Measurement evidence for Fisher and Paykel RF170WDLUX5N

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to Fisher and Paykel RF170WDLUX5N fit check Check this model against your opening How ExactFit verifies measurements

Fisher and Paykel RF170WDLUX5N

Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Complete mixed evidence

0exact-model manufacturer values

5verified equivalent/same-chassis values

11secondary-source-only values

0values with unresolved source details

Last reviewed: 2026-09-05. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	31.125 in	✓ Secondary source only	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit 31.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Secondary source Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLUX5N: width_doors_closed_in = 31.125 in Open original source ↗ Why this value was used Reviewed manufacturer dimensions for RF170WDLUX5N: width_doors_closed_in = 31.125 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	67.75 in	✓ Secondary source only	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit 67.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Secondary source Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLUX5N: height_case_in = 67.75 in Open original source ↗ Why this value was used Reviewed manufacturer dimensions for RF170WDLUX5N: height_case_in = 67.75 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	67.75 in	✓ Secondary source only	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit 67.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Secondary source Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLUX5N: height_hinge_in = 67.75 in Open original source ↗ Why this value was used Reviewed manufacturer dimensions for RF170WDLUX5N: height_hinge_in = 67.75 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	24.625 in	✓ Conflicting sources — resolved	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit 24.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Secondary source Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLUX5N: depth_case_only_in = 24.625 in Open original source ↗ Why this value was used Reviewed manufacturer dimensions for RF170WDLUX5N: depth_case_only_in = 24.625 in Other evidence found 27.375 in — superseded 90368792.pdf (p.2); page 2. Model scope: not separately recorded. Raw value: C Overall depth of product (excludes handle & -> 27 3/8. The final reviewed registry supersedes this earlier audit value. Reviewed manufacturer dimensions for RF170WDLUX5N: depth_case_only_in = 24.625 in Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	27.375 in	✓ Secondary source only	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit 27.375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Secondary source Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLUX5N: depth_less_handles_in = 27.375 in Open original source ↗ Why this value was used Reviewed manufacturer dimensions for RF170WDLUX5N: depth_less_handles_in = 27.375 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	29 in	✓ Secondary source only	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit 29 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Secondary source Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLUX5N: depth_with_handles_in = 29 in Open original source ↗ Why this value was used Reviewed manufacturer dimensions for RF170WDLUX5N: depth_with_handles_in = 29 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	56.6875 in	✓ Secondary source only	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit 56.6875 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Secondary source Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLUX5N: depth_doors_open_90_in = 56.6875 in Open original source ↗ Why this value was used Reviewed manufacturer dimensions for RF170WDLUX5N: depth_doors_open_90_in = 56.6875 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	32.6875 in	✓ Conflicting sources — resolved	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit 32.6875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Secondary source Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLUX5N: min_cutout_width_in = 32.6875 in Open original source ↗ Why this value was used Reviewed manufacturer dimensions for RF170WDLUX5N: min_cutout_width_in = 32.6875 in Other evidence found 52.5625 in — superseded 90368792.pdf (p.2); page 2. Model scope: not separately recorded. Raw value: A Width of cavity -> 52 9/16. The final reviewed registry supersedes this earlier audit value. Reviewed manufacturer dimensions for RF170WDLUX5N: min_cutout_width_in = 32.6875 in Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	69.75 in	✓ Verified — equivalent model · Calculated/inferred	Fisher Paykel RF170WDRUX5N User Guide assets.skulytics.io	Page 13
Value used by ExactFit 69.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidence Fisher Paykel RF170WDRUX5N User Guide assets.skulytics.io · User Guide Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 13 Reviewed: 2026-09-05 Minimum opening height derived from highest stored appliance endpoint 67.75 in plus documented top clearance 2.0 in. Open original source ↗ Why this value was used Minimum opening height derived from highest stored appliance endpoint 67.75 in plus documented top clearance 2.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Why evidence from RF170WDRUX5N applies Target model: RF170WDLUX5N. Supporting model: RF170WDRUX5N. Manufacturer: Fisher and Paykel. Product family and measurement relationship: max(height_case_in,height_hinge_in) + top_clearance_in. Measurement transferred: Minimum cutout height. Relevant equivalence evidence: Minimum opening height derived from highest stored appliance endpoint 67.75 in plus documented top clearance 2.0 in.. Known differences: not separately recorded. Review decision: calculated formula; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	25.813 in	✓ Verified — equivalent model · Calculated/inferred	Fisher Paykel RF170WDRUX5N Quick Reference guide assets.skulytics.io	Page 2
Value used by ExactFit 25.813 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidence Fisher Paykel RF170WDRUX5N Quick Reference guide assets.skulytics.io · Quick Reference guide Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 Minimum opening depth derived from case-only depth 24.625 in plus documented rear clearance 1.188 in. Open original source ↗ Why this value was used Minimum opening depth derived from case-only depth 24.625 in plus documented rear clearance 1.188 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Why evidence from RF170WDRUX5N applies Target model: RF170WDLUX5N. Supporting model: RF170WDRUX5N. Manufacturer: Fisher and Paykel. Product family and measurement relationship: depth_case_only_in + rear_clearance_in. Measurement transferred: Minimum cutout depth. Relevant equivalence evidence: Minimum opening depth derived from case-only depth 24.625 in plus documented rear clearance 1.188 in.. Known differences: not separately recorded. Review decision: calculated formula; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	1.188 in	✓ Verified — equivalent model · Calculated/inferred	Fisher Paykel RF170WDRUX5N Quick Reference guide assets.skulytics.io	Page 2
Value used by ExactFit 1.188 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from RF170WDRUX5N Confidence label: medium. Primary evidence Fisher Paykel RF170WDRUX5N Quick Reference guide assets.skulytics.io · Quick Reference guide Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 Conflict-free identical-chassis propagation from Fisher_Paykel RF170WDRUX5N: side_ventilation_clearance_in=1.188 in. Open original source ↗ Why this value was used Conflict-free identical-chassis propagation from Fisher_Paykel RF170WDRUX5N: side_ventilation_clearance_in=1.188 in. Calculation or inference: identical 8-dimension chassis signature; propagated from RF170WDRUX5N. Why evidence from RF170WDRUX5N applies Target model: RF170WDLUX5N. Supporting model: RF170WDRUX5N. Manufacturer: Fisher and Paykel. Product family and measurement relationship: identical 8-dimension chassis signature; propagated from RF170WDRUX5N. Measurement transferred: Left-side ventilation clearance. Relevant equivalence evidence: Conflict-free identical-chassis propagation from Fisher_Paykel RF170WDRUX5N: side_ventilation_clearance_in=1.188 in.. Known differences: not separately recorded. Review decision: identical chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	1.188 in	✓ Verified — equivalent model · Calculated/inferred	Fisher Paykel RF170WDRUX5N Quick Reference guide assets.skulytics.io	Page 2
Value used by ExactFit 1.188 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from RF170WDRUX5N Confidence label: medium. Primary evidence Fisher Paykel RF170WDRUX5N Quick Reference guide assets.skulytics.io · Quick Reference guide Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 Conflict-free identical-chassis propagation from Fisher_Paykel RF170WDRUX5N: side_ventilation_clearance_in=1.188 in. Open original source ↗ Why this value was used Conflict-free identical-chassis propagation from Fisher_Paykel RF170WDRUX5N: side_ventilation_clearance_in=1.188 in. Calculation or inference: identical 8-dimension chassis signature; propagated from RF170WDRUX5N. Why evidence from RF170WDRUX5N applies Target model: RF170WDLUX5N. Supporting model: RF170WDRUX5N. Manufacturer: Fisher and Paykel. Product family and measurement relationship: identical 8-dimension chassis signature; propagated from RF170WDRUX5N. Measurement transferred: Right-side ventilation clearance. Relevant equivalence evidence: Conflict-free identical-chassis propagation from Fisher_Paykel RF170WDRUX5N: side_ventilation_clearance_in=1.188 in.. Known differences: not separately recorded. Review decision: identical chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	2 in	✓ Verified — equivalent model · Calculated/inferred	Fisher Paykel RF170WDRUX5N User Guide assets.skulytics.io	Page 13
Value used by ExactFit 2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from RF170WDRUX5N Confidence label: medium. Primary evidence Fisher Paykel RF170WDRUX5N User Guide assets.skulytics.io · User Guide Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 13 Reviewed: 2026-09-05 Conflict-free identical-chassis propagation from Fisher_Paykel RF170WDRUX5N: top_clearance_in=2.0 in. Open original source ↗ Why this value was used Conflict-free identical-chassis propagation from Fisher_Paykel RF170WDRUX5N: top_clearance_in=2.0 in. Calculation or inference: identical 8-dimension chassis signature; propagated from RF170WDRUX5N. Why evidence from RF170WDRUX5N applies Target model: RF170WDLUX5N. Supporting model: RF170WDRUX5N. Manufacturer: Fisher and Paykel. Product family and measurement relationship: identical 8-dimension chassis signature; propagated from RF170WDRUX5N. Measurement transferred: Top clearance. Relevant equivalence evidence: Conflict-free identical-chassis propagation from Fisher_Paykel RF170WDRUX5N: top_clearance_in=2.0 in.. Known differences: not separately recorded. Review decision: identical chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	1.188 in	✓ Verified — equivalent model · Calculated/inferred	Fisher Paykel RF170WDRUX5N Quick Reference guide assets.skulytics.io	Page 2
Value used by ExactFit 1.188 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from RF170WDRUX5N Confidence label: medium. Primary evidence Fisher Paykel RF170WDRUX5N Quick Reference guide assets.skulytics.io · Quick Reference guide Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 Conflict-free identical-chassis propagation from Fisher_Paykel RF170WDRUX5N: rear_clearance_in=1.188 in. Open original source ↗ Why this value was used Conflict-free identical-chassis propagation from Fisher_Paykel RF170WDRUX5N: rear_clearance_in=1.188 in. Calculation or inference: identical 8-dimension chassis signature; propagated from RF170WDRUX5N. Why evidence from RF170WDRUX5N applies Target model: RF170WDLUX5N. Supporting model: RF170WDRUX5N. Manufacturer: Fisher and Paykel. Product family and measurement relationship: identical 8-dimension chassis signature; propagated from RF170WDRUX5N. Measurement transferred: Rear clearance. Relevant equivalence evidence: Conflict-free identical-chassis propagation from Fisher_Paykel RF170WDRUX5N: rear_clearance_in=1.188 in.. Known differences: not separately recorded. Review decision: identical chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Hinge-side wall clearance	1.968 in	✓ Secondary source only	Fisher Paykel RF170WDLUX5N Installation Guide - Quick Reference EN assets.skulytics.io	Page 1
Value used by ExactFit 1.968 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide - Quick Reference EN assets.skulytics.io · Installation Guide - Quick Reference EN Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Refrigerator weight on hinge side foot \| 50 mm gap (2") \| Your refrigerator has a variety of Open original source ↗ Why this value was used Refrigerator weight on hinge side foot \| 50 mm gap (2") \| Your refrigerator has a variety of Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	31.125 in	✓ Secondary source only	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit 31.125 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Secondary source Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLUX5N: case_width_in = 31.125 in Open original source ↗ Why this value was used Reviewed manufacturer dimensions for RF170WDLUX5N: case_width_in = 31.125 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Adjoining-wall clearance (reviewed endpoint)	3.5625 in	✓ Conflicting sources — resolved	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit 3.5625 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Secondary source Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLUX5N: side_clearance_wall_in = 3.5625 in Open original source ↗ Why this value was used Reviewed manufacturer dimensions for RF170WDLUX5N: side_clearance_wall_in = 3.5625 in Other evidence found 1.1875 in — superseded 90368793.pdf; page 2. Model scope: not separately recorded. Raw value: clearance each side 1 3/16 ". The final reviewed registry supersedes this earlier audit value. Reviewed manufacturer dimensions for RF170WDLUX5N: side_clearance_wall_in = 3.5625 in Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Depth without door

Selected: 24.625 in. Earlier retained values: 27.375 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Reviewed manufacturer dimensions for RF170WDLUX5N: depth_case_only_in = 24.625 in

View source scope, location, and impact on fit

Minimum cutout width

Selected: 32.6875 in. Earlier retained values: 52.5625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Reviewed manufacturer dimensions for RF170WDLUX5N: min_cutout_width_in = 32.6875 in

View source scope, location, and impact on fit

Adjoining-wall clearance (reviewed endpoint)

Selected: 3.5625 in. Earlier retained values: 1.1875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Reviewed manufacturer dimensions for RF170WDLUX5N: side_clearance_wall_in = 3.5625 in

View source scope, location, and impact on fit

Source documents and pages

Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN

assets.skulytics.io · Installation Guide Refrigerator Freezer EN · secondary model/source

Model numbers covered: RF170WDLUX5N. Publication/revision date: Not recorded. Reviewed: 2026-09-04.

10 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Cabinet case width; Adjoining-wall clearance (reviewed endpoint).

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Fisher Paykel RF170WDRUX5N User Guide

assets.skulytics.io · User Guide · equivalent model/source

Model numbers covered: RF170WDRUX5N. Publication/revision date: Not recorded. Reviewed: 2026-09-05.

2 displayed measurements supported: Minimum cutout height; Top clearance.

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Fisher Paykel RF170WDRUX5N Quick Reference guide

assets.skulytics.io · Quick Reference guide · equivalent model/source

Model numbers covered: RF170WDRUX5N. Publication/revision date: Not recorded. Reviewed: 2026-09-05.

4 displayed measurements supported: Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Rear clearance.

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Fisher Paykel RF170WDLUX5N Installation Guide - Quick Reference EN

assets.skulytics.io · Installation Guide - Quick Reference EN · secondary model/source

Model numbers covered: RF170WDLUX5N. Publication/revision date: Not recorded. Reviewed: 2026-09-05.

1 displayed measurements supported: Hinge-side wall clearance.

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Report a problem with this model Check whether RF170WDLUX5N fits your opening Back to Fisher and Paykel RF170WDLUX5N Read the full verification methodology

Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.

Evidence summary

Complete mixed evidence

Measurements and supporting evidence

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Why evidence from RF170WDRUX5N applies

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Why evidence from RF170WDRUX5N applies

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Why evidence from RF170WDRUX5N applies

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Why evidence from RF170WDRUX5N applies

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Why evidence from RF170WDRUX5N applies

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Why evidence from RF170WDRUX5N applies

Other evidence found

Effect on fit result

Value used by ExactFit