Measurement evidence for Fisher and Paykel RS3084SRK1

Value used by ExactFit

Unknown · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher Paykel RS1884FLJE1 Planning Guide Integrated Refrigeration
assets.skulytics.io · Planning Guide Integrated Refrigeration
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RS3084SRK1: width_doors_closed_in = 29.75 in

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 29.75 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher Paykel RS1884FLJE1 Planning Guide Integrated Refrigeration
assets.skulytics.io · Planning Guide Integrated Refrigeration
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RS3084SRK1: height_case_in = 84 in

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 84 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher Paykel RS1884FLJE1 Planning Guide Integrated Refrigeration
assets.skulytics.io · Planning Guide Integrated Refrigeration
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RS3084SRK1: height_hinge_in = 84 in

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 84 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher Paykel RS1884FLJE1 Planning Guide Integrated Refrigeration
assets.skulytics.io · Planning Guide Integrated Refrigeration
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RS3084SRK1: depth_case_only_in = 24 in

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 24 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + 0.75 in standard panel

Confidence label: medium.

Calculation inputs: Depth without door;

Primary evidence

Fisher Paykel RS1884FLJE1 Planning Guide Integrated Refrigeration
assets.skulytics.io · Planning Guide Integrated Refrigeration
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-04

24 in chassis plus the planning guide's standard 3/4 in door panel.

Why this value was used

A required calculation input lacks defensible evidence.

Retained research value: 24.75 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

• 24 in — superseded

  74613261.pdf (p.1); page 1. Model scope: not separately recorded. Raw value: G Overall depth of product (excl. door front panel) -> 24". The final reviewed registry supersedes this earlier audit value. 24 in chassis plus the planning guide's standard 3/4 in door panel.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + 0.75 in panel + 1.625 in handle

Confidence label: medium.

Calculation inputs: Depth without door;

Primary evidence

Fisher Paykel RS1884FLJE1 Planning Guide Integrated Refrigeration
assets.skulytics.io · Planning Guide Integrated Refrigeration
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-04

Planning-guide installed configuration: 24 in chassis + 3/4 in panel + 1 5/8 in handle.

Why this value was used

A required calculation input lacks defensible evidence.

Retained research value: 26.375 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

• 24 in — superseded

  https://www.fisherpaykel.com/us/cooling/integrated/30in-series-9-integrated-column-refrigerator--rs3084srk1-26897.html; location not retained. Model scope: not separately recorded. Raw value: Plain exact-model specification row: Depth = 24.0 in | ply voltage | 115V | ### Product dimensions | Product dimensions Attributes | Value | | --- | --- | | Depth | 24" | | Height | 84" | | Width | 29 3⁄4" | ### Product information | Product information Attributes | Value | | --- | --- |. The final reviewed registry supersedes this earlier audit value. Planning-guide installed configuration: 24 in chassis + 3/4 in panel + 1 5/8 in handle.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_less_handles_in + 32 in open-door projection

Confidence label: medium.

Calculation inputs: Depth with door, without handles;

Primary evidence

Fisher Paykel RS1884FLJE1 Planning Guide Integrated Refrigeration
assets.skulytics.io · Planning Guide Integrated Refrigeration
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-04

Installed closed depth 24 3/4 in plus 32 in 90-degree open-door projection.

Why this value was used

A required calculation input lacks defensible evidence.

Retained research value: 56.75 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher Paykel RS1884FLJE1 Planning Guide Integrated Refrigeration
assets.skulytics.io · Planning Guide Integrated Refrigeration
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RS3084SRK1: min_cutout_width_in = 30 in

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 30 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

84 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from RS3084FLJE1

Confidence label: medium.

Primary evidence

Fisher Paykel RS3084FLJE1 Planning Guide Integrated Refrigeration
assets.skulytics.io · Planning Guide Integrated Refrigeration
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 6
Reviewed: 2026-09-05

Conflict-free identical-chassis propagation from Fisher_Paykel RS3084FLJE1: min_cutout_height_in=84.0 in.

Why this value was used

Conflict-free identical-chassis propagation from Fisher_Paykel RS3084FLJE1: min_cutout_height_in=84.0 in. Calculation or inference: identical 8-dimension chassis signature; propagated from RS3084FLJE1.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

specification guide integrated column refrigerators or freezers
static.pcrichard.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: depth of cavity* 25"
Reviewed: 2026-09-05

depth of cavity* 25"

Why this value was used

depth of cavity* 25"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher Paykel RS1884FLJE1 Planning Guide Integrated Refrigeration
assets.skulytics.io · Planning Guide Integrated Refrigeration
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-05

Exact family table: minimum cabinetry gap from edge of door panel 1/8 in.

Why this value was used

Exact family table: minimum cabinetry gap from edge of door panel 1/8 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher Paykel RS1884FLJE1 Planning Guide Integrated Refrigeration
assets.skulytics.io · Planning Guide Integrated Refrigeration
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-05

Exact family table: minimum cabinetry gap from edge of door panel 1/8 in.

Why this value was used

Exact family table: minimum cabinetry gap from edge of door panel 1/8 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_height_in - height_case_in

Confidence label: medium.

Calculation inputs: Cabinet height; Minimum cutout height;

Primary evidence

Fisher Paykel RS1884FLJE1 Planning Guide Integrated Refrigeration
assets.skulytics.io · Planning Guide Integrated Refrigeration
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-05

Exact family table: product height and cavity overall height are both 84 in.

Why this value was used

A required calculation input lacks defensible evidence.

Retained research value: 0 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in - 0.75 in panel

Confidence label: medium.

Calculation inputs: Depth without door; Minimum cutout depth;

Primary evidence

Fisher Paykel RS1884FLJE1 Planning Guide Integrated Refrigeration
assets.skulytics.io · Planning Guide Integrated Refrigeration
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-05

Exact shallow-cavity table: 25 in cavity minus 24 in chassis minus assumed 3/4 in door panel = 1/4 in rear residual.

Why this value was used

A required calculation input lacks defensible evidence.

Retained research value: 0.25 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

4.3125 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher Paykel RS1884FLJE1 Planning Guide Integrated Refrigeration
assets.skulytics.io · Planning Guide Integrated Refrigeration
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-05

Exact family table: minimum door clearance to adjacent wall at 90 degrees is 4 5/16 in; normalizes rounded 4.312.

Why this value was used

Exact family table: minimum door clearance to adjacent wall at 90 degrees is 4 5/16 in; normalizes rounded 4.312.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher Paykel RS1884FLJE1 Planning Guide Integrated Refrigeration
assets.skulytics.io · Planning Guide Integrated Refrigeration
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RS3084SRK1: case_width_in = 29.75 in

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 29.75 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher Paykel RS1884FLJE1 Planning Guide Integrated Refrigeration
assets.skulytics.io · Planning Guide Integrated Refrigeration
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-04

Minimum door clearance to adjacent wall at 90 degrees: 4 5/16 in.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 4.3125 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

• 16.5 in — superseded

  74613259.pdf; page 1. Model scope: not separately recorded. Raw value: Minimum door clearance to adjacent wall (115° – full internal access) = 16 1/2".. The final reviewed registry supersedes this earlier audit value. Minimum door clearance to adjacent wall at 90 degrees: 4 5/16 in.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.