This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Counter-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-17. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 32.75 in | ✓ Verified — retained secondary source | Cafe installation document — 104283054.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit32.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 104283054.pdf Overall Width 32-3/4 inOpen original source ↗ Why this value was usedOverall Width 32-3/4 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 68.625 in | ✓ Verified — retained secondary source | Cafe installation document — 104283054.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit68.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 104283054.pdf Height to Top of Case 68-5/8 inOpen original source ↗ Why this value was usedHeight to Top of Case 68-5/8 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.75 in | ✓ Conflicting sources — resolved | Cafe installation document — 104283054.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit69.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 104283054.pdf Visual/native table repair: replaced legacy misassociated value 69.875 with labeled GE table value 69.75.Open original source ↗ Why this value was usedVisual/native table repair: replaced legacy misassociated value 69.875 with labeled GE table value 69.75. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24.125 in | ✓ Verified — retained secondary source | Cafe installation document — 104283054.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit24.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 104283054.pdf Case Depth Without Door 24-1/8 inOpen original source ↗ Why this value was usedCase Depth Without Door 24-1/8 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 29 in | ✓ Verified — retained secondary source | Cafe installation document — 104283054.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit29 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 104283054.pdf Case depth less door handle (in.) E -> 29Open original source ↗ Why this value was usedCase depth less door handle (in.) E -> 29 Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 31 in | ✓ Conflicting sources — resolved | Cafe installation document — 104283054.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit31 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 104283054.pdf Visual/native table repair: replaced legacy misassociated value 29.0 with labeled GE table value 31.0.Open original source ↗ Why this value was usedVisual/native table repair: replaced legacy misassociated value 29.0 with labeled GE table value 31.0. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 42 in | ✓ Verified — retained secondary source | Cafe installation document — 104283054.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit42 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 104283054.pdf Depth with Door Open 90° = 42 in.Open original source ↗ Why this value was usedDepth with Door Open 90° = 42 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 33 in | ✓ Verified — retained secondary source · Calculated/inferred | Cafe measurement source — CWE19SP3ND1_104283054.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit33 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 32.75 + 2 * 0.125 Confidence label: high. Primary evidenceCafe measurement source — CWE19SP3ND1_104283054.pdf Exact 32 3/4 in width plus the directly printed 1/8 in air clearance on each side.Open original source ↗ All retained supporting links
Why this value was usedExact 32 3/4 in width plus the directly printed 1/8 in air clearance on each side. Calculation or inference: 32.75 + 2 * 0.125. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 70.75 in | ✓ Verified — retained secondary source · Calculated/inferred | Cafe measurement source — CWE19SP3ND1_104283054.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit70.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(68.625, 69.75) + 1 Confidence label: high. Primary evidenceCafe measurement source — CWE19SP3ND1_104283054.pdf Exact 69 3/4 in hinge height plus the directly printed 1 in top air clearance.Open original source ↗ All retained supporting links
Why this value was usedExact 69 3/4 in hinge height plus the directly printed 1 in top air clearance. Calculation or inference: max(68.625, 69.75) + 1. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 26.125 in | ✓ Verified — retained secondary source · Calculated/inferred | Cafe measurement source — CWE19SP3ND1_104283054.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit26.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24.125 + 2 Confidence label: high. Primary evidenceCafe measurement source — CWE19SP3ND1_104283054.pdf Exact 24 1/8 in case depth without door plus the directly printed 2 in back air clearance.Open original source ↗ Why this value was usedExact 24 1/8 in case depth without door plus the directly printed 2 in back air clearance. Calculation or inference: 24.125 + 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Cafe measurement source — CWE19SP3ND1_104283054.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CWE19SP3ND1_104283054.pdf Café family Quick Specs AIR CLEARANCES table directly prints Each side = 1/8 in.Open original source ↗ All retained supporting links
Why this value was usedCafé family Quick Specs AIR CLEARANCES table directly prints Each side = 1/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Cafe measurement source — CWE19SP3ND1_104283054.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CWE19SP3ND1_104283054.pdf Café family Quick Specs AIR CLEARANCES table directly prints Each side = 1/8 in.Open original source ↗ All retained supporting links
Why this value was usedCafé family Quick Specs AIR CLEARANCES table directly prints Each side = 1/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 1 in | ✓ Verified — retained secondary source | Cafe measurement source — CWE19SP3ND1_104283054.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CWE19SP3ND1_104283054.pdf Café family Quick Specs AIR CLEARANCES table directly prints Top = 1 in.Open original source ↗ All retained supporting links
Why this value was usedCafé family Quick Specs AIR CLEARANCES table directly prints Top = 1 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Verified — retained secondary source | Cafe measurement source — CWE19SP3ND1_104283054.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CWE19SP3ND1_104283054.pdf Café family Quick Specs AIR CLEARANCES table directly prints Back = 2 in.Open original source ↗ All retained supporting links
Why this value was usedCafé family Quick Specs AIR CLEARANCES table directly prints Back = 2 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 3.875 in | ✓ Verified — retained secondary source · Calculated/inferred | Cafe measurement source — CWE19SP3ND1_104283054.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit3.875 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (40.5 - 32.75) / 2 Confidence label: high. Primary evidenceCafe measurement source — CWE19SP3ND1_104283054.pdf Migrated from hinge_side_wall_clearance_in (90 degrees). Exact 40 1/2 in width with doors open 90 degrees minus 32 3/4 in closed width, divided equally between the two symmetric French doors.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in (90 degrees). Exact 40 1/2 in width with doors open 90 degrees minus 32 3/4 in closed width, divided equally between the two symmetric French doors. Calculation or inference: (40.5 - 32.75) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 32.75 in | ✓ Verified — retained secondary source | Cafe installation document — 104283054.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit32.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 104283054.pdf Overall Width 32-3/4 inOpen original source ↗ Why this value was usedOverall Width 32-3/4 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 69.75 in. Earlier retained values: 69.875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Visual/native table repair: replaced legacy misassociated value 69.875 with labeled GE table value 69.75.
View source scope, location, and impact on fitSelected: 31 in. Earlier retained values: 29 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Visual/native table repair: replaced legacy misassociated value 29.0 with labeled GE table value 31.0.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: CWE19SP3ND1. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
8 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: CWE19SP3ND1. Publication/revision date: Not recorded. Reviewed: 2026-09-17.
8 displayed measurements supported: Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-17. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.