Measurement evidence for Fisher and Paykel RS36A80J1N

Value used by ExactFit

35.6875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 82594863.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RS36A80J1N: width_doors_closed_in = 35.6875 in

Why this value was used

Reviewed manufacturer dimensions for RS36A80J1N: width_doors_closed_in = 35.6875 in

Other evidence found

• 35.0625 in — superseded

  Document 82594859.pdf; page 1. Model scope: not separately recorded. Raw value: Width 35 1/16". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

79.8125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 82594863.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RS36A80J1N: height_case_in = 79.8125 in

Why this value was used

Reviewed manufacturer dimensions for RS36A80J1N: height_case_in = 79.8125 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

79.8125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 82594863.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RS36A80J1N: height_hinge_in = 79.8125 in

Why this value was used

Reviewed manufacturer dimensions for RS36A80J1N: height_hinge_in = 79.8125 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

23.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 82594863.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RS36A80J1N: depth_case_only_in = 23.75 in

Why this value was used

Reviewed manufacturer dimensions for RS36A80J1N: depth_case_only_in = 23.75 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.5 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 23 3/4 + 3/4 = 24 1/2 in (RD3680 panel configuration)

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — RS36A80J1N_82594863.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Chassis depth without panels 23 3/4 in; page-14 footnote specifies an additional 3/4 in for RD3680/R
Reviewed: 2026-09-10

Chassis depth without panels 23 3/4 in; page-14 footnote specifies an additional 3/4 in for RD3680/RD3684 panel sets; installed depth = 24 1/2 in.

Why this value was used

Chassis depth without panels 23 3/4 in; page-14 footnote specifies an additional 3/4 in for RD3680/RD3684 panel sets; installed depth = 24 1/2 in. Calculation or inference: 23 3/4 + 3/4 = 24 1/2 in (RD3680 panel configuration).

Other evidence found

• 23.75 in — superseded

  Document 82594860.pdf (p.5); page 5. Model scope: not separately recorded. Raw value: G Overall depth of product (excl. front door panels) -> 23 3/4". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

26.125 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 23 3/4 + 3/4 + 1 5/8 = 26 1/8 in (RD3680 and square-fine handle)

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — RS36A80J1N_82594863.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installed depth 24 1/2 in plus RS36 square-fine handle projection 1 5/8 in = 26 1/8 in.
Reviewed: 2026-09-10

Installed depth 24 1/2 in plus RS36 square-fine handle projection 1 5/8 in = 26 1/8 in.

Why this value was used

Installed depth 24 1/2 in plus RS36 square-fine handle projection 1 5/8 in = 26 1/8 in. Calculation or inference: 23 3/4 + 3/4 + 1 5/8 = 26 1/8 in (RD3680 and square-fine handle).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

43.375 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 23 3/4 + 3/4 + 18 7/8 = 43 3/8 in (90-degree RD3680 configuration)

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — RS36A80J1N_82594863.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Chassis 23 3/4 in + RD3680 panel allowance 3/4 in + door depth from front of door 18 7/8 in = 43 3/8
Reviewed: 2026-09-10

Chassis 23 3/4 in + RD3680 panel allowance 3/4 in + door depth from front of door 18 7/8 in = 43 3/8 in; page 14 visually depicts the 90-degree condition.

Why this value was used

Chassis 23 3/4 in + RD3680 panel allowance 3/4 in + door depth from front of door 18 7/8 in = 43 3/8 in; page 14 visually depicts the 90-degree condition. Calculation or inference: 23 3/4 + 3/4 + 18 7/8 = 43 3/8 in (90-degree RD3680 configuration).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 82594863.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RS36A80J1N: min_cutout_width_in = 36 in

Why this value was used

Reviewed manufacturer dimensions for RS36A80J1N: min_cutout_width_in = 36 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

80 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: resolved fraction/unit/scenario semantics from cached full-page evidence

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 82594858.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

full-page adjudication=80.0; parser candidates=[80.0, 84.0]; height of cavity 80"

Why this value was used

full-page adjudication=80.0; parser candidates=[80.0, 84.0]; height of cavity 80"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: resolved fraction/unit/scenario semantics from cached full-page evidence

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 82594858.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

full-page adjudication=24.75; parser candidates=[36.0, 24.75]; cavity 36"

Why this value was used

full-page adjudication=24.75; parser candidates=[36.0, 24.75]; cavity 36"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.15625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 82594858.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

Exact family guide: minimum cabinetry gap from edge of product 5/32 in.

Why this value was used

Exact family guide: minimum cabinetry gap from edge of product 5/32 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.15625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 82594858.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

Exact family guide: minimum cabinetry gap from edge of product 5/32 in.

Why this value was used

Exact family guide: minimum cabinetry gap from edge of product 5/32 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.1875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 80 - 79 13/16 = 3/16 in

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — RS36A80J1N_82594863.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-10

RD3680 cavity height 80 in; overall appliance height 79 13/16 in; residual = 3/16 in.

Why this value was used

RD3680 cavity height 80 in; overall appliance height 79 13/16 in; residual = 3/16 in. Calculation or inference: 80 - 79 13/16 = 3/16 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 24 3/4 - 23 3/4 = 1 in (proud minimum-depth installation)

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — RS36A80J1N_82594863.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-10

Minimum proud-installation cavity depth 24 3/4 in; chassis depth without door panels 23 3/4 in; rear residual = 1 in.

Why this value was used

Minimum proud-installation cavity depth 24 3/4 in; chassis depth without door panels 23 3/4 in; rear residual = 1 in. Calculation or inference: 24 3/4 - 23 3/4 = 1 in (proud minimum-depth installation).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

4.3125 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 82594858.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-10-25

Exact-model installation guide, Door Opening & Clearance Dimensions: "Minimum door clearance to adjacent wall (90° – reduced internal access) 4 5/16"", measured from the front cabinetry edge. (115° full access: 12 3/8".)

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Exact-model installation guide, Door Opening & Clearance Dimensions: "Minimum door clearance to adjacent wall (90° – reduced internal access) 4 5/16"", measured from the front cabinetry edge. (115° full access: 12 3/8".)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

12.375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — RS36A80J1N_82594863.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 14
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in (fully open). Minimum door clearance to adjacent wall at 115 degrees (full internal access) 12 3/8 in.

Why this value was used

Migrated from hinge_side_wall_clearance_in (fully open). Minimum door clearance to adjacent wall at 115 degrees (full internal access) 12 3/8 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.6875 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 82594863.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RS36A80J1N: case_width_in = 35.6875 in

Why this value was used

Reviewed manufacturer dimensions for RS36A80J1N: case_width_in = 35.6875 in

Other evidence found

• 35.0625 in — superseded

  Document 82594859.pdf; page 1. Model scope: not separately recorded. Raw value: Width 35 1/16". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.