Measurement evidence for Fisher and Paykel RB2470BRV2

Value used by ExactFit

23.46875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 105850772.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 9
Reviewed: 2026-10-13

G Width of custom panel 23 15/32" (596 mm). Integrated column: closed width measured across the installed panel (owner decision 2026-09-24).

Why this value was used

G Width of custom panel 23 15/32" (596 mm). Integrated column: closed width measured across the installed panel (owner decision 2026-09-24).

Other evidence found

• 21.6875 in — superseded

  Document 105850774.pdf (p.5); page 5. Model scope: not separately recorded. Raw value: B Overall width of product -> 21 11/16. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 105850772.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RB2470BRV2: height_case_in = 69.75 in

Why this value was used

Reviewed manufacturer dimensions for RB2470BRV2: height_case_in = 69.75 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 105850772.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RB2470BRV2: height_hinge_in = 69.75 in

Why this value was used

Reviewed manufacturer dimensions for RB2470BRV2: height_hinge_in = 69.75 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

21.6875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 105850772.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RB2470BRV2: depth_case_only_in = 21.6875 in

Why this value was used

Reviewed manufacturer dimensions for RB2470BRV2: depth_case_only_in = 21.6875 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

22.4375 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 21 11/16 + 3/4 = 22 7/16 in

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — FP-PlanningGuide-en-RB2470BRV2-IntegratedRefrigeratorFreezer-0-90004874B-US-CA.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-10

Exact RB2470BRV2 planning data sheet: chassis depth excluding custom panels and handle is 21 11/16 in; custom-panel range is 5/8 to 7/8 in. Standard documented 3/4 in panel scenario gives installed depth excluding handle 22 7/16 in.

Why this value was used

Exact RB2470BRV2 planning data sheet: chassis depth excluding custom panels and handle is 21 11/16 in; custom-panel range is 5/8 to 7/8 in. Standard documented 3/4 in panel scenario gives installed depth excluding handle 22 7/16 in. Calculation or inference: 21 11/16 + 3/4 = 22 7/16 in.

Other evidence found

• 21.6875 in — superseded

  Document 105850774.pdf (p.5); page 5. Model scope: not separately recorded. Raw value: C Overall depth of product excluding front -> 21 11/16. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

24.0625 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 21 11/16 + 3/4 + 1 5/8 = 24 1/16 in

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — contemporary-round-handle-kit-for-integrated-refrigerator-freezer-24in-ahsrd70b-25385.html
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-10

Exact RB2470BRV2 data sheet gives chassis depth 21 11/16 in and permits a 3/4 in custom panel. Official AHSRD70B page visibly states compatibility with RB2470B and handle depth 1 5/8 in. Standard 3/4 in panel plus compatible handle gives 24 1/16 in.

Why this value was used

Exact RB2470BRV2 data sheet gives chassis depth 21 11/16 in and permits a 3/4 in custom panel. Official AHSRD70B page visibly states compatibility with RB2470B and handle depth 1 5/8 in. Standard 3/4 in panel plus compatible handle gives 24 1/16 in. Calculation or inference: 21 11/16 + 3/4 + 1 5/8 = 24 1/16 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

45.0625 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 21 11/16 + 22 5/8 + 3/4 = 45 1/16 in

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — FP-PlanningGuide-en-RB2470BRV2-IntegratedRefrigeratorFreezer-0-90004874B-US-CA.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-10

Exact RB2470BRV2 planning data sheet shows chassis depth 21 11/16 in and dimension G, inner door open at 90 degrees from the front of the carcass excluding custom panel and handle, as 22 5/8 in. Adding the explicitly selected 3/4 in panel gives total installed rear-to-open-front depth 45 1/16 in.

Why this value was used

Exact RB2470BRV2 planning data sheet shows chassis depth 21 11/16 in and dimension G, inner door open at 90 degrees from the front of the carcass excluding custom panel and handle, as 22 5/8 in. Adding the explicitly selected 3/4 in panel gives total installed rear-to-open-front depth 45 1/16 in. Calculation or inference: 21 11/16 + 22 5/8 + 3/4 = 45 1/16 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

22.0625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 105850772.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-04

Cavity width begins at 22 1/16 in.

Why this value was used

Cavity width begins at 22 1/16 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 105850772.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-05

Exact planning guide: cavity height range begins at 70 in.

Why this value was used

Exact planning guide: cavity height range begins at 70 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

22.0625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 105850772.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-05

Exact planning guide: minimum cavity depth 22 1/16 in.

Why this value was used

Exact planning guide: minimum cavity depth 22 1/16 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.1875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 105850772.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-05

Legacy reviewed field migration; endpoint indicators=['cabinetry gap']; Conservative documented side cabinetry gap for the thicker supported custom-panel range: 3/16 in.

Why this value was used

Legacy reviewed field migration; endpoint indicators=['cabinetry gap']; Conservative documented side cabinetry gap for the thicker supported custom-panel range: 3/16 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.1875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 105850772.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-05

Legacy reviewed field migration; endpoint indicators=['cabinetry gap']; Conservative documented side cabinetry gap for the thicker supported custom-panel range: 3/16 in.

Why this value was used

Legacy reviewed field migration; endpoint indicators=['cabinetry gap']; Conservative documented side cabinetry gap for the thicker supported custom-panel range: 3/16 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 70 - 69 3/4 = 1/4 in

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — FP-PlanningGuide-en-RB2470BRV2-IntegratedRefrigeratorFreezer-0-90004874B-US-CA.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 5
Reviewed: 2026-09-10

Height of cavity 70 in minimum; overall height of product 69 3/4 in; residual = 1/4 in.

Why this value was used

Height of cavity 70 in minimum; overall height of product 69 3/4 in; residual = 1/4 in. Calculation or inference: 70 - 69 3/4 = 1/4 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 22 1/16 - 21 11/16 = 3/8 in

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — FP-PlanningGuide-en-RB2470BRV2-IntegratedRefrigeratorFreezer-0-90004874B-US-CA.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 5
Reviewed: 2026-09-10

Minimum cavity depth 22 1/16 in; product depth excluding front panels 21 11/16 in; residual = 3/8 in.

Why this value was used

Minimum cavity depth 22 1/16 in; product depth excluding front panels 21 11/16 in; residual = 3/8 in. Calculation or inference: 22 1/16 - 21 11/16 = 3/8 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

8.4375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Fisher and Paykel measurement source — 105850772.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in (fully open). Exact planning guide: inner door at 113 degrees extends 8 7/16 in from side of product for full internal access.

Why this value was used

Migrated from hinge_side_wall_clearance_in (fully open). Exact planning guide: inner door at 113 degrees extends 8 7/16 in from side of product for full internal access.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

21.6875 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Fisher and Paykel installation document — 105850772.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-04

Reviewed manufacturer dimensions for RB2470BRV2: case_width_in = 21.6875 in

Why this value was used

Reviewed manufacturer dimensions for RB2470BRV2: case_width_in = 21.6875 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.