This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-04. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 31.6875 in | ✓ Conflicting sources — resolved | Fisher and Paykel measurement source — 74493562.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit31.6875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 74493562.pdf Width of bottom drawer panel 31 11/16", the widest front panel. Integrated column: measured across the installed panels (owner decision 2026-09-24).Open original source ↗ Why this value was usedWidth of bottom drawer panel 31 11/16", the widest front panel. Integrated column: measured across the installed panels (owner decision 2026-09-24). Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 71.875 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 74493556.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit71.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 74493556.pdf Reviewed manufacturer dimensions for RS32A72J1: height_case_in = 71.875 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS32A72J1: height_case_in = 71.875 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 71.875 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 74493556.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit71.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 74493556.pdf Reviewed manufacturer dimensions for RS32A72J1: height_hinge_in = 71.875 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS32A72J1: height_hinge_in = 71.875 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 23.6875 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 74493556.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit23.6875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 74493556.pdf Reviewed manufacturer dimensions for RS32A72J1: depth_case_only_in = 23.6875 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS32A72J1: depth_case_only_in = 23.6875 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 24.4375 in | ✓ Conflicting sources — resolved · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf assets.skulytics.io | Page 13 | |
Value used by ExactFit24.4375 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 23 11/16 + 3/4 = 24 7/16 in (standard panel configuration) Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf Chassis depth 23 11/16 in plus recorded standard panel depth 3/4 in = 24 7/16 in.Open original source ↗ All retained supporting links
Why this value was usedChassis depth 23 11/16 in plus recorded standard panel depth 3/4 in = 24 7/16 in. Calculation or inference: 23 11/16 + 3/4 = 24 7/16 in (standard panel configuration). Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 26.0625 in | ✓ Conflicting sources — resolved · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf assets.skulytics.io | Retained specification excerpt: Installed depth excluding handle 24 7/16 in plus visually labeled square-fine handle front projectio | |
Value used by ExactFit26.0625 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 23 11/16 + 3/4 + 1 5/8 = 26 1/16 in (standard panel and square-fine handle) Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf Installed depth excluding handle 24 7/16 in plus visually labeled square-fine handle front projection 1 5/8 in = 26 1/16 in.Open original source ↗ All retained supporting links
Why this value was usedInstalled depth excluding handle 24 7/16 in plus visually labeled square-fine handle front projection 1 5/8 in = 26 1/16 in. Calculation or inference: 23 11/16 + 3/4 + 1 5/8 = 26 1/16 in (standard panel and square-fine handle). Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 40 in | ✓ Conflicting sources — resolved · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf assets.skulytics.io | Retained specification excerpt: Chassis 23 11/16 in plus standard panel 3/4 in plus family door-swing depth at 90 degrees 15.5625 in | |
Value used by ExactFit40 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 23 11/16 + 3/4 + 15.5625 = 40.0 in (90-degree, standard panel configuration) Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf Chassis 23 11/16 in plus standard panel 3/4 in plus family door-swing depth at 90 degrees 15.5625 in = 40.0 in.Open original source ↗ All retained supporting links
Why this value was usedChassis 23 11/16 in plus standard panel 3/4 in plus family door-swing depth at 90 degrees 15.5625 in = 40.0 in. Calculation or inference: 23 11/16 + 3/4 + 15.5625 = 40.0 in (90-degree, standard panel configuration). Other evidence found
Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 32 in | ✓ Conflicting sources — resolved | Fisher and Paykel measurement source — 74493562.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit32 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 74493562.pdf Cavity dimensions: G Overall width of cavity 32". The model installation guide replaces the generic French-door guide.Open original source ↗ All retained supporting links
Why this value was usedCavity dimensions: G Overall width of cavity 32". The model installation guide replaces the generic French-door guide. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 72 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — 74493556.pdf assets.skulytics.io | Page 16 | |
Value used by ExactFit72 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 74493556.pdf Exact RS32A72 family guide: overall cavity height 72 in.Open original source ↗ Why this value was usedExact RS32A72 family guide: overall cavity height 72 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Conflicting sources — resolved | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf assets.skulytics.io | Page 13 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf Minimum clearances: minimum overall depth of cavity 25 in.Open original source ↗ All retained supporting links
Why this value was usedMinimum clearances: minimum overall depth of cavity 25 in. Other evidence found
Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.15625 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — 74493556.pdf assets.skulytics.io | Page 16 | |
Value used by ExactFit0.15625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 74493556.pdf Exact family guide: minimum cabinetry gap from edge of custom panels 5/32 in.Open original source ↗ Why this value was usedExact family guide: minimum cabinetry gap from edge of custom panels 5/32 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.15625 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — 74493556.pdf assets.skulytics.io | Page 16 | |
Value used by ExactFit0.15625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 74493556.pdf Exact family guide: minimum cabinetry gap from edge of custom panels 5/32 in.Open original source ↗ Why this value was usedExact family guide: minimum cabinetry gap from edge of custom panels 5/32 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.125 in | ✓ Verified — retained secondary source · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf assets.skulytics.io | Page 13 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 72 - 71 7/8 = 1/8 in Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf Cavity overall height 72 in; overall product height 71 7/8 in; residual = 1/8 in.Open original source ↗ All retained supporting links
Why this value was usedCavity overall height 72 in; overall product height 71 7/8 in; residual = 1/8 in. Calculation or inference: 72 - 71 7/8 = 1/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1.3125 in | ✓ Conflicting sources — resolved · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf assets.skulytics.io | Page 13 | |
Value used by ExactFit1.3125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 25 - 23 11/16 = 1 5/16 in Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS32A72J1-RS32A72U1-RS36A72J1-RS36A72U1-IntegratedFrenchDoorRefrigeratorFreezer-0-90004833B-US-CA.pdf Minimum cavity depth 25 in and chassis depth 23 11/16 in from the visible front-of-chassis datum; rear residual = 1 5/16 in.Open original source ↗ All retained supporting links
Why this value was usedMinimum cavity depth 25 in and chassis depth 23 11/16 in from the visible front-of-chassis datum; rear residual = 1 5/16 in. Calculation or inference: 25 - 23 11/16 = 1 5/16 in. Other evidence found
Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 3.9375 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — 74493556.pdf assets.skulytics.io | Page 16 | |
Value used by ExactFit3.9375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidenceFisher and Paykel measurement source — 74493556.pdf Migrated from hinge_side_wall_clearance_in (90 degrees). Exact family guide: minimum door clearance to adjacent wall at 90 degrees 3 15/16 in.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in (90 degrees). Exact family guide: minimum door clearance to adjacent wall at 90 degrees 3 15/16 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | 11 in | ? Verified — finalized database measurement | Fisher and Paykel measurement source — 74493562.pdf Publisher not recorded | Page 16 | |
Value used by ExactFit11 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 74493562.pdf D Minimum door clearance to adjacent wall (115 degrees, full internal access): 11" (280 mm). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedD Minimum door clearance to adjacent wall (115 degrees, full internal access): 11" (280 mm). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 31.125 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 74493556.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit31.125 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 74493556.pdf Reviewed manufacturer dimensions for RS32A72J1: case_width_in = 31.125 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS32A72J1: case_width_in = 31.125 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 31.6875 in. Earlier retained values: 31.125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Width of bottom drawer panel 31 11/16", the widest front panel. Integrated column: measured across the installed panels (owner decision 2026-09-24).
View source scope, location, and impact on fitSelected: 24.4375 in. Earlier retained values: 24.5 in, 24.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Chassis depth 23 11/16 in plus recorded standard panel depth 3/4 in = 24 7/16 in. Calculation or inference: 23 11/16 + 3/4 = 24 7/16 in (standard panel configuration).
View source scope, location, and impact on fitSelected: 26.0625 in. Earlier retained values: 23.6875 in, 26.125 in, 26.125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Installed depth excluding handle 24 7/16 in plus visually labeled square-fine handle front projection 1 5/8 in = 26 1/16 in. Calculation or inference: 23 11/16 + 3/4 + 1 5/8 = 26 1/16 in (standard panel and square-fine handle).
View source scope, location, and impact on fitSelected: 40 in. Earlier retained values: 40.0625 in, 40.0625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Chassis 23 11/16 in plus standard panel 3/4 in plus family door-swing depth at 90 degrees 15.5625 in = 40.0 in. Calculation or inference: 23 11/16 + 3/4 + 15.5625 = 40.0 in (90-degree, standard panel configuration).
View source scope, location, and impact on fitSelected: 32 in. Earlier retained values: 31.25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Cavity dimensions: G Overall width of cavity 32". The model installation guide replaces the generic French-door guide.
View source scope, location, and impact on fitSelected: 25 in. Earlier retained values: 24 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Minimum clearances: minimum overall depth of cavity 25 in.
View source scope, location, and impact on fitSelected: 1.3125 in. Earlier retained values: 0.3125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Minimum cavity depth 25 in and chassis depth 23 11/16 in from the visible front-of-chassis datum; rear residual = 1 5/16 in. Calculation or inference: 25 - 23 11/16 = 1 5/16 in.
View source scope, location, and impact on fitPublisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-10-04.
3 displayed measurements supported: Overall width; Minimum cutout width; Wall clearance for fully open door.
Availability: retained review record; original URL unavailable in the record.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: RS32A72J1. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
8 displayed measurements supported: Cabinet height; Height with hinge / controlling height; Depth without door; Minimum cutout height; Left-side ventilation clearance; Right-side ventilation clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: RS32A72J1. Publication/revision date: Not recorded. Reviewed: 2026-09-10.
6 displayed measurements supported: Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout depth; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-04. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.