This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Bottom Freezer · Counter-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-17. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 31.09375 in | ✓ Conflicting sources — resolved | Fisher and Paykel installation document — 90368803.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit31.09375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90368803.pdf Reviewed manufacturer dimensions for RF170WRHJX1: width_doors_closed_in = 31.0938 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RF170WRHJX1: width_doors_closed_in = 31.0938 in Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 67.5 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 90368803.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit67.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90368803.pdf Reviewed manufacturer dimensions for RF170WRHJX1: height_case_in = 67.5 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RF170WRHJX1: height_case_in = 67.5 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 67.5 in | ✓ Conflicting sources — resolved | Fisher and Paykel installation document — 90368803.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit67.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90368803.pdf Reviewed manufacturer dimensions for RF170WRHJX1: height_hinge_in = 67.5 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RF170WRHJX1: height_hinge_in = 67.5 in Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24.625 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 90368803.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit24.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90368803.pdf Reviewed manufacturer dimensions for RF170WRHJX1: depth_case_only_in = 24.625 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RF170WRHJX1: depth_case_only_in = 24.625 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 27.375 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 90368803.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit27.375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90368803.pdf Reviewed manufacturer dimensions for RF170WRHJX1: depth_less_handles_in = 27.375 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RF170WRHJX1: depth_less_handles_in = 27.375 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 29 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 90368803.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit29 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90368803.pdf Reviewed manufacturer dimensions for RF170WRHJX1: depth_with_handles_in = 29 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RF170WRHJX1: depth_with_handles_in = 29 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 56.6875 in | ✓ Verified — retained secondary source | Fisher and Paykel installation document — 90368803.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit56.6875 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90368803.pdf Reviewed manufacturer dimensions for RF170WRHJX1: depth_doors_open_90_in = 56.6875 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RF170WRHJX1: depth_doors_open_90_in = 56.6875 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 32.6875 in | ✓ Conflicting sources — resolved | Fisher and Paykel installation document — 90368803.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit32.6875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90368803.pdf Reviewed manufacturer dimensions for RF170WRHJX1: min_cutout_width_in = 32.6875 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RF170WRHJX1: min_cutout_width_in = 32.6875 in Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 68.5 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — FP-InstallGuide-en-RF170AD-RF170BL-RF170W-RF201AD-RF135B-FrenchDoorRefrigerator-0-867008C-US-CA.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit68.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-InstallGuide-en-RF170AD-RF170BL-RF170W-RF201AD-RF135B-FrenchDoorRefrigerator-0-867008C-US-CA.pdf Cabinetry dimensions (including minimum air clearances): inside height of cavity 68.5 in.Open original source ↗ All retained supporting links
Why this value was usedCabinetry dimensions (including minimum air clearances): inside height of cavity 68.5 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 24.4375 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — FP-InstallGuide-en-RF170AD-RF170BL-RF170W-RF201AD-RF135B-FrenchDoorRefrigerator-0-867008C-US-CA.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit24.4375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-InstallGuide-en-RF170AD-RF170BL-RF170W-RF201AD-RF135B-FrenchDoorRefrigerator-0-867008C-US-CA.pdf Flush with refrigerator chassis - full door rotation: inside depth 24 7/16 in.Open original source ↗ All retained supporting links
Why this value was usedFlush with refrigerator chassis - full door rotation: inside depth 24 7/16 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.8125 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — FP-InstallGuide-en-RF170AD-RF170BL-RF170W-RF201AD-RF135B-FrenchDoorRefrigerator-0-867008C-US-CA.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit0.8125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-InstallGuide-en-RF170AD-RF170BL-RF170W-RF201AD-RF135B-FrenchDoorRefrigerator-0-867008C-US-CA.pdf Minimum clearance dimensions: side clearance 13/16 in.Open original source ↗ All retained supporting links
Why this value was usedMinimum clearance dimensions: side clearance 13/16 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.8125 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — FP-InstallGuide-en-RF170AD-RF170BL-RF170W-RF201AD-RF135B-FrenchDoorRefrigerator-0-867008C-US-CA.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit0.8125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-InstallGuide-en-RF170AD-RF170BL-RF170W-RF201AD-RF135B-FrenchDoorRefrigerator-0-867008C-US-CA.pdf Minimum clearance dimensions: side clearance 13/16 in.Open original source ↗ All retained supporting links
Why this value was usedMinimum clearance dimensions: side clearance 13/16 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 2 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — FP-InstallGuide-en-RF170AD-RF170BL-RF170W-RF201AD-RF135B-FrenchDoorRefrigerator-0-867008C-US-CA.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-InstallGuide-en-RF170AD-RF170BL-RF170W-RF201AD-RF135B-FrenchDoorRefrigerator-0-867008C-US-CA.pdf Minimum clearance dimensions: top clearance - above refrigerator cabinet 2 in.Open original source ↗ All retained supporting links
Why this value was usedMinimum clearance dimensions: top clearance - above refrigerator cabinet 2 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1.1875 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — FP-InstallGuide-en-RF170AD-RF170BL-RF170W-RF201AD-RF135B-FrenchDoorRefrigerator-0-867008C-US-CA.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit1.1875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-InstallGuide-en-RF170AD-RF170BL-RF170W-RF201AD-RF135B-FrenchDoorRefrigerator-0-867008C-US-CA.pdf Minimum clearance dimensions: rear clearance (including rear compartment cover) 1 3/16 in.Open original source ↗ All retained supporting links
Why this value was usedMinimum clearance dimensions: rear clearance (including rear compartment cover) 1 3/16 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 3.5625 in | ✓ Verified — retained secondary source | Fisher and Paykel measurement source — FP-InstallGuide-en-RF170AD-RF170BL-RF170W-RF201AD-RF135B-FrenchDoorRefrigerator-0-867008C-US-CA.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit3.5625 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidenceFisher and Paykel measurement source — FP-InstallGuide-en-RF170AD-RF170BL-RF170W-RF201AD-RF135B-FrenchDoorRefrigerator-0-867008C-US-CA.pdf Migrated from hinge_side_wall_clearance_in (90 degrees). Minimum clearance dimensions: hinge side flush with door at 90 degree rotation 3 9/16 in.Open original source ↗ All retained supporting links
Why this value was usedMigrated from hinge_side_wall_clearance_in (90 degrees). Minimum clearance dimensions: hinge side flush with door at 90 degree rotation 3 9/16 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 31.09375 in | ✓ Conflicting sources — resolved | Fisher and Paykel installation document — 90368803.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit31.09375 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceFisher and Paykel installation document — 90368803.pdf Reviewed manufacturer dimensions for RF170WRHJX1: case_width_in = 31.0938 inOpen original source ↗ Why this value was usedReviewed manufacturer dimensions for RF170WRHJX1: case_width_in = 31.0938 in Other evidence found
Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 31.09375 in. Earlier retained values: 31.0938 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Reviewed manufacturer dimensions for RF170WRHJX1: width_doors_closed_in = 31.0938 in
View source scope, location, and impact on fitSelected: 67.5 in. Earlier retained values: 67.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Reviewed manufacturer dimensions for RF170WRHJX1: height_hinge_in = 67.5 in
View source scope, location, and impact on fitSelected: 32.6875 in. Earlier retained values: 52.5625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Reviewed manufacturer dimensions for RF170WRHJX1: min_cutout_width_in = 32.6875 in
View source scope, location, and impact on fitSelected: 31.09375 in. Earlier retained values: 31.0938 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Reviewed manufacturer dimensions for RF170WRHJX1: case_width_in = 31.0938 in
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: RF170WRHJX1. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
9 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: RF170WRHJX1. Publication/revision date: Not recorded. Reviewed: 2026-09-17.
7 displayed measurements supported: Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-17. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.