This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Counter-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-17. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 36 in | ✓ Verified — retained secondary source | Electrolux installation document — 74536292.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceElectrolux installation document — 74536292.pdf Width 36"Open original source ↗ Why this value was usedWidth 36" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 68.3 in | ✓ Verified — retained secondary source | Electrolux installation document — 74536292.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit68.3 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceElectrolux installation document — 74536292.pdf Height Without Hinge 68 3/10"Open original source ↗ Why this value was usedHeight Without Hinge 68 3/10" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 70 in | ✓ Verified — retained secondary source | Electrolux installation document — 74536292.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit70 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceElectrolux installation document — 74536292.pdf Height With Hinge 70"Open original source ↗ Why this value was usedHeight With Hinge 70" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 23.6 in | ✓ Verified — retained secondary source | Electrolux installation document — 74536292.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit23.6 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceElectrolux installation document — 74536292.pdf Depth of Cabinet 23 6/10"Open original source ↗ Why this value was usedDepth of Cabinet 23 6/10" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 28.5 in | ✓ Verified — retained secondary source | Electrolux installation document — 74536292.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit28.5 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceElectrolux installation document — 74536292.pdf Depth With Door 28 1/2"Open original source ↗ Why this value was usedDepth With Door 28 1/2" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 30.8 in | ✓ Verified — retained secondary source | Electrolux installation document — 74536292.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit30.8 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceElectrolux installation document — 74536292.pdf Depth With Door and Handle 30 8/10"Open original source ↗ Why this value was usedDepth With Door and Handle 30 8/10" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 43.5 in | ✓ Verified — retained secondary source | Electrolux installation document — 74536292.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit43.5 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceElectrolux installation document — 74536292.pdf Depth With Door 90° Open 43 1/2"Open original source ↗ Why this value was usedDepth With Door 90° Open 43 1/2" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36.35 in | ✓ Conflicting sources — resolved · Calculated/inferred | Electrolux measurement source — 74536292.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit36.35 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: case_width_in + 2 * side_ventilation_clearance_in Confidence label: high. Calculation inputs: Left-side ventilation clearance; Cabinet case width; Primary evidenceElectrolux measurement source — 74536292.pdf Calculated opening width from exact-model cabinet width 35.6 in plus two exact-model side installation clearances of 0.375 in; clearance source 103505017.pdf, page 7.Open original source ↗ Why this value was usedCalculated opening width from exact-model cabinet width 35.6 in plus two exact-model side installation clearances of 0.375 in; clearance source 103505017.pdf, page 7. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 70.375 in | ✓ Verified — retained secondary source · Calculated/inferred | Electrolux measurement source — 74536292.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit70.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: height_hinge_in + top_clearance_in Confidence label: high. Calculation inputs: Height with hinge / controlling height; Top clearance; Primary evidenceElectrolux measurement source — 74536292.pdf Calculated opening height from exact-model hinge height 70 in plus exact-model top clearance 0.375 in; clearance source 103505017.pdf, page 7.Open original source ↗ Why this value was usedCalculated opening height from exact-model hinge height 70 in plus exact-model top clearance 0.375 in; clearance source 103505017.pdf, page 7. Calculation or inference: height_hinge_in + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 24.6 in | ✓ Verified — retained secondary source · Calculated/inferred | Electrolux measurement source — 74536292.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit24.6 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: high. Calculation inputs: Depth without door; Rear clearance; Primary evidenceElectrolux measurement source — 74536292.pdf Calculated opening depth from exact-model cabinet depth 23.6 in plus exact-model rear clearance 1 in; clearance source 103505017.pdf, page 7.Open original source ↗ Why this value was usedCalculated opening depth from exact-model cabinet depth 23.6 in plus exact-model rear clearance 1 in; clearance source 103505017.pdf, page 7. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.375 in | ✓ Verified — retained secondary source | Electrolux measurement source — 103505017.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceElectrolux measurement source — 103505017.pdf • | Sides & Top 3/8 inch (9.5 mm) | • | deterministic pattern: installation_sidesOpen original source ↗ Why this value was used• | Sides & Top 3/8 inch (9.5 mm) | • | deterministic pattern: installation_sides Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.375 in | ✓ Verified — retained secondary source | Electrolux measurement source — 103505017.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceElectrolux measurement source — 103505017.pdf • | Sides & Top 3/8 inch (9.5 mm) | • | deterministic pattern: installation_sidesOpen original source ↗ Why this value was used• | Sides & Top 3/8 inch (9.5 mm) | • | deterministic pattern: installation_sides Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.375 in | ✓ Verified — retained secondary source | Electrolux measurement source — 103505017.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceElectrolux measurement source — 103505017.pdf • | Sides & Top 3/8 inch (9.5 mm) | • | deterministic pattern: installation_sidesOpen original source ↗ Why this value was used• | Sides & Top 3/8 inch (9.5 mm) | • | deterministic pattern: installation_sides Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Verified — retained secondary source | Electrolux measurement source — 103505017.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceElectrolux measurement source — 103505017.pdf Exact-model installation-clearance table directly prints Back 1 in.Open original source ↗ Why this value was usedExact-model installation-clearance table directly prints Back 1 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 3.75 in | ✓ Verified — retained secondary source · Calculated/inferred | Electrolux measurement source — 74536292.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit3.75 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (width_with_doors_90_open - width_doors_closed_in) / 2 Confidence label: high. Calculation inputs: Overall width; Primary evidenceElectrolux measurement source — 74536292.pdf Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Exact-model sheet prints Width 36 in and Width With Doors 90 Degrees Open 43.5 in. Symmetric French-door per-side envelope is (43.5 - 36) / 2 = 3.75 in.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Exact-model sheet prints Width 36 in and Width With Doors 90 Degrees Open 43.5 in. Symmetric French-door per-side envelope is (43.5 - 36) / 2 = 3.75 in. Calculation or inference: (width_with_doors_90_open - width_doors_closed_in) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.6 in | ✓ Verified — retained secondary source | Electrolux installation document — 74536292.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit35.6 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceElectrolux installation document — 74536292.pdf Width of Cabinet 35 6/10"Open original source ↗ Why this value was usedWidth of Cabinet 35 6/10" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 36.35 in. Earlier retained values: 35.6 in, 35.6 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Calculated opening width from exact-model cabinet width 35.6 in plus two exact-model side installation clearances of 0.375 in; clearance source 103505017.pdf, page 7. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: ERFC2393AS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
12 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: ERFC2393AS. Publication/revision date: Not recorded. Reviewed: 2026-09-09.
4 displayed measurements supported: Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-17. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.