Measurement evidence for Cafe CWE19SP2NS1

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to Cafe CWE19SP2NS1 fit check Check this model against your opening How ExactFit verifies measurements

Cafe CWE19SP2NS1

Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Incomplete evidence

0exact-model manufacturer values

1verified equivalent/same-chassis values

11secondary-source-only values

4values with unresolved source details

Last reviewed: 2026-09-05. 5 retained source records. 0 unresolved conflicts. Not every fit-critical input is supported.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.

ExactFit does not have sufficient evidence for every fit-critical measurement. The fit checker will return Uncertain unless a known measurement already proves that the model does not fit.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	32.75 in	✓ Secondary source only	Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 32.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Overall Width 32-3/4 in Open original source ↗ Why this value was used Overall Width 32-3/4 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	68.625 in	✓ Secondary source only	Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 68.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Height to Top of Case 68-5/8 in Open original source ↗ Why this value was used Height to Top of Case 68-5/8 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	69.75 in	✓ Conflicting sources — resolved	Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io	Page 2
Value used by ExactFit 69.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Visual/native table repair: replaced legacy misassociated value 69.875 with labeled GE table value 69.75. Open original source ↗ Why this value was used Visual/native table repair: replaced legacy misassociated value 69.875 with labeled GE table value 69.75. Other evidence found 69.875 in — superseded 104283093.pdf; page 1. Model scope: not separately recorded. Raw value: Overall Height 69-7/8 in. The final reviewed registry supersedes this earlier audit value. Visual/native table repair: replaced legacy misassociated value 69.875 with labeled GE table value 69.75. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	24.125 in	✓ Secondary source only	Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 24.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Case Depth Without Door 24-1/8 in Open original source ↗ Why this value was used Case Depth Without Door 24-1/8 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	29 in	✓ Secondary source only	Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io	Page 2
Value used by ExactFit 29 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Case depth less door handle (in.) E -> 29 Open original source ↗ Why this value was used Case depth less door handle (in.) E -> 29 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	31 in	✓ Conflicting sources — resolved	Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io	Page 2
Value used by ExactFit 31 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Visual/native table repair: replaced legacy misassociated value 29.0 with labeled GE table value 31.0. Open original source ↗ Why this value was used Visual/native table repair: replaced legacy misassociated value 29.0 with labeled GE table value 31.0. Other evidence found 29 in — superseded 104283093.pdf; page 1. Model scope: not separately recorded. Raw value: Depth With Handle = 29 in.. The final reviewed registry supersedes this earlier audit value. Visual/native table repair: replaced legacy misassociated value 29.0 with labeled GE table value 31.0. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	42 in	✓ Secondary source only	Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 42 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Depth with Door Open 90° = 42 in. Open original source ↗ Why this value was used Depth with Door Open 90° = 42 in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	33 in	✓ Secondary source only · Calculated/inferred	Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io	Page 2
Value used by ExactFit 33 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 32.75 + 2 * 0.125 Confidence label: medium. Primary evidence Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Minimum opening derived from exact product width plus explicit symmetric side spacing: 32.75 + 2 * 0.125 = 33.0 in. Side evidence: Visually confirmed GE ordered dimensions/air-clearances table. GE ordered dimension table values: 69-7/8 \| 69-3/4 \| 68-5/8 \| 24-1/8 \| 29 \| 31 \| 42 \| 32-3/4 \| 40-1/2 \| 1/8 \| 1 \| 2 Open original source ↗ Why this value was used Minimum opening derived from exact product width plus explicit symmetric side spacing: 32.75 + 2 * 0.125 = 33.0 in. Side evidence: Visually confirmed GE ordered dimensions/air-clearances table. GE ordered dimension table values: 69-7/8 \| 69-3/4 \| 68-5/8 \| 24-1/8 \| 29 \| 31 \| 42 \| 32-3/4 \| 40-1/2 \| 1/8 \| 1 \| 2 Calculation or inference: 32.75 + 2 * 0.125. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	Unknown	? Not found · Calculated/inferred	GYE18JYLFS (Refrigerators - French 3-Door) - B & J Appliance - Enid, OK www.bandjappliance.com	Retained specification excerpt: Minimum opening height derived from highest appliance endpoint 69.75 in plus propagated top clearanc
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidence GYE18JYLFS (Refrigerators - French 3-Door) - B & J Appliance - Enid, OK www.bandjappliance.com · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Minimum opening height derived from highest appliance endpoint 69.75 in plus propagated top clearanc Reviewed: 2026-09-05 Minimum opening height derived from highest appliance endpoint 69.75 in plus propagated top clearance 1.0 in. Open original source ↗ Why this value was used A required calculation input lacks defensible evidence. Retained research value: 70.75 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	Unknown	? Not found · Calculated/inferred	CAFÉ™ ENERGY STAR® 18.6 Cu. Ft. Counter-Depth French-Door ... www.appliancealliance.com	Retained specification excerpt: Minimum opening depth derived from case-only depth 24.125 in plus propagated rear clearance 2.0 in.
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidence CAFÉ™ ENERGY STAR® 18.6 Cu. Ft. Counter-Depth French-Door ... www.appliancealliance.com · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Minimum opening depth derived from case-only depth 24.125 in plus propagated rear clearance 2.0 in. Reviewed: 2026-09-05 Minimum opening depth derived from case-only depth 24.125 in plus propagated rear clearance 2.0 in. Open original source ↗ Why this value was used A required calculation input lacks defensible evidence. Retained research value: 26.125 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	0.125 in	✓ Verified — equivalent model · Calculated/inferred	GE GWE19JGLBB Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared 32.75-inch GWE19/CWE19 chassis Confidence label: medium. Primary evidence GE GWE19JGLBB Quick Specs assets.skulytics.io · Quick Specs Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Exact shared GE/Cafe 32.75-inch chassis specification: side air clearance = 1/8". Open original source ↗ Why this value was used Exact shared GE/Cafe 32.75-inch chassis specification: side air clearance = 1/8". Calculation or inference: shared 32.75-inch GWE19/CWE19 chassis. Why evidence from GWE19JGLBB applies Target model: CWE19SP2NS1. Supporting model: GWE19JGLBB. Manufacturer: Cafe. Product family and measurement relationship: shared 32.75-inch GWE19/CWE19 chassis. Measurement transferred: Left-side ventilation clearance. Relevant equivalence evidence: Exact shared GE/Cafe 32.75-inch chassis specification: side air clearance = 1/8".. Known differences: not separately recorded. Review decision: documented exact chassis clearance propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	0.125 in	✓ Verified — equivalent model · Calculated/inferred	GE GWE19JGLBB Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: shared 32.75-inch GWE19/CWE19 chassis Confidence label: medium. Primary evidence GE GWE19JGLBB Quick Specs assets.skulytics.io · Quick Specs Model scope: Equivalent model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Exact shared GE/Cafe 32.75-inch chassis specification: side air clearance = 1/8". Open original source ↗ Why this value was used Exact shared GE/Cafe 32.75-inch chassis specification: side air clearance = 1/8". Calculation or inference: shared 32.75-inch GWE19/CWE19 chassis. Why evidence from GWE19JGLBB applies Target model: CWE19SP2NS1. Supporting model: GWE19JGLBB. Manufacturer: Cafe. Product family and measurement relationship: shared 32.75-inch GWE19/CWE19 chassis. Measurement transferred: Right-side ventilation clearance. Relevant equivalence evidence: Exact shared GE/Cafe 32.75-inch chassis specification: side air clearance = 1/8".. Known differences: not separately recorded. Review decision: documented exact chassis clearance propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	Unknown	? Not found · Calculated/inferred	GYE18JYLFS (Refrigerators - French 3-Door) - B & J Appliance - Enid, OK www.bandjappliance.com	Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to GE GYE18JYLFS; original evidence:
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model GE GYE18JYLFS Confidence label: medium. Primary evidence GYE18JYLFS (Refrigerators - French 3-Door) - B & J Appliance - Enid, OK www.bandjappliance.com · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to GE GYE18JYLFS; original evidence: Reviewed: 2026-09-05 Conflict-free corporate-family exact 8-dimension chassis match to GE GYE18JYLFS; original evidence: Exact-model cached page explicitly labels top_clearance_in=1 in; 1 cached copy/copies; no contrary parsed value. Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 1 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	Unknown	? Not found · Calculated/inferred	CAFÉ™ ENERGY STAR® 18.6 Cu. Ft. Counter-Depth French-Door ... www.appliancealliance.com	Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Cafe CWE19SP3ND1; original evidenc
Value used by ExactFit Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Cafe CWE19SP3ND1 Confidence label: medium. Primary evidence CAFÉ™ ENERGY STAR® 18.6 Cu. Ft. Counter-Depth French-Door ... www.appliancealliance.com · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Cafe CWE19SP3ND1; original evidenc Reviewed: 2026-09-05 Conflict-free corporate-family exact 8-dimension chassis match to Cafe CWE19SP3ND1; original evidence: Exact-model cached page explicitly labels rear_clearance_in=2 in; 1 cached copy/copies; no contrary parsed value. Open original source ↗ Why this value was used The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning. Retained research value: 2 in. It is preserved for audit but not accepted as a safe fit input. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Hinge-side wall clearance	3.875 in	✓ Secondary source only · Calculated/inferred	Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 3.875 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (40.5 - 32.75) / 2 Confidence label: medium. Primary evidence Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Exact-model width-open table: 40 1/2" open width minus 32 3/4" closed width, divided between two doors = 3 7/8" per side. Open original source ↗ Why this value was used Exact-model width-open table: 40 1/2" open width minus 32 3/4" closed width, divided between two doors = 3 7/8" per side. Calculation or inference: (40.5 - 32.75) / 2. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	32.75 in	✓ Secondary source only	Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io	Page 1
Value used by ExactFit 32.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Overall Width 32-3/4 in Open original source ↗ Why this value was used Overall Width 32-3/4 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Adjoining-wall clearance (reviewed endpoint)	0.125 in	✓ Secondary source only	Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io	Page 2
Value used by ExactFit 0.125 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe CWE19SP2NS1 Quick Specs assets.skulytics.io · Quick Specs Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Visually confirmed GE ordered dimensions/air-clearances table. GE ordered dimension table values: 69-7/8 \| 69-3/4 \| 68-5/8 \| 24-1/8 \| 29 \| 31 \| 42 \| 32-3/4 \| 40-1/2 \| 1/8 \| 1 \| 2 Open original source ↗ Why this value was used Visually confirmed GE ordered dimensions/air-clearances table. GE ordered dimension table values: 69-7/8 \| 69-3/4 \| 68-5/8 \| 24-1/8 \| 29 \| 31 \| 42 \| 32-3/4 \| 40-1/2 \| 1/8 \| 1 \| 2 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Height with hinge / controlling height

Selected: 69.75 in. Earlier retained values: 69.875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Visual/native table repair: replaced legacy misassociated value 69.875 with labeled GE table value 69.75.

View source scope, location, and impact on fit

Depth with handle

Selected: 31 in. Earlier retained values: 29 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Visual/native table repair: replaced legacy misassociated value 29.0 with labeled GE table value 31.0.

View source scope, location, and impact on fit

Measurements not established

Minimum cutout height

Not found for safe fit use. Sources retained: https://www.bandjappliance.com/en/product/702321-ge-gye18jylfs. Related-model record: CWE19SP2NS1.

A required calculation input lacks defensible evidence.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Minimum cutout depth

Not found for safe fit use. Sources retained: https://www.appliancealliance.com/Cafe-CWE19SP3ND1-CAF-ENERGY-STAR-18-6-Cu-Ft-Counter-Depth-French-Door-Refrigerator. Related-model record: CWE19SP2NS1.

A required calculation input lacks defensible evidence.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Top clearance

Not found for safe fit use. Sources retained: https://www.bandjappliance.com/en/product/702321-ge-gye18jylfs. Related-model record: CWE19SP2NS1.

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Rear clearance

Not found for safe fit use. Sources retained: https://www.appliancealliance.com/Cafe-CWE19SP3ND1-CAF-ENERGY-STAR-18-6-Cu-Ft-Counter-Depth-French-Door-Refrigerator. Related-model record: CWE19SP2NS1.

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.

Source documents and pages

Cafe CWE19SP2NS1 Quick Specs

assets.skulytics.io · Quick Specs · secondary model/source

Model numbers covered: CWE19SP2NS1. Publication/revision date: Not recorded. Reviewed: 2026-09-04.

10 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Hinge-side wall clearance; Cabinet case width; Adjoining-wall clearance (reviewed endpoint).