This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-09-05. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux EI33AR80WS Product Specifications Sheet assets.skulytics.io · Product Specifications Sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux EI33AR80WS Product Specifications Sheet assets.skulytics.io · Product Specifications Sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux EI33AR80WS Product Specifications Sheet assets.skulytics.io · Product Specifications Sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux measurement source — https://www.rona.ca/en/product/electrolux-33-in-189-ft3-1-door-freezerless-refrigerator-stainless-steel-ei33ar80ws-10355784 www.rona.ca · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Exact-model RONA specification: Depth (Less Door) 24.625 in. Reviewed: 2026-09-04
Exact-model RONA specification: Depth (Less Door) 24.625 in.
Exact-model RONA specification: Depth (Less Door) 24.625 in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux EI33AR80WS Product Specifications Sheet assets.skulytics.io · Product Specifications Sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux measurement source — https://www.rona.ca/en/product/electrolux-33-in-189-ft3-1-door-freezerless-refrigerator-stainless-steel-ei33ar80ws-10355784 www.rona.ca · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Exact-model RONA specification: Depth (Including Handles) 28.625 in. Reviewed: 2026-09-04
Exact-model RONA specification: Depth (Including Handles) 28.625 in.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux EI33AR80WS Product Specifications Sheet assets.skulytics.io · Product Specifications Sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux EI33AR80WS Complete Owner's Guide assets.skulytics.io · Complete Owner's Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-09-04
Manufacturer installation guide: Minimum Cabinet dimensions for Single Unit WITHOUT Trim Kit, width 33".
Manufacturer installation guide: Minimum Cabinet dimensions for Single Unit WITHOUT Trim Kit, width 33".
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Minimum opening height derived from highest stored appliance endpoint 72.5 in plus documented top clearance 1.0 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Minimum opening depth derived from case-only depth 24.625 in plus propagated rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.
Why evidence from GRDA1911AF applies
Target model: EI33AR80WS. Supporting model: GRDA1911AF. Manufacturer: Electrolux. Product family and measurement relationship: depth_case_only_in + rear_clearance_in.
Measurement transferred: Minimum cutout depth. Relevant equivalence evidence: Minimum opening depth derived from case-only depth 24.625 in plus propagated rear clearance 1.0 in.. Known differences: not separately recorded. Review decision: preserved documented inference; 2026-09-05.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux EI33AR80WS Complete Owner's Guide assets.skulytics.io · Complete Owner's Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-09-05
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux EI33AR80WS Complete Owner's Guide assets.skulytics.io · Complete Owner's Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-09-05
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
Electrolux EI33AR80WS Complete Owner's Guide assets.skulytics.io · Complete Owner's Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-09-05
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Frigidaire_Gallery GRDA1911AF
Confidence label: medium.
Primary evidence
Frigidaire Gallery GRDA1911AF Complete Owner's Guide assets.skulytics.io · Complete Owner's Guide Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 6 Reviewed: 2026-09-05
Conflict-free corporate-family exact 8-dimension chassis match to Frigidaire_Gallery GRDA1911AF; original evidence: • Sides 3/16" (4.76 mm) | • Back 1" (25.4 mm) | 3.4 Cabinet leveling and door
Conflict-free corporate-family exact 8-dimension chassis match to Frigidaire_Gallery GRDA1911AF; original evidence: • Sides 3/16" (4.76 mm) | • Back 1" (25.4 mm) | 3.4 Cabinet leveling and door Calculation or inference: exact 8-dimension chassis signature; source model Frigidaire_Gallery GRDA1911AF.
Why evidence from GRDA1911AF applies
Target model: EI33AR80WS. Supporting model: GRDA1911AF. Manufacturer: Electrolux. Product family and measurement relationship: exact 8-dimension chassis signature; source model Frigidaire_Gallery GRDA1911AF.
Measurement transferred: Rear clearance. Relevant equivalence evidence: Conflict-free corporate-family exact 8-dimension chassis match to Frigidaire_Gallery GRDA1911AF; original evidence: • Sides 3/16" (4.76 mm) | • Back 1" (25.4 mm) | 3.4 Cabinet leveling and door. Known differences: not separately recorded. Review decision: preserved documented inference; 2026-09-05.
This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence.
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux EI33AR80WS Complete Owner's Guide assets.skulytics.io · Complete Owner's Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-09-05
Manufacturer manual documents 0.1875 in side installation clearance. The hinge-wall note is conditional and gives no separate numeric minimum; the documented side baseline is retained.
Manufacturer manual documents 0.1875 in side installation clearance. The hinge-wall note is conditional and gives no separate numeric minimum; the documented side baseline is retained.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux EI33AR80WS Product Specifications Sheet assets.skulytics.io · Product Specifications Sheet Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Electrolux EI33AR80WS Complete Owner's Guide assets.skulytics.io · Complete Owner's Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-09-04
Model numbers covered: EI33AR80WS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
6 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth with door, without handles; Depth with doors open at 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.