This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-09-05. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux GRSS2652AF Product Specifications Sheet assets.skulytics.io · Product Specifications Sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux GRSS2652AF Product Specifications Sheet assets.skulytics.io · Product Specifications Sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux GRSS2652AF Product Specifications Sheet assets.skulytics.io · Product Specifications Sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux GRSS2652AF Product Specifications Sheet assets.skulytics.io · Product Specifications Sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux GRSS2652AF Product Specifications Sheet assets.skulytics.io · Product Specifications Sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux GRSS2652AF Product Specifications Sheet assets.skulytics.io · Product Specifications Sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux GRSS2652AF Product Specifications Sheet assets.skulytics.io · Product Specifications Sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Retained specification excerpt: Exact-model retailer specification: Cutout Width 35.875 in.
Value used by ExactFit
35.875 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux measurement source — https://www.brandsmartusa.com/products/appliances-refrigerators-side-by-side-refrigerators-grss2652af-ss www.brandsmartusa.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Exact-model retailer specification: Cutout Width 35.875 in. Reviewed: 2026-09-04
Exact-model retailer specification: Cutout Width 35.875 in.
Exact-model retailer specification: Cutout Width 35.875 in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Minimum opening height derived from highest stored appliance endpoint 69.875 in plus documented top clearance 0.375 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Minimum opening depth derived from case-only depth 28.75 in plus propagated rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.
Why evidence from FRSN2610AF applies
Target model: GRSS2652AF. Supporting model: FRSN2610AF. Manufacturer: Electrolux. Product family and measurement relationship: depth_case_only_in + rear_clearance_in.
Measurement transferred: Minimum cutout depth. Relevant equivalence evidence: Minimum opening depth derived from case-only depth 28.75 in plus propagated rear clearance 1.0 in.. Known differences: not separately recorded. Review decision: preserved documented inference; 2026-09-05.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux GRSS2652AF Complete Owner's Guide assets.skulytics.io · Complete Owner's Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-05
Manufacturer installation guide: Sides & Top clearance 3/8".
Manufacturer installation guide: Sides & Top clearance 3/8".
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux GRSS2652AF Complete Owner's Guide assets.skulytics.io · Complete Owner's Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-05
Manufacturer installation guide: Sides & Top clearance 3/8".
Manufacturer installation guide: Sides & Top clearance 3/8".
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux GRSS2652AF Complete Owner's Guide assets.skulytics.io · Complete Owner's Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-05
Manufacturer installation guide: Sides & Top clearance 3/8".
Manufacturer installation guide: Sides & Top clearance 3/8".
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Frigidaire FRSN2610AF
Confidence label: medium.
Primary evidence
Frigidaire FRSN2610AF Complete Owner's Guide assets.skulytics.io · Complete Owner's Guide Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 6 Reviewed: 2026-09-05
Conflict-free corporate-family exact 8-dimension chassis match to Frigidaire FRSN2610AF; original evidence: • Sides 3/8" (9.5mm) | • Back 1" (25.4mm) | 6
Conflict-free corporate-family exact 8-dimension chassis match to Frigidaire FRSN2610AF; original evidence: • Sides 3/8" (9.5mm) | • Back 1" (25.4mm) | 6 Calculation or inference: exact 8-dimension chassis signature; source model Frigidaire FRSN2610AF.
Why evidence from FRSN2610AF applies
Target model: GRSS2652AF. Supporting model: FRSN2610AF. Manufacturer: Electrolux. Product family and measurement relationship: exact 8-dimension chassis signature; source model Frigidaire FRSN2610AF.
Measurement transferred: Rear clearance. Relevant equivalence evidence: Conflict-free corporate-family exact 8-dimension chassis match to Frigidaire FRSN2610AF; original evidence: • Sides 3/8" (9.5mm) | • Back 1" (25.4mm) | 6. Known differences: not separately recorded. Review decision: preserved documented inference; 2026-09-05.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux GRSS2652AF Complete Owner's Guide assets.skulytics.io · Complete Owner's Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-05
Manufacturer manual documents 0.375 in side installation clearance. The hinge-wall note is conditional and gives no separate numeric minimum; the documented side baseline is retained.
Manufacturer manual documents 0.375 in side installation clearance. The hinge-wall note is conditional and gives no separate numeric minimum; the documented side baseline is retained.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux GRSS2652AF Product Specifications Sheet assets.skulytics.io · Product Specifications Sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux GRSS2652AF Complete Owner's Guide assets.skulytics.io · Complete Owner's Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-04
Manufacturer installation guide: Sides & Top clearance 3/8".
Model numbers covered: GRSS2652AF. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
8 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.