Measurement evidence for Fisher and Paykel RF203QDUVX1

Value used by ExactFit

35.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 74493569.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RF203QDUVX1: width_doors_closed_in = 35.625 in

Why this value was used

Reviewed manufacturer dimensions for RF203QDUVX1: width_doors_closed_in = 35.625 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.0625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 74493569.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height to top of chassis: 69 1/16 in.

Why this value was used

Height to top of chassis: 69 1/16 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 74493569.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-14

Overall height of fridge 70 1/2" (mounted feet included); height to top of hinge cover 69 7/8". The stored field holds the appliance's highest point (owner rule).

Why this value was used

Overall height of fridge 70 1/2" (mounted feet included); height to top of hinge cover 69 7/8". The stored field holds the appliance's highest point (owner rule).

Other evidence found

• 69.875 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Height to top of hinge cover: 69 7/8 in.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 74493569.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RF203QDUVX1: depth_case_only_in = 24 in

Why this value was used

Reviewed manufacturer dimensions for RF203QDUVX1: depth_case_only_in = 24 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

27.0625 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 74493569.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RF203QDUVX1: depth_less_handles_in = 27.0625 in

Why this value was used

Reviewed manufacturer dimensions for RF203QDUVX1: depth_less_handles_in = 27.0625 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

28.6875 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 74493569.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RF203QDUVX1: depth_with_handles_in = 28.6875 in

Why this value was used

Reviewed manufacturer dimensions for RF203QDUVX1: depth_with_handles_in = 28.6875 in

Other evidence found

• 27.0625 in — superseded

  www.ajmadison.com; location not retained. Model scope: not separately recorded. Raw value: Plain exact-model specification row: Depth = 27.0625 in | her & Paykel RF203QDUVX1 36 Inch Counter Depth Freestanding 4 ... Product Dimensions. Width: 35 5/8". Depth: 27 1/16". Depth (Excluding handles):. 27 1/16". Height: 70 1/2". Height to top of cabinet: 69 7/8 . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

42.6875 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 74493574.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 11
Reviewed: 2026-09-04

Manufacturer installation guide gives total depth from rear at 90 degrees: 42 11/16 in.

Why this value was used

Manufacturer installation guide gives total depth from rear at 90 degrees: 42 11/16 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

37.1875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 74493574.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 11
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RF203QDUVX1: min_cutout_width_in = 37.1875 in

Why this value was used

Reviewed manufacturer dimensions for RF203QDUVX1: min_cutout_width_in = 37.1875 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

71.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 74493574.pdf
manualspro.net · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 11
Reviewed: 2026-09-09

Exact-model installation table, Cabinetry Dimensions (including minimum air clearances): Inside height of cavity 71 1/4 in.

Why this value was used

Exact-model installation table, Cabinetry Dimensions (including minimum air clearances): Inside height of cavity 71 1/4 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25.1875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 74493574.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 11
Reviewed: 2026-09-09

Exact-model installation table: Flush with refrigerator chassis - full door rotation, Inside depth 25 3/16 in.

Why this value was used

Exact-model installation table: Flush with refrigerator chassis - full door rotation, Inside depth 25 3/16 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.8125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 74493574.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 11
Reviewed: 2026-09-09

Exact-model Minimum Clearances table: Side clearance 13/16 in.

Why this value was used

Exact-model Minimum Clearances table: Side clearance 13/16 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.8125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 74493574.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 11
Reviewed: 2026-09-09

Exact-model Minimum Clearances table: Side clearance 13/16 in.

Why this value was used

Exact-model Minimum Clearances table: Side clearance 13/16 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_height_in - overall_product_height (71.25 - 70.5)

Confidence label: high.

Calculation inputs: Minimum cutout height;

Primary evidence

Fisher and Paykel measurement source — 74493574.pdf
manualspro.net · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 11
Reviewed: 2026-09-09

Exact-model table prints 71 1/4 in inside cavity height and 70 1/2 in overall product height; additive top residual is 3/4 in.

Why this value was used

Exact-model table prints 71 1/4 in inside cavity height and 70 1/2 in overall product height; additive top residual is 3/4 in. Calculation or inference: min_cutout_height_in - overall_product_height (71.25 - 70.5).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1.1875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 74493574.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 11
Reviewed: 2026-09-09

Exact-model Minimum Clearances table: Rear clearance (including evaporator tray) 1 3/16 in.

Why this value was used

Exact-model Minimum Clearances table: Rear clearance (including evaporator tray) 1 3/16 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.9375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 74493574.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 11
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in (90 degrees). Exact guide: hinge-side clearance flush with door at 90 degrees = 3 15/16 in.

Why this value was used

Migrated from hinge_side_wall_clearance_in (90 degrees). Exact guide: hinge-side clearance flush with door at 90 degrees = 3 15/16 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

13.375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 74493569.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-14

Minimum Clearances: side clearance installed flush with door, full rotation 3 15/16"; minimum side clearance to wall 13 3/8". The wall figure is stored for this wall-clearance field.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Minimum Clearances: side clearance installed flush with door, full rotation 3 15/16"; minimum side clearance to wall 13 3/8". The wall figure is stored for this wall-clearance field.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.625 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 74493569.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RF203QDUVX1: case_width_in = 35.625 in

Why this value was used

Reviewed manufacturer dimensions for RF203QDUVX1: case_width_in = 35.625 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.