Measurement evidence for Frigidaire FFHT1425VB

Value used by ExactFit

27.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 104457176.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width 27 5/8"

Why this value was used

Width 27 5/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

59.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 104457176.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height Without Hinge 59 7/8"

Why this value was used

Height Without Hinge 59 7/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

60.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 104457176.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height With Hinge 60 1/2"

Why this value was used

Height With Hinge 60 1/2"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 104457176.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth of Cabinet 25 1/4"

Why this value was used

Depth of Cabinet 25 1/4"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.375 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 104457176.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door 29 3/8"

Why this value was used

Depth With Door 29 3/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.375 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 104457176.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door and Handle 29 3/8"

Why this value was used

Depth With Door and Handle 29 3/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

53.625 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 104457176.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth With Door 90° Open 53 5/8"

Why this value was used

Depth With Door 90° Open 53 5/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30.765 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case_width_in + 2 * side_ventilation_clearance_in

Confidence label: high.

Calculation inputs: Left-side ventilation clearance; Cabinet case width;

Primary evidence

Frigidaire measurement source — 104457178.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

Frigidaire family installation-envelope calculation: case_width_in=27.625, side_ventilation_clearance_in=1.57; result=30.765 in. Product operand source: 104457176.pdf.

Why this value was used

Frigidaire family installation-envelope calculation: case_width_in=27.625, side_ventilation_clearance_in=1.57; result=30.765 in. Product operand source: 104457176.pdf. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in.

Other evidence found

• 28.375 in — superseded

  An earlier brand-wide assumption (no document for this model); location not retained. Model scope: not separately recorded. Raw value: Derived minimum opening width 28.375 in from product width 27.625 in and explicit 0.375 in clearance on each side.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

64.44 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: height_hinge_in + top_clearance_in

Confidence label: high.

Calculation inputs: Height with hinge / controlling height; Top clearance;

Primary evidence

Frigidaire measurement source — 104457178.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

Frigidaire family installation-envelope calculation: height_hinge_in=60.5, top_clearance_in=3.94; result=64.44 in. Product operand source: 104457176.pdf.

Why this value was used

Frigidaire family installation-envelope calculation: height_hinge_in=60.5, top_clearance_in=3.94; result=64.44 in. Product operand source: 104457176.pdf. Calculation or inference: height_hinge_in + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26.43 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: high.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Frigidaire measurement source — 104457178.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

Frigidaire family installation-envelope calculation: depth_case_only_in=25.25, rear_clearance_in=1.18; result=26.43 in. Product operand source: 104457176.pdf.

Why this value was used

Frigidaire family installation-envelope calculation: depth_case_only_in=25.25, rear_clearance_in=1.18; result=26.43 in. Product operand source: 104457176.pdf. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1.57 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 104457178.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Top 3.94 in 100mm Sides 1.57 in 40 mm Back 1.18 in 30 mm NOTE Information about cabinetry construc­ tion for your new appliance is available for contractors. Call 1-877-435-3287. CAUTION Room temperatures below 55°F (13°C) or above 110°F (43°C) will impair cooling ability of your refrigerator’s compressor. Tools Necessary: Phillips Head or Quadrex Head Screwdriver Socket Wre

Why this value was used

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Top 3.94 in 100mm Sides 1.57 in 40 mm Back 1.18 in 30 mm NOTE Information about cabinetry construc­ tion for your new appliance is available for contractors. Call 1-877-435-3287. CAUTION Room temperatures below 55°F (13°C) or above 110°F (43°C) will impair cooling ability of your refrigerator’s compressor. Tools Necessary: Phillips Head or Quadrex Head Screwdriver Socket Wre

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1.57 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 104457178.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Top 3.94 in 100mm Sides 1.57 in 40 mm Back 1.18 in 30 mm NOTE Information about cabinetry construc­ tion for your new appliance is available for contractors. Call 1-877-435-3287. CAUTION Room temperatures below 55°F (13°C) or above 110°F (43°C) will impair cooling ability of your refrigerator’s compressor. Tools Necessary: Phillips Head or Quadrex Head Screwdriver Socket Wre

Why this value was used

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Top 3.94 in 100mm Sides 1.57 in 40 mm Back 1.18 in 30 mm NOTE Information about cabinetry construc­ tion for your new appliance is available for contractors. Call 1-877-435-3287. CAUTION Room temperatures below 55°F (13°C) or above 110°F (43°C) will impair cooling ability of your refrigerator’s compressor. Tools Necessary: Phillips Head or Quadrex Head Screwdriver Socket Wre

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.94 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 104457178.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Top 3.94 in 100mm Sides 1.57 in 40 mm Back 1.18 in 30 mm NOTE Information about cabinetry construc­ tion for your new appliance is available for contractors. Call 1-877-435-3287. CAUTION Room temperatures below 55°F (13°C) or above 110°F (43°C) will impair cooling ability of your refrigerator’s compressor. Tools Necessary: Phillips Head or Quadrex Head Screwdriver Socket Wre

Why this value was used

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Top 3.94 in 100mm Sides 1.57 in 40 mm Back 1.18 in 30 mm NOTE Information about cabinetry construc­ tion for your new appliance is available for contractors. Call 1-877-435-3287. CAUTION Room temperatures below 55°F (13°C) or above 110°F (43°C) will impair cooling ability of your refrigerator’s compressor. Tools Necessary: Phillips Head or Quadrex Head Screwdriver Socket Wre

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1.18 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 104457178.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Top 3.94 in 100mm Sides 1.57 in 40 mm Back 1.18 in 30 mm NOTE Information about cabinetry construc­ tion for your new appliance is available for contractors. Call 1-877-435-3287. CAUTION Room temperatures below 55°F (13°C) or above 110°F (43°C) will impair cooling ability of your refrigerator’s compressor. Tools Necessary: Phillips Head or Quadrex Head Screwdriver Socket Wre

Why this value was used

Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections: Top 3.94 in 100mm Sides 1.57 in 40 mm Back 1.18 in 30 mm NOTE Information about cabinetry construc­ tion for your new appliance is available for contractors. Call 1-877-435-3287. CAUTION Room temperatures below 55°F (13°C) or above 110°F (43°C) will impair cooling ability of your refrigerator’s compressor. Tools Necessary: Phillips Head or Quadrex Head Screwdriver Socket Wre

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Frigidaire measurement source — FFHT1425VW_specification-sheet-french.pdf
assets.skulytics.io · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees (text also gives a fully open figure)). The visually reviewed manufacturer planning diagram states: when adjacent to a wall, cabinet, or other appliance extending beyond the front edge, 20 in is recommended for the optimum 140-degree swing and complete crisper access; an absolute 3 in minimum clearance will ONLY allow a 90-degree door swing with limited crisper access and restricted removal.

Why this value was used

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees (text also gives a fully open figure)). The visually reviewed manufacturer planning diagram states: when adjacent to a wall, cabinet, or other appliance extending beyond the front edge, 20 in is recommended for the optimum 140-degree swing and complete crisper access; an absolute 3 in minimum clearance will ONLY allow a 90-degree door swing with limited crisper access and restricted removal.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

20 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire measurement source — official-planning-sheet-07-21-fr.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-13

Installation drawing: 20" recommended for the optimum 140° door swing, complete crisper access and shelf removal (same Frigidaire note as earlier batches).

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Installation drawing: 20" recommended for the optimum 140° door swing, complete crisper access and shelf removal (same Frigidaire note as earlier batches).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

27.625 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Frigidaire installation document — 104457176.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width of Cabinet 27 5/8"

Why this value was used

Width of Cabinet 27 5/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.