Measurement evidence for Cafe CIP36NP2VS1

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe installation document — 104369800.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall Width 35-3/4 in

Why this value was used

Overall Width 35-3/4 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.6875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe installation document — 104369800.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Visual table: B - Height to Top of Case = 83 11/16 in.

Why this value was used

Visual table: B - Height to Top of Case = 83 11/16 in.

Other evidence found

• 83.5 in — superseded

  Document 104369800.pdf; page 1. Model scope: not separately recorded. Raw value: Height to Top of Case 83-11/16 in. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe installation document — 104369800.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Visual table: A - Overall Height = 83 1/2 in.

Why this value was used

Visual table: A - Overall Height = 83 1/2 in.

Other evidence found

• 83.6875 in — superseded

  Document 104369800.pdf; page 1. Model scope: not separately recorded. Raw value: Overall Height 83-1/2 in. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

22.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe installation document — 104369800.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Case Depth Without Door 22-1/8 in

Why this value was used

Case Depth Without Door 22-1/8 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe installation document — 104369800.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth Without Handle 24-3/4 in

Why this value was used

Depth Without Handle 24-3/4 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

27.31 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe measurement source — CAFE-36-Integrated-French-Door-Refrigerator-CIP36NP2VS1
Cafe · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Reviewed cached exact-model manufacturer label: Depth with Handle = 27.31 in. Context: dle | 24.75 i
Reviewed: 2026-09-04

Reviewed cached exact-model manufacturer label: Depth with Handle = 27.31 in. Context: dle | 24.75 in | | Net Weight | 562 lb | | Overall Depth | 24.75 in | | Overall Depth with Handle | 27.3125 in | | Overall Height | 83.5 in | | Overall Width | 35.75 in | ## Reviews and Q&A

Why this value was used

Reviewed cached exact-model manufacturer label: Depth with Handle = 27.31 in. Context: dle | 24.75 in | | Net Weight | 562 lb | | Overall Depth | 24.75 in | | Overall Depth with Handle | 27.3125 in | | Overall Height | 83.5 in | | Overall Width | 35.75 in | ## Reviews and Q&A

Other evidence found

• 24.75 in — superseded

  Document 104369800.pdf; page 1. Model scope: not separately recorded. Raw value: Overall Depth 24-3/4 in. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

46.375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe measurement source — CIP36NP2VS1_104369800.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Cafe dimensional drawing visually prints total side-view depth with the refrigerator door open 90 degrees as 46 3/8 in.

Why this value was used

Exact-model Cafe dimensional drawing visually prints total side-view depth with the refrigerator door open 90 degrees as 46 3/8 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe measurement source — CIP36NP2VS1_104369800.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-10

Exact-model Café fully integrated installation drawing directly dimensions the 36 in finished opening width.

Why this value was used

Exact-model Café fully integrated installation drawing directly dimensions the 36 in finished opening width.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

84 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe measurement source — CIP36NP2VS1_104369800.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-10

Exact-model Café fully integrated installation drawing directly dimensions the 84 in finished opening height.

Why this value was used

Exact-model Café fully integrated installation drawing directly dimensions the 84 in finished opening height.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe measurement source — CIP36NP2VS1_104369803.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 19
Reviewed: 2026-09-10

Exact-model Café design guide states: The Cutout Depth Must Be 25 in.

Why this value was used

Exact-model Café design guide states: The Cutout Depth Must Be 25 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model.

Original published value and unit: see retained transcription below. Normalization: typical Café side gap (estimate)

Confidence label: low.

Primary evidence

ExactFit estimate (Cafe doesn't print this for the model)
ExactFit · Estimate
Model scope: Estimate from similar models
Publication/revision date: Not recorded
Location: Not printed for this model
Reviewed: 2026-10-29

Not printed in the Café documents we have for this model. 1/8 in is the side gap Café prints for similar models (CAE28DM5TS5, CVE28DM5NS5, CGE29DM5TS5), so it is shown as an estimate. The fit check uses Café's cutout width for this model, so this estimate does not change the fit answer.

No document we have for this model prints this value.

Why this value was used

Not printed in the Café documents we have for this model. 1/8 in is the side gap Café prints for similar models (CAE28DM5TS5, CVE28DM5NS5, CGE29DM5TS5), so it is shown as an estimate. The fit check uses Café's cutout width for this model, so this estimate does not change the fit answer.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model.

Original published value and unit: see retained transcription below. Normalization: typical Café side gap (estimate)

Confidence label: low.

Primary evidence

ExactFit estimate (Cafe doesn't print this for the model)
ExactFit · Estimate
Model scope: Estimate from similar models
Publication/revision date: Not recorded
Location: Not printed for this model
Reviewed: 2026-10-29

Not printed in the Café documents we have for this model. 1/8 in is the side gap Café prints for similar models (CAE28DM5TS5, CVE28DM5NS5, CGE29DM5TS5), so it is shown as an estimate. The fit check uses Café's cutout width for this model, so this estimate does not change the fit answer.

No document we have for this model prints this value.

Why this value was used

Not printed in the Café documents we have for this model. 1/8 in is the side gap Café prints for similar models (CAE28DM5TS5, CVE28DM5NS5, CGE29DM5TS5), so it is shown as an estimate. The fit check uses Café's cutout width for this model, so this estimate does not change the fit answer.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.3125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 84 - 83.6875

Confidence label: high.

Primary evidence

Cafe measurement source — CIP36NP2VS1_104369800.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-10

Exact 84 in finished opening height on page 3 minus exact 83 11/16 in height to top of case on page 2 = 5/16 in top opening residual.

Why this value was used

Exact 84 in finished opening height on page 3 minus exact 83 11/16 in height to top of case on page 2 = 5/16 in top opening residual. Calculation or inference: 84 - 83.6875.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 25 - 22.125

Confidence label: high.

Primary evidence

Cafe measurement source — CIP36NP2VS1_104369800.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-10

Exact 25 in finished opening depth on page 3 minus exact 22 1/8 in case depth without door on page 1 = 2 7/8 in rear opening residual.

Why this value was used

Exact 25 in finished opening depth on page 3 minus exact 22 1/8 in case depth without door on page 1 = 2 7/8 in rear opening residual. Calculation or inference: 25 - 22.125.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

6.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Cafe measurement source — 104369800.pdf
assets.skulytics.io · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees (text also gives a fully open figure)). Exact CIP36 product-clearance table: Dim A is 6 3/4" at 90 degrees and 14" at the factory 115-degree stop.

Why this value was used

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees (text also gives a fully open figure)). Exact CIP36 product-clearance table: Dim A is 6 3/4" at 90 degrees and 14" at the factory 115-degree stop.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe installation document — 104369800.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall Width 35-3/4 in

Why this value was used

Overall Width 35-3/4 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.