This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-26. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.75 in | ✓ Conflicting sources — resolved | Fisher and Paykel installation document — 105850787.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit35.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 105850787.pdf Reviewed manufacturer dimensions for RS3684AUVE1: width_doors_closed_in = 35.75 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS3684AUVE1: width_doors_closed_in = 35.75 in Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 84 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 105850787.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 105850787.pdf Reviewed manufacturer dimensions for RS3684AUVE1: height_case_in = 84 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS3684AUVE1: height_case_in = 84 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 84 in | ✓ Conflicting sources — resolved | Fisher and Paykel installation document — 105850787.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 105850787.pdf Reviewed manufacturer dimensions for RS3684AUVE1: height_hinge_in = 84 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS3684AUVE1: height_hinge_in = 84 in Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 105850787.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 105850787.pdf Reviewed manufacturer dimensions for RS3684AUVE1: depth_case_only_in = 24 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS3684AUVE1: depth_case_only_in = 24 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 24.75 in | ✓ Verified — retained secondary source · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf assets.skulytics.io | Page 22 | |
Value used by ExactFit24.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24 + 3/4 = 24 3/4 in Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf Chassis depth excluding door panel 24 in; assumed door-panel depth 3/4 in; installed depth excluding handle = 24 3/4 in.Open original source ↗ All retained supporting links
Why this value was usedChassis depth excluding door panel 24 in; assumed door-panel depth 3/4 in; installed depth excluding handle = 24 3/4 in. Calculation or inference: 24 + 3/4 = 24 3/4 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 26.375 in | ✓ Conflicting sources — resolved · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf assets.skulytics.io | Retained specification excerpt: Visually verified model-family page: chassis depth 24 in and assumed panel 3/4 in. Page 11: standard | |
Value used by ExactFit26.375 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24 + 3/4 + 1 5/8 = 26 3/8 in (standard handle configuration) Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf Visually verified model-family page: chassis depth 24 in and assumed panel 3/4 in. Page 11: standard Contemporary/Minimal/Classic handle profile 1 5/8 in (Professional Round is a separate 2 1/4 in option). Standard-handle installed depth = 26 3/8 in.Open original source ↗ All retained supporting links
Why this value was usedVisually verified model-family page: chassis depth 24 in and assumed panel 3/4 in. Page 11: standard Contemporary/Minimal/Classic handle profile 1 5/8 in (Professional Round is a separate 2 1/4 in option). Standard-handle installed depth = 26 3/8 in. Calculation or inference: 24 + 3/4 + 1 5/8 = 26 3/8 in (standard handle configuration). Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 47.375 in | ✓ Conflicting sources — resolved · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf assets.skulytics.io | Page 22 | |
Value used by ExactFit47.375 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24 + 3/4 + 22 5/8 = 47 3/8 in Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf Chassis 24 in + assumed 3/4 in panel + door depth from front of panel at 90 degrees 22 5/8 in = 47 3/8 in.Open original source ↗ All retained supporting links
Why this value was usedChassis 24 in + assumed 3/4 in panel + door depth from front of panel at 90 degrees 22 5/8 in = 47 3/8 in. Calculation or inference: 24 + 3/4 + 22 5/8 = 47 3/8 in. Other evidence found
Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Conflicting sources — resolved | Fisher and Paykel installation document — 105850787.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 105850787.pdf Reviewed manufacturer dimensions for RS3684AUVE1: min_cutout_width_in = 36 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS3684AUVE1: min_cutout_width_in = 36 in Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 84 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — 105850787.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 105850787.pdf Exact planning guide: cavity height 84 in.Open original source ↗ Why this value was usedExact planning guide: cavity height 84 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — 105850787.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 105850787.pdf Exact planning guide: cavity depth 25 in with services outside cavity.Open original source ↗ Why this value was usedExact planning guide: cavity depth 25 in with services outside cavity. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — 105850787.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 105850787.pdf Exact planning guide: minimum cabinetry gap from edge of door panels 1/8 in.Open original source ↗ Why this value was usedExact planning guide: minimum cabinetry gap from edge of door panels 1/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — 105850787.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 105850787.pdf Exact planning guide: minimum cabinetry gap from edge of door panels 1/8 in.Open original source ↗ Why this value was usedExact planning guide: minimum cabinetry gap from edge of door panels 1/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0 in | ✓ Verified — retained secondary source · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf assets.skulytics.io | Page 22 | |
Value used by ExactFit0 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 84 - 84 = 0 in Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf Product height 84 in and cavity height 84 in; residual = 0 in.Open original source ↗ All retained supporting links
Why this value was usedProduct height 84 in and cavity height 84 in; residual = 0 in. Calculation or inference: 84 - 84 = 0 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.25 in | ✓ Verified — retained secondary source · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf assets.skulytics.io | Page 22 | |
Value used by ExactFit0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 25 - 24 - 3/4 = 1/4 in Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf Minimum shallow cavity depth 25 in, chassis depth excluding panel 24 in, standard panel 3/4 in; installed residual = 1/4 in.Open original source ↗ All retained supporting links
Why this value was usedMinimum shallow cavity depth 25 in, chassis depth excluding panel 24 in, standard panel 3/4 in; installed residual = 1/4 in. Calculation or inference: 25 - 24 - 3/4 = 1/4 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 4.3125 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — 105850787.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit4.3125 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidenceFisher and Paykel measurement source — 105850787.pdf Migrated from hinge_side_wall_clearance_in (90 degrees). Exact planning guide: minimum door clearance to adjacent wall at 90 degrees 4 5/16 in.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in (90 degrees). Exact planning guide: minimum door clearance to adjacent wall at 90 degrees 4 5/16 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | 12.25 in | ? Verified — finalized database measurement | Fisher and Paykel measurement source — a9a38ef4c3e24d1a614da024378204c59e88cab841dbee76843aa5ac7892d75c.pdf Publisher not recorded | Page 25 | |
Value used by ExactFit12.25 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — a9a38ef4c3e24d1a614da024378204c59e88cab841dbee76843aa5ac7892d75c.pdf Door at 115 degrees with full internal access: 12 1/4 in. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedDoor at 115 degrees with full internal access: 12 1/4 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.75 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 105850787.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit35.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 105850787.pdf Reviewed manufacturer dimensions for RS3684AUVE1: case_width_in = 35.75 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS3684AUVE1: case_width_in = 35.75 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 35.75 in. Earlier retained values: 24 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Reviewed manufacturer dimensions for RS3684AUVE1: width_doors_closed_in = 35.75 in
View source scope, location, and impact on fitSelected: 84 in. Earlier retained values: 24 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Reviewed manufacturer dimensions for RS3684AUVE1: height_hinge_in = 84 in
View source scope, location, and impact on fitSelected: 26.375 in. Earlier retained values: 24 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Visually verified model-family page: chassis depth 24 in and assumed panel 3/4 in. Page 11: standard Contemporary/Minimal/Classic handle profile 1 5/8 in (Professional Round is a separate 2 1/4 in option). Standard-handle installed depth = 26 3/8 in. Calculation or inference: 24 + 3/4 + 1 5/8 = 26 3/8 in (standard handle configuration).
View source scope, location, and impact on fitSelected: 47.375 in. Earlier retained values: 46.625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Chassis 24 in + assumed 3/4 in panel + door depth from front of panel at 90 degrees 22 5/8 in = 47 3/8 in. Calculation or inference: 24 + 3/4 + 22 5/8 = 47 3/8 in.
View source scope, location, and impact on fitSelected: 36 in. Earlier retained values: 24 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Reviewed manufacturer dimensions for RS3684AUVE1: min_cutout_width_in = 36 in
View source scope, location, and impact on fitassets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: RS3684AUVE1. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
11 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: RS3684AUVE1. Publication/revision date: Not recorded. Reviewed: 2026-09-10.
5 displayed measurements supported: Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-09-26.
1 displayed measurements supported: Wall clearance for fully open door.
Availability: retained review record; original URL unavailable in the record.
Evidence reflects the sources reviewed on 2026-09-26. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.