This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Column Refrigerator · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-15. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 29.75 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io | Page 20 | |
Value used by ExactFit29.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90272075.pdf Reviewed manufacturer dimensions for RS3084SRHK1: width_doors_closed_in = 29.75 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS3084SRHK1: width_doors_closed_in = 29.75 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 84 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io | Page 20 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90272075.pdf Reviewed manufacturer dimensions for RS3084SRHK1: height_case_in = 84 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS3084SRHK1: height_case_in = 84 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 84 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io | Page 20 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90272075.pdf Reviewed manufacturer dimensions for RS3084SRHK1: height_hinge_in = 84 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS3084SRHK1: height_hinge_in = 84 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io | Page 20 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90272075.pdf Reviewed manufacturer dimensions for RS3084SRHK1: depth_case_only_in = 24 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS3084SRHK1: depth_case_only_in = 24 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 24.75 in | ✓ Conflicting sources — resolved · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf assets.skulytics.io | Page 20 | |
Value used by ExactFit24.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24 + 3/4 = 24 3/4 in Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf 30-inch family chassis depth excluding panel 24 in plus assumed 3/4 in panel = 24 3/4 in.Open original source ↗ All retained supporting links
Why this value was used30-inch family chassis depth excluding panel 24 in plus assumed 3/4 in panel = 24 3/4 in. Calculation or inference: 24 + 3/4 = 24 3/4 in. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 26.375 in | ✓ Verified — retained secondary source · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf assets.skulytics.io | Retained specification excerpt: 30-inch chassis 24 in + 3/4 in panel + standard Contemporary/Minimal/Classic handle projection 1 5/8 | |
Value used by ExactFit26.375 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24 + 3/4 + 1 5/8 = 26 3/8 in (standard handle configuration) Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf 30-inch chassis 24 in + 3/4 in panel + standard Contemporary/Minimal/Classic handle projection 1 5/8 in = 26 3/8 in.Open original source ↗ All retained supporting links
Why this value was used30-inch chassis 24 in + 3/4 in panel + standard Contemporary/Minimal/Classic handle projection 1 5/8 in = 26 3/8 in. Calculation or inference: 24 + 3/4 + 1 5/8 = 26 3/8 in (standard handle configuration). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 56.75 in | ✓ Verified — retained secondary source · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf assets.skulytics.io | Page 20 | |
Value used by ExactFit56.75 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24 + 3/4 + 32 = 56 3/4 in Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf 30-inch chassis 24 in + 3/4 in panel + door projection from front of panel at 90 degrees 32 in = 56 3/4 in.Open original source ↗ All retained supporting links
Why this value was used30-inch chassis 24 in + 3/4 in panel + door projection from front of panel at 90 degrees 32 in = 56 3/4 in. Calculation or inference: 24 + 3/4 + 32 = 56 3/4 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 30 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io | Page 20 | |
Value used by ExactFit30 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90272075.pdf Reviewed manufacturer dimensions for RS3084SRHK1: min_cutout_width_in = 30 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS3084SRHK1: min_cutout_width_in = 30 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 84 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — FP-InstallGuide-en-RS1884-RS2484-RS3084-RS3684-IntegratedColumnRefrigerator-0-432136C-US-CA.pdf assets.skulytics.io | Page 8 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-InstallGuide-en-RS1884-RS2484-RS3084-RS3684-IntegratedColumnRefrigerator-0-432136C-US-CA.pdf RS3084SH family cover; 30-inch single-install cavity table: overall cavity height 84 in.Open original source ↗ All retained supporting links
Why this value was usedRS3084SH family cover; 30-inch single-install cavity table: overall cavity height 84 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Verified — exact model | Fisher and Paykel measurement source — FP-InstallGuide-en-RS1884-RS2484-RS3084-RS3684-IntegratedColumnRefrigerator-0-432136C-US-CA.pdf Fisher and Paykel | Page 8 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-InstallGuide-en-RS1884-RS2484-RS3084-RS3684-IntegratedColumnRefrigerator-0-432136C-US-CA.pdf 30-inch single-install cavity table: minimum cavity depth 25 in; assumes 3/4 in door panel.Open original source ↗ All retained supporting links
Why this value was used30-inch single-install cavity table: minimum cavity depth 25 in; assumes 3/4 in door panel. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io | Page 20 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 90272075.pdf Exact family table: minimum cabinetry gap from edge of door panel 1/8 in.Open original source ↗ Why this value was usedExact family table: minimum cabinetry gap from edge of door panel 1/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io | Page 20 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 90272075.pdf Exact family table: minimum cabinetry gap from edge of door panel 1/8 in.Open original source ↗ Why this value was usedExact family table: minimum cabinetry gap from edge of door panel 1/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0 in | ✓ Verified — retained secondary source · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf assets.skulytics.io | Retained specification excerpt: 30-inch product height 84 in and single-install cavity height 84 in; residual = 0 in. | |
Value used by ExactFit0 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 84 - 84 = 0 in Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf 30-inch product height 84 in and single-install cavity height 84 in; residual = 0 in.Open original source ↗ All retained supporting links
Why this value was used30-inch product height 84 in and single-install cavity height 84 in; residual = 0 in. Calculation or inference: 84 - 84 = 0 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.25 in | ✓ Verified — retained secondary source · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf assets.skulytics.io | Retained specification excerpt: Minimum cavity depth 25 in assumes 3/4 in panel; chassis depth 24 in; installed rear residual = 1/4 | |
Value used by ExactFit0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 25 - 24 - 3/4 = 1/4 in Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf Minimum cavity depth 25 in assumes 3/4 in panel; chassis depth 24 in; installed rear residual = 1/4 in.Open original source ↗ All retained supporting links
Why this value was usedMinimum cavity depth 25 in assumes 3/4 in panel; chassis depth 24 in; installed rear residual = 1/4 in. Calculation or inference: 25 - 24 - 3/4 = 1/4 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 4.3125 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io | Page 20 | |
Value used by ExactFit4.3125 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidenceFisher and Paykel measurement source — 90272075.pdf Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Exact family table: minimum door clearance to adjacent wall at 90 degrees is 4 5/16 in; normalizes rounded 4.312.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Exact family table: minimum door clearance to adjacent wall at 90 degrees is 4 5/16 in; normalizes rounded 4.312. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | 16.5 in | ? Conflicting sources — resolved | Fisher and Paykel measurement source — 74477815.pdf Publisher not recorded | Page 21 | |
Value used by ExactFit16.5 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 74477815.pdf Planning guide, 30" models: Minimum door clearance to adjacent wall (115° – full internal access) 16 1/2" (419 mm). Corrects an earlier fill that took the 18" (11 1/2") or 36" (17 1/8") column. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedPlanning guide, 30" models: Minimum door clearance to adjacent wall (115° – full internal access) 16 1/2" (419 mm). Corrects an earlier fill that took the 18" (11 1/2") or 36" (17 1/8") column. Other evidence found
Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 29.75 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io | Page 20 | |
Value used by ExactFit29.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90272075.pdf Reviewed manufacturer dimensions for RS3084SRHK1: case_width_in = 29.75 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS3084SRHK1: case_width_in = 29.75 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 24.75 in. Earlier retained values: 24 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
30-inch family chassis depth excluding panel 24 in plus assumed 3/4 in panel = 24 3/4 in. Calculation or inference: 24 + 3/4 = 24 3/4 in.
View source scope, location, and impact on fitSelected: 16.5 in. Earlier retained values: 17.125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Planning guide, 30" models: Minimum door clearance to adjacent wall (115° – full internal access) 16 1/2" (419 mm). Corrects an earlier fill that took the 18" (11 1/2") or 36" (17 1/8") column.
View source scope, location, and impact on fitassets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: RS3084SRHK1. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
9 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Minimum cutout width; Left-side ventilation clearance; Right-side ventilation clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: RS3084SRHK1. Publication/revision date: Not recorded. Reviewed: 2026-09-10.
5 displayed measurements supported: Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Fisher and Paykel · Web source · exact model/source
Model numbers covered: RS3084SRHK1. Publication/revision date: Not recorded. Reviewed: 2026-09-10.
2 displayed measurements supported: Minimum cutout height; Minimum cutout depth.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-10-15.
1 displayed measurements supported: Wall clearance for fully open door.
Availability: retained review record; original URL unavailable in the record.
Evidence reflects the sources reviewed on 2026-10-15. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.