This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-29. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire installation document — 74623176.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire installation document — 74623176.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire installation document — 74623176.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire installation document — 74623176.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire installation document — 74623176.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire installation document — 74623176.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire installation document — 74623176.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Frigidaire measurement source — side gap from the maker's document assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Frigidaire family installation-envelope calculation: case_width_in=30, side_ventilation_clearance_in Reviewed: 2026-09-09
Frigidaire family installation-envelope calculation: case_width_in=30, side_ventilation_clearance_in=0.375; result=30.75 in. Product operand source: 74623176.pdf.
Frigidaire family installation-envelope calculation: case_width_in=30, side_ventilation_clearance_in=0.375; result=30.75 in. Product operand source: 74623176.pdf. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Frigidaire family installation-envelope calculation: height_hinge_in=66.375, top_clearance_in=0.375; result=66.75 in. Product operand source: 74623176.pdf. Calculation or inference: height_hinge_in + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Frigidaire family installation-envelope calculation: depth_case_only_in=26.625, rear_clearance_in=1; result=27.625 in. Product operand source: 74623176.pdf. Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire measurement source — 103504009.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-10-29
The document this model's measurements come from states: "air circulation, and plumbing and electrical connections: • Sides and top 3/8" (9.5 mm) • Back 1" (25.4 mm) NOTE If y."
The document this model's measurements come from states: "air circulation, and plumbing and electrical connections: • Sides and top 3/8" (9.5 mm) • Back 1" (25.4 mm) NOTE If y."
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire measurement source — 103504009.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-10-29
The document this model's measurements come from states: "air circulation, and plumbing and electrical connections: • Sides and top 3/8" (9.5 mm) • Back 1" (25.4 mm) NOTE If y."
The document this model's measurements come from states: "air circulation, and plumbing and electrical connections: • Sides and top 3/8" (9.5 mm) • Back 1" (25.4 mm) NOTE If y."
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire installation document — 103504009.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-09-09
Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: • Sides and top 3/8" (9.5 mm) • Back 1" (25.4 mm) NOTE If you place the appliance with the door hinge side against a wall, you may have to allow additional space so the door can be open wider. 3.6 Cabinet leveling and door alignment Guidelines for final positioning of appliance: • All 4 corners of the cabinet must rest firmly on the floor. • The cabinet should be level at th
Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: • Sides and top 3/8" (9.5 mm) • Back 1" (25.4 mm) NOTE If you place the appliance with the door hinge side against a wall, you may have to allow additional space so the door can be open wider. 3.6 Cabinet leveling and door alignment Guidelines for final positioning of appliance: • All 4 corners of the cabinet must rest firmly on the floor. • The cabinet should be level at th
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire installation document — 103504009.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-09-09
Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: • Sides and top 3/8" (9.5 mm) • Back 1" (25.4 mm) NOTE If you place the appliance with the door hinge side against a wall, you may have to allow additional space so the door can be open wider. 3.6 Cabinet leveling and door alignment Guidelines for final positioning of appliance: • All 4 corners of the cabinet must rest firmly on the floor. • The cabinet should be level at th
Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: • Sides and top 3/8" (9.5 mm) • Back 1" (25.4 mm) NOTE If you place the appliance with the door hinge side against a wall, you may have to allow additional space so the door can be open wider. 3.6 Cabinet leveling and door alignment Guidelines for final positioning of appliance: • All 4 corners of the cabinet must rest firmly on the floor. • The cabinet should be level at th
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization:
Confidence label: high.
Primary evidence
Frigidaire measurement source — 74623176.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-17
Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees (text also gives a fully open figure)). Manufacturer installation diagram: when adjacent to a wall, 20 in minimum is recommended for complete crisper access; absolute 3 in minimum clearance allows 90-degree door swing with restricted removal.
Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees (text also gives a fully open figure)). Manufacturer installation diagram: when adjacent to a wall, 20 in minimum is recommended for complete crisper access; absolute 3 in minimum clearance allows 90-degree door swing with restricted removal.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Frigidaire measurement source — 74623176.pdf Publisher not recorded
Page 2
Value used by ExactFit
20 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire measurement source — 74623176.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-26
When installing next to a wall, cabinet or other appliance that extends beyond the front edge of the unit, 20 in minimum clearance is recommended for the optimum 140 degree door swing, complete crisper access and removal. The stored 90 degree figure is the absolute minimum.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
When installing next to a wall, cabinet or other appliance that extends beyond the front edge of the unit, 20 in minimum clearance is recommended for the optimum 140 degree door swing, complete crisper access and removal. The stored 90 degree figure is the absolute minimum.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Frigidaire installation document — 74623176.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Model numbers covered: FFHT1814WB. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
10 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Wall clearance for door open to 90°; Wall clearance for fully open door; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-10-29. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
