This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Side-by-Side · Counter-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-22. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 32.9 in | ? Verified — finalized database measurement | Forno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Publisher not recorded | Page 1 | |
Value used by ExactFit32.9 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceForno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Forno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.1 front view width 32.9" (836mm), doors closed. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedForno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.1 front view width 32.9" (836mm), doors closed. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 70.14 in | ? Verified — finalized database measurement | Forno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Publisher not recorded | Page 1 | |
Value used by ExactFit70.14 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceForno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Forno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.1 front view overall height 70.14" (1781.5mm). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedForno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.1 front view overall height 70.14" (1781.5mm). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 21.42 in | ? Verified — finalized database measurement | Forno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Publisher not recorded | Page 1 | |
Value used by ExactFit21.42 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceForno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Forno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.1 side view cabinet depth 21.42" (544mm). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedForno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.1 side view cabinet depth 21.42" (544mm). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 24.67 in | ? Verified — finalized database measurement | Forno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Publisher not recorded | Page 1 | |
Value used by ExactFit24.67 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceForno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Forno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.1 side view depth to door front 24.67" (626.62mm). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedForno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.1 side view depth to door front 24.67" (626.62mm). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 27.42 in | ? Verified — finalized database measurement | Forno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Publisher not recorded | Page 1 | |
Value used by ExactFit27.42 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceForno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Forno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.1 side view depth including handles 27.42" (696.47mm). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedForno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.1 side view depth including handles 27.42" (696.47mm). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 40.19 in | ? Verified — finalized database measurement | Forno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Publisher not recorded | Page 1 | |
Value used by ExactFit40.19 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceForno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Forno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.1 plan view, doors at 90 deg: depth 40.19" (1020.7mm). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedForno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.1 plan view, doors at 90 deg: depth 40.19" (1020.7mm). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 33.9 in | ? Verified — finalized database measurement | Forno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit33.9 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceForno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Forno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.2 Cutout Dimensions: width 33.9" (861.06mm). Equals 32.9 in + 2 x 1/2 in. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedForno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.2 Cutout Dimensions: width 33.9" (861.06mm). Equals 32.9 in + 2 x 1/2 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 71.14 in | ? Verified — finalized database measurement | Forno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit71.14 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceForno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Forno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.2 Cutout Dimensions: height 71.14" (1806.96mm). Equals 70.14 in + 1 in. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedForno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.2 Cutout Dimensions: height 71.14" (1806.96mm). Equals 70.14 in + 1 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 24.42 in | ? Verified — finalized database measurement | Forno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit24.42 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceForno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Forno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.2 Cutout Dimensions: depth 24.42" (720.27mm as printed). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedForno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.2 Cutout Dimensions: depth 24.42" (720.27mm as printed). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.5 in | ? Verified — finalized database measurement | Forno measurement source — c4e87e3cf9ff7f76680375247f51a7504fcf89604c591bfcf0d80c8d3f9b6174.pdf Publisher not recorded | Page 10 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceForno measurement source — c4e87e3cf9ff7f76680375247f51a7504fcf89604c591bfcf0d80c8d3f9b6174.pdf Forno instruction manual for FFRBI1805-33BLK/FFRBI1805-33WHT, p.10: "ALLOW 3-5 INCHES OF SPACE BETWEEN THE BACK OF THE APPLIANCE AND THE WALL AS WELL AS A MINIMUM OF ½" (HALF INCH) AT EACH SIDE OF THE UNIT AND ONE (1) INCH AT THE TOP". The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedForno instruction manual for FFRBI1805-33BLK/FFRBI1805-33WHT, p.10: "ALLOW 3-5 INCHES OF SPACE BETWEEN THE BACK OF THE APPLIANCE AND THE WALL AS WELL AS A MINIMUM OF ½" (HALF INCH) AT EACH SIDE OF THE UNIT AND ONE (1) INCH AT THE TOP". Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.5 in | ? Verified — finalized database measurement | Forno measurement source — c4e87e3cf9ff7f76680375247f51a7504fcf89604c591bfcf0d80c8d3f9b6174.pdf Publisher not recorded | Page 10 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceForno measurement source — c4e87e3cf9ff7f76680375247f51a7504fcf89604c591bfcf0d80c8d3f9b6174.pdf Forno instruction manual for FFRBI1805-33BLK/FFRBI1805-33WHT, p.10: "ALLOW 3-5 INCHES OF SPACE BETWEEN THE BACK OF THE APPLIANCE AND THE WALL AS WELL AS A MINIMUM OF ½" (HALF INCH) AT EACH SIDE OF THE UNIT AND ONE (1) INCH AT THE TOP". The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedForno instruction manual for FFRBI1805-33BLK/FFRBI1805-33WHT, p.10: "ALLOW 3-5 INCHES OF SPACE BETWEEN THE BACK OF THE APPLIANCE AND THE WALL AS WELL AS A MINIMUM OF ½" (HALF INCH) AT EACH SIDE OF THE UNIT AND ONE (1) INCH AT THE TOP". Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 1 in | ? Verified — finalized database measurement | Forno measurement source — c4e87e3cf9ff7f76680375247f51a7504fcf89604c591bfcf0d80c8d3f9b6174.pdf Publisher not recorded | Page 10 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceForno measurement source — c4e87e3cf9ff7f76680375247f51a7504fcf89604c591bfcf0d80c8d3f9b6174.pdf Forno instruction manual for FFRBI1805-33BLK/FFRBI1805-33WHT, p.10: "ONE (1) INCH AT THE TOP"; Minimum Space Allowances: One (1) inch. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedForno instruction manual for FFRBI1805-33BLK/FFRBI1805-33WHT, p.10: "ONE (1) INCH AT THE TOP"; Minimum Space Allowances: One (1) inch. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 3 in | ? Verified — finalized database measurement | Forno measurement source — c4e87e3cf9ff7f76680375247f51a7504fcf89604c591bfcf0d80c8d3f9b6174.pdf Publisher not recorded | Page 10 | |
Value used by ExactFit3 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceForno measurement source — c4e87e3cf9ff7f76680375247f51a7504fcf89604c591bfcf0d80c8d3f9b6174.pdf Forno instruction manual for FFRBI1805-33BLK/FFRBI1805-33WHT, p.10: "Three to Five (3 - 5) inches at the back"; the minimum, 3 in, is stored. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedForno instruction manual for FFRBI1805-33BLK/FFRBI1805-33WHT, p.10: "Three to Five (3 - 5) inches at the back"; the minimum, 3 in, is stored. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 32.9 in | ? Verified — finalized database measurement | Forno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Publisher not recorded | Page 1 | |
Value used by ExactFit32.9 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceForno measurement source — f5fee8f6d2f969abbfc146da9806d7aed7132f7e877231c1767c0df58a35ccc3.pdf Forno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.1 front view width 32.9" (836mm). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedForno Product & Cutout Dimensions sheet (2023), Model: FFRBI1805-33SB | FFRBI1805-33BLK | FFRBI1805-33WTH, p.1 front view width 32.9" (836mm). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-10-22.
10 displayed measurements supported: Overall width; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Cabinet case width.
Availability: retained review record; original URL unavailable in the record.
Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-10-22.
4 displayed measurements supported: Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL unavailable in the record.
Evidence reflects the sources reviewed on 2026-10-22. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.