Measurement evidence for Cafe CYE22TP4MW2

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe installation document — 105165793.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Dimension H: Width 35 3/4 in. Dimension G (43 3/8 in.) is depth with fresh-food door open 90 degrees.

Why this value was used

Dimension H: Width 35 3/4 in. Dimension G (43 3/8 in.) is depth with fresh-food door open 90 degrees.

Other evidence found

• 43.375 in — superseded

  Document 105165879.pdf; page 2. Model scope: not separately recorded. Raw value: Width (in.) H -> 43-3/8. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe installation document — 105165879.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Height to top of case (in.) C -> 69

Why this value was used

Height to top of case (in.) C -> 69

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe installation document — 105165879.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Height to top of hinge (in.) B -> 70-1/2

Why this value was used

Height to top of hinge (in.) B -> 70-1/2

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe installation document — 105165879.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Case depth without door (in.) D -> 24-3/8

Why this value was used

Case depth without door (in.) D -> 24-3/8

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

30.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe installation document — 105165879.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Case depth less door handle (in.) E -> 30-1/4

Why this value was used

Case depth less door handle (in.) E -> 30-1/4

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

31.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe installation document — 105165879.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Case depth with door handle (in.) F -> 31-1/4

Why this value was used

Case depth with door handle (in.) F -> 31-1/4

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

43.38 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe measurement source — CAFE-ENERGY-STAR-22-1-Cu-Ft-Smart-Counter-Depth-French-Door-Refrigerator-with-Hot-Water-Dispenser-CYE22TP4MW2
Cafe · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth Without Door 24.375 in Depth with Door Open 90°: 43.38 in | ® 22.1 Cu. Ft. Smart Counter-Depth
Reviewed: 2026-09-04

Depth Without Door 24.375 in Depth with Door Open 90°: 43.38 in | ® 22.1 Cu. Ft. Smart Counter-Depth French ... CYE22TP4MW2. Width 35.750 in Case Depth Without Door 24.375 in Depth with Door Open 90° 43.375 in Depth Without Handle 30.25. Weight 365 lb Overall Depth 31.25

Why this value was used

Depth Without Door 24.375 in Depth with Door Open 90°: 43.38 in | ® 22.1 Cu. Ft. Smart Counter-Depth French ... CYE22TP4MW2. Width 35.750 in Case Depth Without Door 24.375 in Depth with Door Open 90° 43.375 in Depth Without Handle 30.25. Weight 365 lb Overall Depth 31.25

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe measurement source — CYE22TP4MW2-105165880.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 34
Reviewed: 2026-09-10

Manufacturer installation instructions directly state that cabinet opening width W should not be less than 36 in.

Why this value was used

Manufacturer installation instructions directly state that cabinet opening width W should not be less than 36 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

71.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(69, 70.5) + 1

Confidence label: high.

Primary evidence

Cafe measurement source — CYE22TP4MW2-105165880.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 27
Reviewed: 2026-09-10

Highest exact appliance-height endpoint from the exact-model Quick Specs plus the directly printed 1 in top clearance from the shared manufacturer installation instructions.

Why this value was used

Highest exact appliance-height endpoint from the exact-model Quick Specs plus the directly printed 1 in top clearance from the shared manufacturer installation instructions. Calculation or inference: max(69, 70.5) + 1.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 24.375 + 2

Confidence label: high.

Primary evidence

Cafe measurement source — CYE22TP4MW2-105165880.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 27
Reviewed: 2026-09-10

Exact case depth without door from the exact-model Quick Specs plus the directly printed 2 in back clearance from the shared manufacturer installation instructions.

Why this value was used

Exact case depth without door from the exact-model Quick Specs plus the directly printed 2 in back clearance from the shared manufacturer installation instructions. Calculation or inference: 24.375 + 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe measurement source — Cafe exact-family installation manuals cached in Tavily advanced results
www.ajmadison.com · Web source
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Corrected prior value 13.125 in (Min distance between side of case and wall, in either direction, to
Reviewed: 2026-09-05

Corrected prior value 13.125 in (Min distance between side of case and wall, in either direction, to allow doors to open fully (in.) K -> 13-1/8). Exact-family installation instructions: opening W must not be less than 36 in; 1/8 in side air clearance. Replaces door-swing wall clearance.

Why this value was used

Corrected prior value 13.125 in (Min distance between side of case and wall, in either direction, to allow doors to open fully (in.) K -> 13-1/8). Exact-family installation instructions: opening W must not be less than 36 in; 1/8 in side air clearance. Replaces door-swing wall clearance.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe measurement source — Cafe exact-family installation manuals cached in Tavily advanced results
www.ajmadison.com · Web source
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Corrected prior value 13.125 in (Min distance between side of case and wall, in either direction, to
Reviewed: 2026-09-05

Corrected prior value 13.125 in (Min distance between side of case and wall, in either direction, to allow doors to open fully (in.) K -> 13-1/8). Exact-family installation instructions: opening W must not be less than 36 in; 1/8 in side air clearance. Replaces door-swing wall clearance.

Why this value was used

Corrected prior value 13.125 in (Min distance between side of case and wall, in either direction, to allow doors to open fully (in.) K -> 13-1/8). Exact-family installation instructions: opening W must not be less than 36 in; 1/8 in side air clearance. Replaces door-swing wall clearance.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe measurement source — CYE22TP4MW2-105165880.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 27
Reviewed: 2026-09-10

Manufacturer installation instructions CLEARANCES box directly prints Top = 1 in at the cabinet/hinge cover.

Why this value was used

Manufacturer installation instructions CLEARANCES box directly prints Top = 1 in at the cabinet/hinge cover.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe measurement source — CYE22TP4MW2-105165880.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 27
Reviewed: 2026-09-10

Manufacturer installation instructions CLEARANCES box directly prints Back = 2 in.

Why this value was used

Manufacturer installation instructions CLEARANCES box directly prints Back = 2 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

13.125 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Cafe measurement source — 105165879.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (fully open). Exact-model Cafe dimension table: minimum distance between side of case and wall, in either direction, to allow doors to open fully = 13 1/8".

Why this value was used

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (fully open). Exact-model Cafe dimension table: minimum distance between side of case and wall, in either direction, to allow doors to open fully = 13 1/8".

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe measurement source — CYE22TP4MW2-105165879.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Exact-model dimension drawing labels H as Width = 35 3/4 in; the H arrow visibly spans the refrigerator case body rather than the open doors.

Why this value was used

Exact-model dimension drawing labels H as Width = 35 3/4 in; the H arrow visibly spans the refrigerator case body rather than the open doors.

Other evidence found

• 43.375 in — superseded

  Document 105165879.pdf; page 2. Model scope: not separately recorded. Raw value: Width (in.) H -> 43-3/8. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.