This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Side-by-Side · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-29. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from; estimated values are not printed for this model and come from similar models of the same brand.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 48 in | ✓ Verified — retained secondary source | Cafe installation document — 105165422.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit48 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 105165422.pdf Overall Width 48 inOpen original source ↗ Why this value was usedOverall Width 48 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 83.5 in | ✓ Verified — retained secondary source | Cafe installation document — 105165422.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit83.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 105165422.pdf Height to Top of Case 83-1/2 inOpen original source ↗ Why this value was usedHeight to Top of Case 83-1/2 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 84 in | ✓ Verified — retained secondary source | Cafe installation document — 105165422.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 105165422.pdf Overall Height 84 inOpen original source ↗ Why this value was usedOverall Height 84 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 23.875 in | ✓ Verified — retained secondary source | Cafe installation document — 105165422.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit23.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 105165422.pdf Case Depth Without Door 23-7/8 inOpen original source ↗ Why this value was usedCase Depth Without Door 23-7/8 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 25.75 in | ✓ Verified — retained secondary source | Cafe installation document — 105165422.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit25.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 105165422.pdf Depth Without Handle 25-3/4 inOpen original source ↗ Why this value was usedDepth Without Handle 25-3/4 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 28.5 in | ✓ Conflicting sources — resolved | Cafe measurement source — CAFE-48-Smart-Built-In-Side-by-Side-Refrigerator-CSB48WP2NS1 Cafe | Retained specification excerpt: Official exact-model page: Overall Depth with Handle 28.5 in. | |
Value used by ExactFit28.5 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CAFE-48-Smart-Built-In-Side-by-Side-Refrigerator-CSB48WP2NS1 Official exact-model page: Overall Depth with Handle 28.5 in.Open original source ↗ Why this value was usedOfficial exact-model page: Overall Depth with Handle 28.5 in. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 52.5 in | ✓ Verified — retained secondary source | Cafe installation document — 105165422.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit52.5 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 105165422.pdf Depth with Fresh Food Door Open 90° = 52-1/2 in.Open original source ↗ Why this value was usedDepth with Fresh Food Door Open 90° = 52-1/2 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 47.5 in | ✓ Verified — retained secondary source | Cafe measurement source — CSB48WP2NS1-105165424.pdf assets.skulytics.io | Page 25 | |
Value used by ExactFit47.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CSB48WP2NS1-105165424.pdf Finished cutout width must be 47-1/2" for 48" models.Open original source ↗ Why this value was usedFinished cutout width must be 47-1/2" for 48" models. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 83.5 in | ✓ Conflicting sources — resolved | Cafe measurement source — 105165422.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit83.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — 105165422.pdf The front view prints the opening height as 84 +/- 1/2", so the minimum finished opening is 83-1/2 in (owner decision 2026-09-17 for the identical CSB48YP2NS1).Open original source ↗ Why this value was usedThe front view prints the opening height as 84 +/- 1/2", so the minimum finished opening is 83-1/2 in (owner decision 2026-09-17 for the identical CSB48YP2NS1). Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 24 in | ✓ Verified — retained secondary source | Cafe measurement source — 105165422.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — 105165422.pdf located as shown. | THE CUTOUT DEPTH MUST BE 24" | The refrigerator will project forward, slightly beyond adjacentOpen original source ↗ Why this value was usedlocated as shown. | THE CUTOUT DEPTH MUST BE 24" | The refrigerator will project forward, slightly beyond adjacent Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ≈ Estimated — not printed for this model | ExactFit estimate (Cafe doesn't print this for the model) ExactFit | Not printed for this model | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model. Original published value and unit: see retained transcription below. Normalization: typical Café side gap (estimate) Confidence label: low. Primary evidenceExactFit estimate (Cafe doesn't print this for the model) Not printed in the Café documents we have for this model. 1/8 in is the side gap Café prints for similar models (CAE28DM5TS5, CVE28DM5NS5, CGE29DM5TS5), so it is shown as an estimate. The fit check uses Café's cutout width for this model, so this estimate does not change the fit answer. No document we have for this model prints this value. Why this value was usedNot printed in the Café documents we have for this model. 1/8 in is the side gap Café prints for similar models (CAE28DM5TS5, CVE28DM5NS5, CGE29DM5TS5), so it is shown as an estimate. The fit check uses Café's cutout width for this model, so this estimate does not change the fit answer. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ≈ Estimated — not printed for this model | ExactFit estimate (Cafe doesn't print this for the model) ExactFit | Not printed for this model | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model. Original published value and unit: see retained transcription below. Normalization: typical Café side gap (estimate) Confidence label: low. Primary evidenceExactFit estimate (Cafe doesn't print this for the model) Not printed in the Café documents we have for this model. 1/8 in is the side gap Café prints for similar models (CAE28DM5TS5, CVE28DM5NS5, CGE29DM5TS5), so it is shown as an estimate. The fit check uses Café's cutout width for this model, so this estimate does not change the fit answer. No document we have for this model prints this value. Why this value was usedNot printed in the Café documents we have for this model. 1/8 in is the side gap Café prints for similar models (CAE28DM5TS5, CVE28DM5NS5, CGE29DM5TS5), so it is shown as an estimate. The fit check uses Café's cutout width for this model, so this estimate does not change the fit answer. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.125 in | ✓ Verified — retained secondary source · Calculated/inferred | Cafe measurement source — CSB48WP2NS1-105165422.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24 - 23.875 Confidence label: high. Primary evidenceCafe measurement source — CSB48WP2NS1-105165422.pdf Exact 24 in cutout depth on page 3 minus exact 23.875 in case depth without door on page 1.Open original source ↗ Why this value was usedExact 24 in cutout depth on page 3 minus exact 23.875 in case depth without door on page 1. Calculation or inference: 24 - 23.875. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 4.625 in | ? Verified — finalized database measurement | Cafe measurement source — 105165422.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit4.625 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidenceCafe measurement source — 105165422.pdf Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees (text also gives a fully open figure)). Exact CSB48 product-clearance table: 4 5/8" minimum at the 90-degree stop; full 130-degree clearances are 13 13/16" freezer / 18 15/16" fresh-food.Open original source ↗ All retained supporting links
Why this value was usedMigrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees (text also gives a fully open figure)). Exact CSB48 product-clearance table: 4 5/8" minimum at the 90-degree stop; full 130-degree clearances are 13 13/16" freezer / 18 15/16" fresh-food. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | 18.9375 in | ? Verified — finalized database measurement | Cafe measurement source — 105165422.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit18.9375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — 105165422.pdf Fresh-food door at full 130 degree swing: 18-15/16 in; the freezer door needs 13-13/16 in. The larger is stored so either door can open fully. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedFresh-food door at full 130 degree swing: 18-15/16 in; the freezer door needs 13-13/16 in. The larger is stored so either door can open fully. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 47 in | ✓ Conflicting sources — resolved | Cafe measurement source — CSB48WP2NS1-105165424.pdf assets.skulytics.io | Page 25 | |
Value used by ExactFit47 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CSB48WP2NS1-105165424.pdf Exact installation drawing: 47" Case Width; 48" is Frame to Frame.Open original source ↗ Why this value was usedExact installation drawing: 47" Case Width; 48" is Frame to Frame. Other evidence found
Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 28.5 in. Earlier retained values: 25.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Official exact-model page: Overall Depth with Handle 28.5 in.
View source scope, location, and impact on fitSelected: 83.5 in. Earlier retained values: 84.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
The front view prints the opening height as 84 +/- 1/2", so the minimum finished opening is 83-1/2 in (owner decision 2026-09-17 for the identical CSB48YP2NS1).
View source scope, location, and impact on fitSelected: 47 in. Earlier retained values: 48 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact installation drawing: 47" Case Width; 48" is Frame to Frame.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-09-24.
10 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with doors open at 90°; Minimum cutout height; Minimum cutout depth; Wall clearance for door open to 90°; Wall clearance for fully open door.
Availability: retained review record; original URL unavailable in the record.
Cafe · Web source · exact model/source
Model numbers covered: CSB48WP2NS1. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Depth with handle.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: CSB48WP2NS1. Publication/revision date: Not recorded. Reviewed: 2026-09-07.
2 displayed measurements supported: Minimum cutout width; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: CSB48WP2NS1. Publication/revision date: Not recorded. Reviewed: 2026-09-10.
1 displayed measurements supported: Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-29. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.