Measurement evidence for Fisher and Paykel RF170WDLJX5

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to Fisher and Paykel RF170WDLJX5 fit check Check this model against your opening How ExactFit verifies measurements

Fisher and Paykel RF170WDLJX5

Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Incomplete evidence

0exact-model manufacturer values

0verified equivalent/same-chassis values

3secondary-source-only values

13values with unresolved source details

Last reviewed: 2026-09-05. 3 retained source records. 0 unresolved conflicts. Not every fit-critical input is supported.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.

ExactFit does not have sufficient evidence for every fit-critical measurement. The fit checker will return Uncertain unless a known measurement already proves that the model does not fit.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	Unknown	? Not found	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit Unknown · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Not established Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLJX5: width_doors_closed_in = 31.0938 in Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 31.09375 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found 31.0938 in — superseded 74613303.pdf; page 1. Model scope: not separately recorded. Raw value: Width 31 3/32". The final reviewed registry supersedes this earlier audit value. Reviewed manufacturer dimensions for RF170WDLJX5: width_doors_closed_in = 31.0938 in Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	Unknown	? Not found	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit Unknown · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Not established Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLJX5: height_case_in = 67.5 in Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 67.5 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	Unknown	? Not found	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit Unknown · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Not established Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLJX5: height_hinge_in = 67.5 in Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 67.5 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found 67.75 in — superseded 74613307.pdf; page 13. Model scope: not separately recorded. Raw value: A Overall height of product: 67.75 in \| A Overall height of product \| 67 3/4" (1720) \| 67 3/4" (1720). The final reviewed registry supersedes this earlier audit value. Reviewed manufacturer dimensions for RF170WDLJX5: height_hinge_in = 67.5 in Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	Unknown	? Not found	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit Unknown · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Not established Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLJX5: depth_case_only_in = 24.625 in Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 24.625 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	Unknown	? Not found	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit Unknown · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Not established Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLJX5: depth_less_handles_in = 27.375 in Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 27.375 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	Unknown	? Not found	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit Unknown · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Not established Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLJX5: depth_with_handles_in = 29 in Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 29 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	Unknown	? Not found	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit Unknown · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Not established Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLJX5: depth_doors_open_90_in = 56.6875 in Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 56.6875 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	Unknown	? Not found	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit Unknown · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Not established Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLJX5: min_cutout_width_in = 32.6875 in Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 32.6875 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found 52.5625 in — superseded 74613309.pdf (p.4); page 4. Model scope: not separately recorded. Raw value: A Width of cavity -> 52 9/16. The final reviewed registry supersedes this earlier audit value. Reviewed manufacturer dimensions for RF170WDLJX5: min_cutout_width_in = 32.6875 in Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	Unknown	? Not found · Calculated/inferred	Fisher Paykel RF170WDLJX5 User Guide assets.skulytics.io	Page 13
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidence Fisher Paykel RF170WDLJX5 User Guide assets.skulytics.io · User Guide Model scope: Not established Publication/revision date: Not recorded Location: Page 13 Reviewed: 2026-09-05 Minimum opening height derived from highest stored appliance endpoint 67.5 in plus documented top clearance 2.0 in. Open original source ↗ Why this value was used A required calculation input lacks defensible evidence. Retained research value: 69.5 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	Unknown	? Not found · Calculated/inferred	Fisher Paykel RF170WDLJX5 User Guide assets.skulytics.io	Page 13
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidence Fisher Paykel RF170WDLJX5 User Guide assets.skulytics.io · User Guide Model scope: Not established Publication/revision date: Not recorded Location: Page 13 Reviewed: 2026-09-05 Minimum opening depth derived from case-only depth 24.625 in plus documented rear clearance 1.188 in. Open original source ↗ Why this value was used A required calculation input lacks defensible evidence. Retained research value: 25.813 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	Unknown	? Not found · Calculated/inferred	Fisher Paykel RF170ADUSX4N Quick Reference guide assets.skulytics.io	Page 2
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: model-series prefix RF170; 5 direct seeds; unanimous value 1.188 Confidence label: medium. Primary evidence Fisher Paykel RF170ADUSX4N Quick Reference guide assets.skulytics.io · Quick Reference guide Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 Conflict-free 5-character model-series consensus (RF170) from 5 directly evidenced models; example Fisher_Paykel RF170ADUSX4N: Minimum air clearance - each \| 1 3/16" \| Width Open original source ↗ Why this value was used A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement. Retained research value: 1.188 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	Unknown	? Not found · Calculated/inferred	Fisher Paykel RF170ADUSX4N Quick Reference guide assets.skulytics.io	Page 2
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: model-series prefix RF170; 5 direct seeds; unanimous value 1.188 Confidence label: medium. Primary evidence Fisher Paykel RF170ADUSX4N Quick Reference guide assets.skulytics.io · Quick Reference guide Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 Conflict-free 5-character model-series consensus (RF170) from 5 directly evidenced models; example Fisher_Paykel RF170ADUSX4N: Minimum air clearance - each \| 1 3/16" \| Width Open original source ↗ Why this value was used A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement. Retained research value: 1.188 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	2 in	✓ Secondary source only	Fisher Paykel RF170WDLJX5 User Guide assets.skulytics.io	Page 13
Value used by ExactFit 2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLJX5 User Guide assets.skulytics.io · User Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 13 Reviewed: 2026-09-05 P Top clearance — above refrigerator cabinet \| 2" (50) \| 2" (50) Open original source ↗ Why this value was used P Top clearance — above refrigerator cabinet \| 2" (50) \| 2" (50) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	1.188 in	✓ Secondary source only	Fisher Paykel RF170WDLJX5 User Guide assets.skulytics.io	Page 13
Value used by ExactFit 1.188 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLJX5 User Guide assets.skulytics.io · User Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 13 Reviewed: 2026-09-05 N Rear clearance (incl. rear compartment cover) \| 1 3/16" (30) \| 1 3/16" (30) Open original source ↗ Why this value was used N Rear clearance (incl. rear compartment cover) \| 1 3/16" (30) \| 1 3/16" (30) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Hinge-side wall clearance	3.562 in	✓ Secondary source only	Fisher Paykel RF170WDLJX5 User Guide assets.skulytics.io	Page 13
Value used by ExactFit 3.562 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLJX5 User Guide assets.skulytics.io · User Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 13 Reviewed: 2026-09-05 M Side clearance — hinge side flush with door — 90° rotation \| 3 9/16" (90) \| 3 9/16" (90) Open original source ↗ Why this value was used M Side clearance — hinge side flush with door — 90° rotation \| 3 9/16" (90) \| 3 9/16" (90) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	Unknown	? Not found	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit Unknown · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Not established Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLJX5: case_width_in = 31.0938 in Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 31.09375 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found 31.0938 in — superseded 74613303.pdf; page 1. Model scope: not separately recorded. Raw value: Width 31 3/32". The final reviewed registry supersedes this earlier audit value. Reviewed manufacturer dimensions for RF170WDLJX5: case_width_in = 31.0938 in Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Adjoining-wall clearance (reviewed endpoint)	Unknown	? Not found	Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io	Page 9
Value used by ExactFit Unknown · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN assets.skulytics.io · Installation Guide Refrigerator Freezer EN Model scope: Not established Publication/revision date: Not recorded Location: Page 9 Reviewed: 2026-09-04 Reviewed manufacturer dimensions for RF170WDLJX5: side_clearance_wall_in = 3.5625 in Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 3.5625 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found 0.812 in — superseded 74613307.pdf; page 13. Model scope: not separately recorded. Raw value: K Side clearance: 0.812 in \| K Side clearance \| 13/16" (20) \| 13/16" (20). The final reviewed registry supersedes this earlier audit value. Reviewed manufacturer dimensions for RF170WDLJX5: side_clearance_wall_in = 3.5625 in Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Overall width

Selected: Unknown. Earlier retained values: 31.0938 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

View source scope, location, and impact on fit

Height with hinge / controlling height

Selected: Unknown. Earlier retained values: 67.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

View source scope, location, and impact on fit

Minimum cutout width

Selected: Unknown. Earlier retained values: 52.5625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

View source scope, location, and impact on fit

Cabinet case width

Selected: Unknown. Earlier retained values: 31.0938 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

View source scope, location, and impact on fit

Adjoining-wall clearance (reviewed endpoint)

Selected: Unknown. Earlier retained values: 0.812 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

View source scope, location, and impact on fit

Measurements not established

Overall width

Not found for safe fit use. Sources retained: 90368803.pdf. Related-model record: RF170WDLUX5N.

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Cabinet height

Not found for safe fit use. Sources retained: 90368803.pdf. Related-model record: RF170WDLUX5N.

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Height with hinge / controlling height

Not found for safe fit use. Sources retained: 90368803.pdf. Related-model record: RF170WDLUX5N.

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Depth without door

Not found for safe fit use. Sources retained: 90368803.pdf. Related-model record: RF170WDLUX5N.

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Depth with door, without handles

Not found for safe fit use. Sources retained: 90368803.pdf. Related-model record: RF170WDLUX5N.

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.

Depth with handle

Not found for safe fit use. Sources retained: 90368803.pdf. Related-model record: RF170WDLUX5N.

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.

Depth with doors open at 90°

Not found for safe fit use. Sources retained: 90368803.pdf. Related-model record: RF170WDLUX5N.

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.

Minimum cutout width

Not found for safe fit use. Sources retained: 90368803.pdf. Related-model record: RF170WDLUX5N.

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Minimum cutout height

Not found for safe fit use. Sources retained: 74613304.pdf. Related-model record: RF170WDLJX5.

A required calculation input lacks defensible evidence.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Minimum cutout depth

Not found for safe fit use. Sources retained: 74613304.pdf. Related-model record: RF170WDLJX5.

A required calculation input lacks defensible evidence.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Left-side ventilation clearance

Not found for safe fit use. Sources retained: 82594893.pdf. Related-model record: RF170ADUSX4N.

A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Right-side ventilation clearance

Not found for safe fit use. Sources retained: 82594893.pdf. Related-model record: RF170ADUSX4N.

A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Cabinet case width

Not found for safe fit use. Sources retained: 90368803.pdf. Related-model record: RF170WDLUX5N.

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.

Adjoining-wall clearance (reviewed endpoint)

Not found for safe fit use. Sources retained: 90368803.pdf. Related-model record: RF170WDLUX5N.

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.

Source documents and pages

Fisher Paykel RF170WDLUX5N Installation Guide Refrigerator Freezer EN

assets.skulytics.io · Installation Guide Refrigerator Freezer EN · Scope not established

Model numbers covered: RF170WDLUX5N. Publication/revision date: Not recorded. Reviewed: 2026-09-04.

10 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Cabinet case width; Adjoining-wall clearance (reviewed endpoint).

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Fisher Paykel RF170WDLJX5 User Guide

assets.skulytics.io · User Guide · secondary model/source

Model numbers covered: RF170WDLJX5. Publication/revision date: Not recorded. Reviewed: 2026-09-05.

5 displayed measurements supported: Minimum cutout height; Minimum cutout depth; Top clearance; Rear clearance; Hinge-side wall clearance.

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Fisher Paykel RF170ADUSX4N Quick Reference guide

assets.skulytics.io · Quick Reference guide · Scope not established

Model numbers covered: RF170ADUSX4N. Publication/revision date: Not recorded. Reviewed: 2026-09-05.

2 displayed measurements supported: Left-side ventilation clearance; Right-side ventilation clearance.

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Report a problem with this model Check whether RF170WDLJX5 fits your opening Back to Fisher and Paykel RF170WDLJX5 Read the full verification methodology

Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.

Evidence summary

Incomplete evidence

Measurements and supporting evidence

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence