Measurement evidence for Fisher and Paykel RS2484SRK1
This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-15. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Measurements and supporting evidence
Measurement
Value used
Evidence status
Primary source
Location
Details
Overall width
23.75 in
✓ Verified — retained secondary source
Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io
Page 17
Value used by ExactFit
23.75 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 17 Reviewed: 2026-09-04
Reviewed manufacturer dimensions for RS2484SRK1: width_doors_closed_in = 23.75 in
Reviewed manufacturer dimensions for RS2484SRK1: width_doors_closed_in = 23.75 in
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io
Page 17
Value used by ExactFit
84 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 17 Reviewed: 2026-09-04
Reviewed manufacturer dimensions for RS2484SRK1: height_case_in = 84 in
Reviewed manufacturer dimensions for RS2484SRK1: height_case_in = 84 in
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io
Page 17
Value used by ExactFit
84 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 17 Reviewed: 2026-09-04
Reviewed manufacturer dimensions for RS2484SRK1: height_hinge_in = 84 in
Reviewed manufacturer dimensions for RS2484SRK1: height_hinge_in = 84 in
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io
Page 17
Value used by ExactFit
24 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 17 Reviewed: 2026-09-04
Reviewed manufacturer dimensions for RS2484SRK1: depth_case_only_in = 24 in
Reviewed manufacturer dimensions for RS2484SRK1: depth_case_only_in = 24 in
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 17 Reviewed: 2026-09-09
Current manufacturer planning guide page 17 explicitly names RS2484SRK1 in the 24-inch refrigeration family. Overall chassis depth excluding panels is 24 in and the documented standard/custom panel assumption is 3/4 in.
Current manufacturer planning guide page 17 explicitly names RS2484SRK1 in the 24-inch refrigeration family. Overall chassis depth excluding panels is 24 in and the documented standard/custom panel assumption is 3/4 in. Calculation or inference: depth_case_only_in + 0.75 in standard panel.
Other evidence found
24 in — superseded
Document 74477877.pdf (p.1); page 1. Model scope: not separately recorded. Raw value: G Overall depth of product (excl. door front panel) -> 24". The final reviewed registry supersedes this earlier audit value.
Effect on fit result
This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Fisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf assets.skulytics.io
Retained specification excerpt: Visually verified model-family page: chassis depth 24 in and assumed panel 3/4 in. Page 11: standard
Value used by ExactFit
26.375 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: 24 + 3/4 + 1 5/8 = 26 3/8 in (standard handle configuration)
Confidence label: high.
Primary evidence
Fisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Visually verified model-family page: chassis depth 24 in and assumed panel 3/4 in. Page 11: standard Reviewed: 2026-09-10
Visually verified model-family page: chassis depth 24 in and assumed panel 3/4 in. Page 11: standard Contemporary/Minimal/Classic handle profile 1 5/8 in (Professional Round is a separate 2 1/4 in option). Standard-handle installed depth = 26 3/8 in.
Visually verified model-family page: chassis depth 24 in and assumed panel 3/4 in. Page 11: standard Contemporary/Minimal/Classic handle profile 1 5/8 in (Professional Round is a separate 2 1/4 in option). Standard-handle installed depth = 26 3/8 in. Calculation or inference: 24 + 3/4 + 1 5/8 = 26 3/8 in (standard handle configuration).
Other evidence found
24 in — superseded
www.fisherpaykel.com; location not retained. Model scope: not separately recorded. Raw value: Plain exact-model specification row: Depth = 24.0 in | ply voltage | 115V | ### Product dimensions | Product dimensions Attributes | Value | | --- | --- | | Depth | 24" | | Height | 84" | | Width | 23 3⁄4" | ### Product information | Product information Attributes | Value | | --- | --- |. The final reviewed registry supersedes this earlier audit value.
Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 17 Reviewed: 2026-09-09
Current manufacturer planning guide page 17 explicitly names RS2484SRK1 in the 24-inch refrigeration family. Depth of door at 90 degrees measured from front of door is 26 in; rear-to-front installed depth is 24 3/4 in, totaling 50.75 in.
Current manufacturer planning guide page 17 explicitly names RS2484SRK1 in the 24-inch refrigeration family. Depth of door at 90 degrees measured from front of door is 26 in; rear-to-front installed depth is 24 3/4 in, totaling 50.75 in. Calculation or inference: depth_less_handles_in + 26 in 90-degree door projection.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io
Page 17
Value used by ExactFit
24 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 17 Reviewed: 2026-09-04
Reviewed manufacturer dimensions for RS2484SRK1: min_cutout_width_in = 24 in
Reviewed manufacturer dimensions for RS2484SRK1: min_cutout_width_in = 24 in
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io
Page 17
Value used by ExactFit
84 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 17 Reviewed: 2026-09-09
Current manufacturer planning guide page 17 explicitly names RS2484SRK1 in the 24-inch refrigeration family. Clearance Dimensions directly print Cavity overall height 84 in.
Current manufacturer planning guide page 17 explicitly names RS2484SRK1 in the 24-inch refrigeration family. Clearance Dimensions directly print Cavity overall height 84 in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Fisher and Paykel measurement source — 90272075.pdf images.furnituredealer.net
Page 17
Value used by ExactFit
25 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Fisher and Paykel measurement source — 90272075.pdf images.furnituredealer.net · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 17 Reviewed: 2026-09-09
Current manufacturer planning guide page 17 explicitly names RS2484SRK1 in the 24-inch refrigeration family. Clearance Dimensions directly print minimum shallow cavity depth 25 in when services are outside the cavity.
Current manufacturer planning guide page 17 explicitly names RS2484SRK1 in the 24-inch refrigeration family. Clearance Dimensions directly print minimum shallow cavity depth 25 in when services are outside the cavity.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io
Page 17
Value used by ExactFit
0.125 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 17 Reviewed: 2026-09-05
Exact family table: minimum cabinetry gap from edge of door panel 1/8 in.
Exact family table: minimum cabinetry gap from edge of door panel 1/8 in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io
Page 17
Value used by ExactFit
0.125 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 17 Reviewed: 2026-09-05
Exact family table: minimum cabinetry gap from edge of door panel 1/8 in.
Exact family table: minimum cabinetry gap from edge of door panel 1/8 in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 17 Reviewed: 2026-09-09
Current manufacturer planning guide page 17 explicitly names RS2484SRK1 in the 24-inch refrigeration family. Product overall height and cavity overall height are both 84 in, giving a 0-in additive top residual.
Current manufacturer planning guide page 17 explicitly names RS2484SRK1 in the 24-inch refrigeration family. Product overall height and cavity overall height are both 84 in, giving a 0-in additive top residual. Calculation or inference: min_cutout_height_in - height_case_in (84 - 84).
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 17 Reviewed: 2026-09-09
Current manufacturer planning guide page 17 explicitly names RS2484SRK1 in the 24-inch refrigeration family. Standard installed depth is 24-in chassis plus 3/4-in panel; the shallow cavity is 25 in, leaving 1/4 in behind the installed front-plane assembly.
Current manufacturer planning guide page 17 explicitly names RS2484SRK1 in the 24-inch refrigeration family. Standard installed depth is 24-in chassis plus 3/4-in panel; the shallow cavity is 25 in, leaving 1/4 in behind the installed front-plane assembly. Calculation or inference: min_cutout_depth_in - depth_case_only_in - 0.75 in panel.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io
Page 17
Value used by ExactFit
4.3125 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization:
Confidence label: high.
Primary evidence
Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 17 Reviewed: 2026-09-17
Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Exact family table: minimum door clearance to adjacent wall at 90 degrees is 4 5/16 in; normalizes rounded 4.312.
Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Exact family table: minimum door clearance to adjacent wall at 90 degrees is 4 5/16 in; normalizes rounded 4.312.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Fisher and Paykel measurement source — 74477938.pdf Publisher not recorded
Page 5
Value used by ExactFit
14 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Fisher and Paykel measurement source — 74477938.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-10-15
14 in printed: D49f3e36945 p.5; condition: door fully open 115 degrees; custom panel and handle excluded on pages 9/22. Read by the verification agent from a document naming the model.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
14 in printed: D49f3e36945 p.5; condition: door fully open 115 degrees; custom panel and handle excluded on pages 9/22. Read by the verification agent from a document naming the model.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io
Page 17
Value used by ExactFit
23.75 in · Fit role: Informational only.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 17 Reviewed: 2026-09-04
Reviewed manufacturer dimensions for RS2484SRK1: case_width_in = 23.75 in
Selected: 24.75 in. Earlier retained values: 24 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Current manufacturer planning guide page 17 explicitly names RS2484SRK1 in the 24-inch refrigeration family. Overall chassis depth excluding panels is 24 in and the documented standard/custom panel assumption is 3/4 in. Calculation or inference: depth_case_only_in + 0.75 in standard panel.
Selected: 26.375 in. Earlier retained values: 24 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Visually verified model-family page: chassis depth 24 in and assumed panel 3/4 in. Page 11: standard Contemporary/Minimal/Classic handle profile 1 5/8 in (Professional Round is a separate 2 1/4 in option). Standard-handle installed depth = 26 3/8 in. Calculation or inference: 24 + 3/4 + 1 5/8 = 26 3/8 in (standard handle configuration).
Model numbers covered: RS2484SRK1. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
15 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-10-15. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
