Measurement evidence for Fisher and Paykel RS36A72J1N

Value used by ExactFit

35.6875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 74493562.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-10-04

Width of bottom drawer panel 35 11/16", the widest front panel. Integrated column: measured across the installed panels (owner decision 2026-09-24).

Why this value was used

Width of bottom drawer panel 35 11/16", the widest front panel. Integrated column: measured across the installed panels (owner decision 2026-09-24).

Other evidence found

• 35.0625 in — superseded

  Document 82594868.pdf; page 1. Model scope: not separately recorded. Raw value: Width 35 1/16". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

71.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 74493556.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RS36A72J1N: height_case_in = 71.875 in

Why this value was used

Reviewed manufacturer dimensions for RS36A72J1N: height_case_in = 71.875 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

71.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 74493556.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RS36A72J1N: height_hinge_in = 71.875 in

Why this value was used

Reviewed manufacturer dimensions for RS36A72J1N: height_hinge_in = 71.875 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

23.6875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 74493556.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RS36A72J1N: depth_case_only_in = 23.6875 in

Why this value was used

Reviewed manufacturer dimensions for RS36A72J1N: depth_case_only_in = 23.6875 in

Other evidence found

• 23.75 in — superseded

  Document 78237245.pdf (p.3); page 3. Model scope: not separately recorded. Raw value: G Overall depth of product (excl. front door panels) -> 23 3/4". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.4375 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 23 11/16 + 3/4 = 24 7/16 in (standard panel configuration)

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 11
Reviewed: 2026-09-10

Chassis depth 23 11/16 in plus recorded standard panel depth 3/4 in = 24 7/16 in.

Why this value was used

Chassis depth 23 11/16 in plus recorded standard panel depth 3/4 in = 24 7/16 in. Calculation or inference: 23 11/16 + 3/4 = 24 7/16 in (standard panel configuration).

Other evidence found

• 23.75 in — superseded

  Document 78237245.pdf (p.3); page 3. Model scope: not separately recorded. Raw value: G Overall depth of product (excl. front door panels) -> 23 3/4". The final reviewed registry supersedes this earlier audit value.

• 24.5 in — superseded

  Document 74493556.pdf; page 9. Model scope: not separately recorded. Raw value: Reviewed manufacturer dimensions for RS36A72J1N: depth_less_handles_in = 24.5 in. The final reviewed registry supersedes this earlier audit value.

• 24.5 in — superseded

  Document 74493556.pdf; page 9. Model scope: not separately recorded. Raw value: Reviewed manufacturer dimensions for RS36A72J1N: depth_less_handles_in = 24.5 in. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

26.0625 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 23 11/16 + 3/4 + 1 5/8 = 26 1/16 in (standard panel and square-fine handle)

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Installed depth excluding handle 24 7/16 in plus visually labeled square-fine handle front projectio
Reviewed: 2026-09-10

Installed depth excluding handle 24 7/16 in plus visually labeled square-fine handle front projection 1 5/8 in = 26 1/16 in.

Why this value was used

Installed depth excluding handle 24 7/16 in plus visually labeled square-fine handle front projection 1 5/8 in = 26 1/16 in. Calculation or inference: 23 11/16 + 3/4 + 1 5/8 = 26 1/16 in (standard panel and square-fine handle).

Other evidence found

• 26.125 in — superseded

  Document 74493556.pdf; page 9. Model scope: not separately recorded. Raw value: Reviewed manufacturer dimensions for RS36A72J1N: depth_with_handles_in = 26.125 in. The final reviewed registry supersedes this earlier audit value.

• 26.125 in — superseded

  Document 74493556.pdf; page 9. Model scope: not separately recorded. Raw value: Reviewed manufacturer dimensions for RS36A72J1N: depth_with_handles_in = 26.125 in. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

41.9375 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 23 11/16 + 3/4 + 17.5 = 41.9375 in (90-degree, standard panel configuration)

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Chassis 23 11/16 in plus standard panel 3/4 in plus family door-swing depth at 90 degrees 17.5 in =
Reviewed: 2026-09-10

Chassis 23 11/16 in plus standard panel 3/4 in plus family door-swing depth at 90 degrees 17.5 in = 41.9375 in.

Why this value was used

Chassis 23 11/16 in plus standard panel 3/4 in plus family door-swing depth at 90 degrees 17.5 in = 41.9375 in. Calculation or inference: 23 11/16 + 3/4 + 17.5 = 41.9375 in (90-degree, standard panel configuration).

Other evidence found

• 42 in — superseded

  Document 74493556.pdf; page 16. Model scope: not separately recorded. Raw value: Reviewed manufacturer dimensions for RS36A72J1N: depth_doors_open_90_in = 42 in. The final reviewed registry supersedes this earlier audit value.

• 42 in — superseded

  Document 74493556.pdf; page 16. Model scope: not separately recorded. Raw value: Reviewed manufacturer dimensions for RS36A72J1N: depth_doors_open_90_in = 42 in. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 74493562.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-10-04

Cavity dimensions: G Overall width of cavity 36". The model installation guide replaces the generic French-door guide.

Why this value was used

Cavity dimensions: G Overall width of cavity 36". The model installation guide replaces the generic French-door guide.

Other evidence found

• 0.1575 in — superseded

  Document 78237245.pdf (p.3); page 3. Model scope: not separately recorded. Raw value: Overall width of cavity -> when adjoining cabinetry cannot share 4mm door gap. The final reviewed registry supersedes this earlier audit value.

• 35.1875 in — superseded

  dam.fisherpaykel.com; page 11. Model scope: not separately recorded. Raw value: Minimum clearances: overall width of cavity 35 3/16 to 35 11/32 in; minimum endpoint 35 3/16 in.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

72 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 11
Reviewed: 2026-09-10

Minimum clearances: cavity overall height 72 in.

Why this value was used

Minimum clearances: cavity overall height 72 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf
Fisher and Paykel · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 11
Reviewed: 2026-09-10

Minimum clearances: minimum overall depth of cavity 25 in.

Why this value was used

Minimum clearances: minimum overall depth of cavity 25 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.15625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 82594867.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

Exact family guide: minimum cabinetry gap from edge of custom panels 5/32 in.

Why this value was used

Exact family guide: minimum cabinetry gap from edge of custom panels 5/32 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.15625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 82594867.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

Exact family guide: minimum cabinetry gap from edge of custom panels 5/32 in.

Why this value was used

Exact family guide: minimum cabinetry gap from edge of custom panels 5/32 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 72 - 71 7/8 = 1/8 in

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 11
Reviewed: 2026-09-10

Cavity height 72 in and overall product height 71 7/8 in; residual = 1/8 in.

Why this value was used

Cavity height 72 in and overall product height 71 7/8 in; residual = 1/8 in. Calculation or inference: 72 - 71 7/8 = 1/8 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1.3125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 25 - 23 11/16 = 1 5/16 in

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 11
Reviewed: 2026-09-10

Minimum cavity depth 25 in and chassis depth 23 11/16 in from the front-of-chassis datum; residual = 1 5/16 in.

Why this value was used

Minimum cavity depth 25 in and chassis depth 23 11/16 in from the front-of-chassis datum; residual = 1 5/16 in. Calculation or inference: 25 - 23 11/16 = 1 5/16 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.8125 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 82594867.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in (90 degrees). Exact family guide: minimum door clearance to adjacent wall at 90 degrees 3 13/16 in.

Why this value was used

Migrated from hinge_side_wall_clearance_in (90 degrees). Exact family guide: minimum door clearance to adjacent wall at 90 degrees 3 13/16 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

11.8125 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 74493562.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 16
Reviewed: 2026-10-04

D Minimum door clearance to adjacent wall (115 degrees, full internal access): 11 13/16" (300 mm).

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

D Minimum door clearance to adjacent wall (115 degrees, full internal access): 11 13/16" (300 mm).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.0625 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 74493556.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RS36A72J1N: case_width_in = 35.0625 in

Why this value was used

Reviewed manufacturer dimensions for RS36A72J1N: case_width_in = 35.0625 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.