Measurement evidence for Electrolux ERMC2295AS

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to Electrolux ERMC2295AS fit check Check this model against your opening How ExactFit verifies measurements

Electrolux ERMC2295AS

French Door · Counter-depth
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Complete mixed evidence

0exact-model manufacturer values

0verified equivalent/same-chassis values

15secondary-source-only values

1values with unresolved source details

Last reviewed: 2026-10-04. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	36 in	✓ Verified — retained secondary source	Electrolux installation document — 74492253.pdf assets.skulytics.io	Page 2
Value used by ExactFit 36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Electrolux installation document — 74492253.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Width 36" Open original source ↗ Why this value was used Width 36" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	69.1 in	✓ Verified — retained secondary source	Electrolux installation document — 74492253.pdf assets.skulytics.io	Page 2
Value used by ExactFit 69.1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Electrolux installation document — 74492253.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Height Without Hinge 69.1" Open original source ↗ Why this value was used Height Without Hinge 69.1" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	70.2 in	✓ Verified — retained secondary source	Electrolux installation document — 74492253.pdf assets.skulytics.io	Page 2
Value used by ExactFit 70.2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Electrolux installation document — 74492253.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Height With Hinge 70 2/10" Open original source ↗ Why this value was used Height With Hinge 70 2/10" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	24.5 in	✓ Verified — retained secondary source	Electrolux installation document — 74492253.pdf assets.skulytics.io	Page 2
Value used by ExactFit 24.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Electrolux installation document — 74492253.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Depth of Cabinet 24 1/2" Open original source ↗ Why this value was used Depth of Cabinet 24 1/2" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	29.125 in	✓ Verified — retained secondary source	Electrolux installation document — 74492253.pdf assets.skulytics.io	Page 2
Value used by ExactFit 29.125 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Electrolux installation document — 74492253.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Depth With Door 29 1/8" Open original source ↗ Why this value was used Depth With Door 29 1/8" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	31.875 in	✓ Verified — retained secondary source	Electrolux installation document — 74492253.pdf assets.skulytics.io	Page 2
Value used by ExactFit 31.875 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Electrolux installation document — 74492253.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Depth With Door and Handle 31 7/8" Open original source ↗ Why this value was used Depth With Door and Handle 31 7/8" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	44.875 in	✓ Verified — retained secondary source	Electrolux installation document — 74492253.pdf assets.skulytics.io	Page 2
Value used by ExactFit 44.875 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Electrolux installation document — 74492253.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Depth With Door 90° Open 44 7/8" Open original source ↗ Why this value was used Depth With Door 90° Open 44 7/8" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	36 in	✓ Conflicting sources — resolved	Electrolux measurement source — 74492253.pdf www.ajmadison.com	Page 3
Value used by ExactFit 36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Electrolux measurement source — 74492253.pdf www.ajmadison.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-10-04 "Built-In Look" Cutout Dimensions: (A) 70 3/8" (B) 36" (C) 25". Replaces a calculated value. Open original source ↗ Why this value was used "Built-In Look" Cutout Dimensions: (A) 70 3/8" (B) 36" (C) 25". Replaces a calculated value. Other evidence found 36.625 in — superseded The same document as the value used above; page 2. Model scope: not separately recorded. Raw value: Calculated opening width from exact-model cabinet width 35.875 in plus two exact-model side installation clearances of 0.375 in; clearance source 103503878.pdf, page 7.. The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	70.375 in	✓ Conflicting sources — resolved	Electrolux measurement source — 74492253.pdf assets.skulytics.io	Page 3
Value used by ExactFit 70.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Electrolux measurement source — 74492253.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-10-04 "Built-In Look" Cutout Dimensions: (A) 70 3/8" (B) 36" (C) 25". Replaces a calculated value. Open original source ↗ Why this value was used "Built-In Look" Cutout Dimensions: (A) 70 3/8" (B) 36" (C) 25". Replaces a calculated value. Other evidence found 70.575 in — superseded The same document as the value used above; page 2. Model scope: not separately recorded. Raw value: Calculated opening height from exact-model hinge height 70.2 in plus exact-model top clearance 0.375 in; clearance source 103503878.pdf, page 7.. The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	25 in	✓ Conflicting sources — resolved	Electrolux measurement source — 74492253.pdf www.ajmadison.com	Page 3
Value used by ExactFit 25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Electrolux measurement source — 74492253.pdf www.ajmadison.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-10-04 "Built-In Look" Cutout Dimensions: (A) 70 3/8" (B) 36" (C) 25". Replaces a calculated value. Open original source ↗ Why this value was used "Built-In Look" Cutout Dimensions: (A) 70 3/8" (B) 36" (C) 25". Replaces a calculated value. Other evidence found 25.5 in — superseded The same document as the value used above; page 2. Model scope: not separately recorded. Raw value: Calculated opening depth from exact-model cabinet depth 24.5 in plus exact-model rear clearance 1 in; clearance source 103503878.pdf, page 7.. The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	0.375 in	✓ Verified — retained secondary source	Electrolux measurement source — 103503878.pdf assets.skulytics.io	Page 7
Value used by ExactFit 0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Electrolux measurement source — 103503878.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-05 • \| Sides & Top 3/8 in. (9.5 mm) \| • \| deterministic pattern: installation_sides Open original source ↗ Why this value was used • \| Sides & Top 3/8 in. (9.5 mm) \| • \| deterministic pattern: installation_sides Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	0.375 in	✓ Verified — retained secondary source	Electrolux measurement source — 103503878.pdf assets.skulytics.io	Page 7
Value used by ExactFit 0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Electrolux measurement source — 103503878.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-05 • \| Sides & Top 3/8 in. (9.5 mm) \| • \| deterministic pattern: installation_sides Open original source ↗ Why this value was used • \| Sides & Top 3/8 in. (9.5 mm) \| • \| deterministic pattern: installation_sides Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	0.375 in	✓ Verified — retained secondary source	Electrolux measurement source — 103503878.pdf assets.skulytics.io	Page 7
Value used by ExactFit 0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Electrolux measurement source — 103503878.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-05 • \| Sides & Top 3/8 in. (9.5 mm) \| • \| deterministic pattern: installation_sides Open original source ↗ Why this value was used • \| Sides & Top 3/8 in. (9.5 mm) \| • \| deterministic pattern: installation_sides Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	1 in	✓ Verified — retained secondary source	Electrolux measurement source — 103503878.pdf assets.skulytics.io	Page 7
Value used by ExactFit 1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Electrolux measurement source — 103503878.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-09 Exact-model installation-clearance table directly prints Back 1 in. Open original source ↗ Why this value was used Exact-model installation-clearance table directly prints Back 1 in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Wall clearance for door open to 90°	3 in	✓ Conflicting sources — resolved	Electrolux measurement source — 74492253.pdf assets.skulytics.io	Page 3
Value used by ExactFit 3 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Electrolux measurement source — 74492253.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-10-04 Top view: "Allow 3" min. clearance when opening the door at 90°". Replaces a calculated value. Open original source ↗ Why this value was used Top view: "Allow 3" min. clearance when opening the door at 90°". Replaces a calculated value. Other evidence found 5 in — superseded The same document as the value used above; page 2. Model scope: not separately recorded. Raw value: Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Exact-model sheet prints Width 36 in and Width With Doors 90 Degrees Open 46 in. Symmetric French-door per-side envelope is (46 - 36) / 2 = 5 in.. The final reviewed registry supersedes this earlier audit value. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Wall clearance for fully open door	14 in	? Verified — finalized database measurement	Electrolux measurement source — 74492253.pdf Publisher not recorded	Page 3
Value used by ExactFit 14 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Electrolux measurement source — 74492253.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-10-04 Top view: "Allow 14" min. clearance on the right and 11" min. clearance on the left when opening the door at 120°. Maximum door opening 120°." The larger clearance is stored (owner rule). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used Top view: "Allow 14" min. clearance on the right and 11" min. clearance on the left when opening the door at 120°. Maximum door opening 120°." The larger clearance is stored (owner rule). Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	35.875 in	✓ Verified — retained secondary source	Electrolux installation document — 74492253.pdf assets.skulytics.io	Page 2
Value used by ExactFit 35.875 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Electrolux installation document — 74492253.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Width of Cabinet 35 7/8" Open original source ↗ Why this value was used Width of Cabinet 35 7/8" Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Minimum cutout width

Selected: 36 in. Earlier retained values: 36.625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

"Built-In Look" Cutout Dimensions: (A) 70 3/8" (B) 36" (C) 25". Replaces a calculated value.

View source scope, location, and impact on fit

Minimum cutout height

Selected: 70.375 in. Earlier retained values: 70.575 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

"Built-In Look" Cutout Dimensions: (A) 70 3/8" (B) 36" (C) 25". Replaces a calculated value.

View source scope, location, and impact on fit

Minimum cutout depth

Selected: 25 in. Earlier retained values: 25.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

"Built-In Look" Cutout Dimensions: (A) 70 3/8" (B) 36" (C) 25". Replaces a calculated value.

View source scope, location, and impact on fit

Wall clearance for door open to 90°

Selected: 3 in. Earlier retained values: 5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Top view: "Allow 3" min. clearance when opening the door at 90°". Replaces a calculated value.

View source scope, location, and impact on fit

Source documents and pages

Electrolux installation document — 74492253.pdf

assets.skulytics.io · Installation manual · secondary model/source

Model numbers covered: ERMC2295AS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.

13 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Wall clearance for door open to 90°; Wall clearance for fully open door; Cabinet case width.

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Electrolux measurement source — 103503878.pdf

assets.skulytics.io · Web source · secondary model/source

Model numbers covered: ERMC2295AS. Publication/revision date: Not recorded. Reviewed: 2026-09-09.

4 displayed measurements supported: Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.

Availability: retained review record; original URL retained (current availability not rechecked).

Open original source ↗

Report a problem with this model Check whether ERMC2295AS fits your opening Back to Electrolux ERMC2295AS Read the full verification methodology

Evidence reflects the sources reviewed on 2026-10-04. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.

Evidence summary

Complete mixed evidence

Measurements and supporting evidence

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence

Why this value was used

Other evidence found

Effect on fit result

Value used by ExactFit

Primary evidence