This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Single Door Refrigerator · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-15. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 17.75 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io | Page 16 | |
Value used by ExactFit17.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90272075.pdf Reviewed manufacturer dimensions for RS1884FLJE1: width_doors_closed_in = 17.75 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS1884FLJE1: width_doors_closed_in = 17.75 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 84 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io | Page 16 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90272075.pdf Reviewed manufacturer dimensions for RS1884FLJE1: height_case_in = 84 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS1884FLJE1: height_case_in = 84 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 84 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io | Page 16 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90272075.pdf Reviewed manufacturer dimensions for RS1884FLJE1: height_hinge_in = 84 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS1884FLJE1: height_hinge_in = 84 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io | Page 16 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90272075.pdf Reviewed manufacturer dimensions for RS1884FLJE1: depth_case_only_in = 24 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS1884FLJE1: depth_case_only_in = 24 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 24.75 in | ✓ Verified — retained secondary source · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf assets.skulytics.io | Page 15 | |
Value used by ExactFit24.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24 + 0.75 Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf 24 in chassis depth plus the drawing's assumed 3/4 in panel.Open original source ↗ All retained supporting links
Why this value was used24 in chassis depth plus the drawing's assumed 3/4 in panel. Calculation or inference: 24 + 0.75. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 26.375 in | ✓ Verified — retained secondary source · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf assets.skulytics.io | Retained specification excerpt: Visually verified model-family page: chassis depth 24 in and assumed panel 3/4 in. Page 11: standard | |
Value used by ExactFit26.375 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24 + 3/4 + 1 5/8 = 26 3/8 in (standard handle configuration) Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf Visually verified model-family page: chassis depth 24 in and assumed panel 3/4 in. Page 11: standard Contemporary/Minimal/Classic handle profile 1 5/8 in (Professional Round is a separate 2 1/4 in option). Standard-handle installed depth = 26 3/8 in.Open original source ↗ All retained supporting links
Why this value was usedVisually verified model-family page: chassis depth 24 in and assumed panel 3/4 in. Page 11: standard Contemporary/Minimal/Classic handle profile 1 5/8 in (Professional Round is a separate 2 1/4 in option). Standard-handle installed depth = 26 3/8 in. Calculation or inference: 24 + 3/4 + 1 5/8 = 26 3/8 in (standard handle configuration). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 44.75 in | ✓ Verified — retained secondary source · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf assets.skulytics.io | Page 15 | |
Value used by ExactFit44.75 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24 + 0.75 + 20 Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf 24 in chassis + assumed 3/4 in panel + 20 in door depth measured from front of panel at 90 degrees.Open original source ↗ All retained supporting links
Why this value was used24 in chassis + assumed 3/4 in panel + 20 in door depth measured from front of panel at 90 degrees. Calculation or inference: 24 + 0.75 + 20. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 18 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io | Page 16 | |
Value used by ExactFit18 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90272075.pdf Reviewed manufacturer dimensions for RS1884FLJE1: min_cutout_width_in = 18 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS1884FLJE1: min_cutout_width_in = 18 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 84 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 90272075.pdf In this configuration: | Ceiling height: 94 1/2" Product cavity height: 84" Toe kick: 2" Panel height: 81 7/8, Panel gap and opening clearance: 1/8" | 5Open original source ↗ Why this value was usedIn this configuration: | Ceiling height: 94 1/2" Product cavity height: 84" Toe kick: 2" Panel height: 81 7/8, Panel gap and opening clearance: 1/8" | 5 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io | Page 16 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 90272075.pdf Exact family table: minimum shallow cavity depth 25 in when services are outside cavity.Open original source ↗ Why this value was usedExact family table: minimum shallow cavity depth 25 in when services are outside cavity. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io | Page 16 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 90272075.pdf Exact family table: minimum cabinetry gap from edge of door panel 1/8 in.Open original source ↗ Why this value was usedExact family table: minimum cabinetry gap from edge of door panel 1/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — 90272075.pdf assets.skulytics.io | Page 16 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 90272075.pdf Exact family table: minimum cabinetry gap from edge of door panel 1/8 in.Open original source ↗ Why this value was usedExact family table: minimum cabinetry gap from edge of door panel 1/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0 in | ✓ Verified — retained secondary source · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf assets.skulytics.io | Page 15 | |
Value used by ExactFit0 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 84 - 84 = 0 in Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf Product height 84 in and cavity height 84 in; residual = 0 in.Open original source ↗ All retained supporting links
Why this value was usedProduct height 84 in and cavity height 84 in; residual = 0 in. Calculation or inference: 84 - 84 = 0 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.25 in | ✓ Verified — retained secondary source · Calculated/inferred | Fisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf assets.skulytics.io | Page 15 | |
Value used by ExactFit0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 25 - 24 - 3/4 = 1/4 in Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-PlanningGuide-en-RS1884F-RS2484F-RS3084-RS3684-IntegratedRefrigeration-0-90003672I-USCA.pdf Minimum shallow cavity depth 25 in, chassis depth excluding panel 24 in, standard panel 3/4 in; installed residual = 1/4 in.Open original source ↗ All retained supporting links
Why this value was usedMinimum shallow cavity depth 25 in, chassis depth excluding panel 24 in, standard panel 3/4 in; installed residual = 1/4 in. Calculation or inference: 25 - 24 - 3/4 = 1/4 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 4.3125 in | ? Conflicting sources — resolved | Fisher and Paykel measurement source — 90272075.pdf Publisher not recorded | Page 16 | |
Value used by ExactFit4.3125 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 90272075.pdf Model page: Minimum door clearance to adjacent wall (90°) 4 5/16" (110 mm). The generic door-swing table (90272075 p.26) prints 5 5/16" but also 110 mm, so its inch figure is a typo; that table also swaps the 30"/36" columns at 115°. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedModel page: Minimum door clearance to adjacent wall (90°) 4 5/16" (110 mm). The generic door-swing table (90272075 p.26) prints 5 5/16" but also 110 mm, so its inch figure is a typo; that table also swaps the 30"/36" columns at 115°. Other evidence found
Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | 11.5 in | ? Verified — finalized database measurement | Fisher and Paykel measurement source — 90272075.pdf Publisher not recorded | Page 26 | |
Value used by ExactFit11.5 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — 90272075.pdf Door fully open to 115 degrees with the 1 5/8 in handle fitted: 11 1/2 in. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedDoor fully open to 115 degrees with the 1 5/8 in handle fitted: 11 1/2 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 17.75 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 90272075.pdf assets.skulytics.io | Page 16 | |
Value used by ExactFit17.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90272075.pdf Reviewed manufacturer dimensions for RS1884FLJE1: case_width_in = 17.75 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RS1884FLJE1: case_width_in = 17.75 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 4.3125 in. Earlier retained values: 5.3125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Model page: Minimum door clearance to adjacent wall (90°) 4 5/16" (110 mm). The generic door-swing table (90272075 p.26) prints 5 5/16" but also 110 mm, so its inch figure is a typo; that table also swaps the 30"/36" columns at 115°.
View source scope, location, and impact on fitassets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: RS1884FLJE1. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
12 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Wall clearance for door open to 90°; Wall clearance for fully open door; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: RS1884FLJE1. Publication/revision date: Not recorded. Reviewed: 2026-09-10.
5 displayed measurements supported: Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-15. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.