in=27.6, rear_clearance_in=2; result=29.6 in. Product operand source: 74528464.pdf. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire measurement source — 74528467.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-10-29

The document this model's measurements come from states: "air circu­ lation, and plumbing and electrical connections: Sides & Top ⅜" Back 2" To level the cabinet using the."

Why this value was used

The document this model's measurements come from states: "air circu­ lation, and plumbing and electrical connections: Sides & Top ⅜" Back 2" To level the cabinet using the."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire measurement source — 74528467.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-10-29

The document this model's measurements come from states: "air circu­ lation, and plumbing and electrical connections: Sides & Top ⅜" Back 2" To level the cabinet using the."

Why this value was used

The document this model's measurements come from states: "air circu­ lation, and plumbing and electrical connections: Sides & Top ⅜" Back 2" To level the cabinet using the."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 74528467.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-09

Allow the following clearances for ease of installation, proper air circu­ lation, and plumbing and electrical connections: Sides & Top ⅜" Back 2" To level the cabinet using the front leveling feet: • Lower the leveling feet on each side clockwise until they contact the floor. Lower Raise • Use the leveling feet (located on the front) ensure that all 4 corners of the unit are resting firmly on a solid floor. Turn the leveling feet clockwise to retract the feet and counterclockwise to extend the

Why this value was used

Allow the following clearances for ease of installation, proper air circu­ lation, and plumbing and electrical connections: Sides & Top ⅜" Back 2" To level the cabinet using the front leveling feet: • Lower the leveling feet on each side clockwise until they contact the floor. Lower Raise • Use the leveling feet (located on the front) ensure that all 4 corners of the unit are resting firmly on a solid floor. Turn the leveling feet clockwise to retract the feet and counterclockwise to extend the

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 74528467.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-05

Allow the following clearances for ease of installation, proper air circu­ lation, and plumbing and electrical connections: Sides & Top ⅜" Back 2" To level the cabinet using the front leveling feet: • Lower the leveling feet on each side clockwise until they contact the floor. Lower Raise • Use the leveling feet (located on the front) ensure that all 4 corners of the unit are resting firmly on a solid floor. Turn the leveling feet clockwise to retract the feet and counterclockwise to extend the

Why this value was used

Allow the following clearances for ease of installation, proper air circu­ lation, and plumbing and electrical connections: Sides & Top ⅜" Back 2" To level the cabinet using the front leveling feet: • Lower the leveling feet on each side clockwise until they contact the floor. Lower Raise • Use the leveling feet (located on the front) ensure that all 4 corners of the unit are resting firmly on a solid floor. Turn the leveling feet clockwise to retract the feet and counterclockwise to extend the

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

27.875 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 74528464.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width of Cabinet 27 7/8"

Why this value was used

Width of Cabinet 27 7/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.