Measurement evidence for Cafe CIC36RP2VS1

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to Cafe CIC36RP2VS1 fit check Check this model against your opening How ExactFit verifies measurements

Cafe CIC36RP2VS1

Bottom Freezer · Built-in
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Complete mixed evidence

3exact-model manufacturer values

0verified equivalent/same-chassis values

10secondary-source-only values

1estimated values (not printed for this model)

2values with unresolved source details

Last reviewed: 2026-10-29. 6 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from; estimated values are not printed for this model and come from similar models of the same brand.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	35.75 in	✓ Verified — retained secondary source	Cafe installation document — 104288331.pdf assets.skulytics.io	Page 1
Value used by ExactFit 35.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe installation document — 104288331.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Overall Width 35-3/4 in Open original source ↗ Why this value was used Overall Width 35-3/4 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	83.6875 in	✓ Conflicting sources — resolved	Cafe installation document — 104288331.pdf assets.skulytics.io	Page 2
Value used by ExactFit 83.6875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe installation document — 104288331.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Visual table: B - Height to Top of Case = 83 11/16 in. Open original source ↗ Why this value was used Visual table: B - Height to Top of Case = 83 11/16 in. Other evidence found 83.5 in — superseded Document 104288331.pdf; page 1. Model scope: not separately recorded. Raw value: Height to Top of Case 83-11/16 in. The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	83.5 in	✓ Conflicting sources — resolved	Cafe installation document — 104288331.pdf assets.skulytics.io	Page 2
Value used by ExactFit 83.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe installation document — 104288331.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04 Visual table: A - Overall Height = 83 1/2 in. Open original source ↗ Why this value was used Visual table: A - Overall Height = 83 1/2 in. Other evidence found 83.6875 in — superseded Document 104288331.pdf; page 1. Model scope: not separately recorded. Raw value: Overall Height 83-1/2 in. The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	22.125 in	✓ Conflicting sources — resolved	Cafe installation document — 104288378.pdf assets.skulytics.io	Page 1
Value used by ExactFit 22.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe installation document — 104288378.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Exact CIC36LP2VS1/CIC36RP2VS1 specification: Case Depth Without Door 22 1/8". Open original source ↗ Why this value was used Exact CIC36LP2VS1/CIC36RP2VS1 specification: Case Depth Without Door 22 1/8". Other evidence found 23.688 in — superseded www.cafeappliances.com; location not retained. Model scope: not separately recorded. Raw value: Official exact-model page: Case Depth Without Door 23.688 in.. The final reviewed registry supersedes this earlier audit value. Open alternative source ↗ Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	24.75 in	✓ Verified — retained secondary source	Cafe installation document — 104288331.pdf assets.skulytics.io	Page 1
Value used by ExactFit 24.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe installation document — 104288331.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Depth Without Handle 24-3/4 in Open original source ↗ Why this value was used Depth Without Handle 24-3/4 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	27.31 in	✓ Conflicting sources — resolved	Cafe measurement source — CAFE-36-Integrated-Bottom-Freezer-Refrigerator-CIC36RP2VS1 Cafe	Retained specification excerpt: Reviewed cached exact-model manufacturer label: Depth with Handle = 27.31 in. Context: :\"24.75 in\"
Value used by ExactFit 27.31 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe measurement source — CAFE-36-Integrated-Bottom-Freezer-Refrigerator-CIC36RP2VS1 Cafe · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Reviewed cached exact-model manufacturer label: Depth with Handle = 27.31 in. Context: :\"24.75 in\" Reviewed: 2026-09-04 Reviewed cached exact-model manufacturer label: Depth with Handle = 27.31 in. Context: :\"24.75 in\"},{\"id\":\"2775492\",\"name\":\"Spec_WEIGHTS & DIMENSIONS_Overall Depth with Handle\",\"value\":\"27.3125 in\"},{\"id\":\"2777124\",\"name\":\"Spec_WARRANTY_Parts Warranty\",\"value\":\"Li Open original source ↗ Why this value was used Reviewed cached exact-model manufacturer label: Depth with Handle = 27.31 in. Context: :\"24.75 in\"},{\"id\":\"2775492\",\"name\":\"Spec_WEIGHTS & DIMENSIONS_Overall Depth with Handle\",\"value\":\"27.3125 in\"},{\"id\":\"2777124\",\"name\":\"Spec_WARRANTY_Parts Warranty\",\"value\":\"Li Other evidence found 24.75 in — superseded Document 104288331.pdf; page 1. Model scope: not separately recorded. Raw value: Overall Depth 24-3/4 in. The final reviewed registry supersedes this earlier audit value. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	46.375 in	✓ Verified — exact model	Cafe measurement source — CAFE-36-Integrated-Bottom-Freezer-Refrigerator-CIC36RP2VS1 Cafe	Retained specification excerpt: Official exact-model specification: Depth with Door Open 46.375 in.
Value used by ExactFit 46.375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe measurement source — CAFE-36-Integrated-Bottom-Freezer-Refrigerator-CIC36RP2VS1 Cafe · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Official exact-model specification: Depth with Door Open 46.375 in. Reviewed: 2026-09-04 Official exact-model specification: Depth with Door Open 46.375 in. Open original source ↗ Why this value was used Official exact-model specification: Depth with Door Open 46.375 in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	36 in	✓ Verified — exact model	Cafe measurement source — CAFE-36-Integrated-Bottom-Freezer-Refrigerator-CIC36RP2VS1 Cafe	Retained specification excerpt: Cutout Width: 36.0 in \| n. Cutout Dimensions (w x h x d) (in.) 36 x 84 x 25. Cutout Height (in), 84
Value used by ExactFit 36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe measurement source — CAFE-36-Integrated-Bottom-Freezer-Refrigerator-CIC36RP2VS1 Cafe · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Cutout Width: 36.0 in \| n. Cutout Dimensions (w x h x d) (in.) 36 x 84 x 25. Cutout Height (in), 84 Reviewed: 2026-09-04 Cutout Width: 36.0 in \| n. Cutout Dimensions (w x h x d) (in.) 36 x 84 x 25. Cutout Height (in), 84 in. Cutout Width (in), 36 in. Depth with Door Open, 46.375 in.Read more Open original source ↗ Why this value was used Cutout Width: 36.0 in \| n. Cutout Dimensions (w x h x d) (in.) 36 x 84 x 25. Cutout Height (in), 84 in. Cutout Width (in), 36 in. Depth with Door Open, 46.375 in.Read more Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	84 in	✓ Verified — retained secondary source · Calculated/inferred	Cafe measurement source — 104288380.pdf assets.skulytics.io	Page 15
Value used by ExactFit 84 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document Confidence label: high. Primary evidence Cafe measurement source — 104288380.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 15 Reviewed: 2026-09-05 opening 84” Open original source ↗ Why this value was used opening 84” Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	25 in	✓ Verified — retained secondary source	Cafe measurement source — CIC36RP2VS1_104288332.pdf assets.skulytics.io	Page 19
Value used by ExactFit 25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe measurement source — CIC36RP2VS1_104288332.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 19 Reviewed: 2026-09-10 Exact-model Café design guide states: The Cutout Depth Must Be 25 in. Open original source ↗ Why this value was used Exact-model Café design guide states: The Cutout Depth Must Be 25 in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	0.125 in	≈ Estimated — not printed for this model	ExactFit estimate (Cafe doesn't print this for the model) ExactFit	Not printed for this model
Value used by ExactFit 0.125 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model. Original published value and unit: see retained transcription below. Normalization: typical Café side gap (estimate) Confidence label: low. Primary evidence ExactFit estimate (Cafe doesn't print this for the model) ExactFit · Estimate Model scope: Estimate from similar models Publication/revision date: Not recorded Location: Not printed for this model Reviewed: 2026-10-29 Not printed in the Café documents we have for this model. 1/8 in is the side gap Café prints for similar models (CAE28DM5TS5, CVE28DM5NS5, CGE29DM5TS5), so it is shown as an estimate. The fit check uses Café's cutout width for this model, so this estimate does not change the fit answer. No document we have for this model prints this value. Why this value was used Not printed in the Café documents we have for this model. 1/8 in is the side gap Café prints for similar models (CAE28DM5TS5, CVE28DM5NS5, CGE29DM5TS5), so it is shown as an estimate. The fit check uses Café's cutout width for this model, so this estimate does not change the fit answer. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	0.125 in	≈ Estimated — not printed for this model	ExactFit estimate (Cafe doesn't print this for the model) ExactFit	Not printed for this model
Value used by ExactFit 0.125 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model. Original published value and unit: see retained transcription below. Normalization: typical Café side gap (estimate) Confidence label: low. Primary evidence ExactFit estimate (Cafe doesn't print this for the model) ExactFit · Estimate Model scope: Estimate from similar models Publication/revision date: Not recorded Location: Not printed for this model Reviewed: 2026-10-29 Not printed in the Café documents we have for this model. 1/8 in is the side gap Café prints for similar models (CAE28DM5TS5, CVE28DM5NS5, CGE29DM5TS5), so it is shown as an estimate. The fit check uses Café's cutout width for this model, so this estimate does not change the fit answer. No document we have for this model prints this value. Why this value was used Not printed in the Café documents we have for this model. 1/8 in is the side gap Café prints for similar models (CAE28DM5TS5, CVE28DM5NS5, CGE29DM5TS5), so it is shown as an estimate. The fit check uses Café's cutout width for this model, so this estimate does not change the fit answer. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	0.3125 in	✓ Verified — retained secondary source · Calculated/inferred	Cafe measurement source — CIC36RP2VS1_104288331.pdf assets.skulytics.io	Page 3
Value used by ExactFit 0.3125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 84 - 83.6875 Confidence label: high. Primary evidence Cafe measurement source — CIC36RP2VS1_104288331.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-09-10 Exact 84 in finished opening height on page 3 minus exact 83 11/16 in height to top of case on page 2 = 5/16 in top opening residual. Open original source ↗ All retained supporting links assets.skulytics.io ↗ · Supporting model: CIC36RP2VS1 assets.skulytics.io ↗ · Supporting model: CIC36RP2VS1 Why this value was used Exact 84 in finished opening height on page 3 minus exact 83 11/16 in height to top of case on page 2 = 5/16 in top opening residual. Calculation or inference: 84 - 83.6875. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	2.875 in	✓ Verified — retained secondary source · Calculated/inferred	Cafe measurement source — CIC36RP2VS1_104288331.pdf assets.skulytics.io	Page 3
Value used by ExactFit 2.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 25 - 22.125 Confidence label: high. Primary evidence Cafe measurement source — CIC36RP2VS1_104288331.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-09-10 Exact 25 in finished opening depth on page 3 minus exact 22 1/8 in case depth without door on page 1 = 2 7/8 in rear opening residual. Open original source ↗ All retained supporting links assets.skulytics.io ↗ · Supporting model: CIC36RP2VS1 assets.skulytics.io ↗ · Supporting model: CIC36RP2VS1 Why this value was used Exact 25 in finished opening depth on page 3 minus exact 22 1/8 in case depth without door on page 1 = 2 7/8 in rear opening residual. Calculation or inference: 25 - 22.125. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Wall clearance for door open to 90°	6.75 in	? Verified — finalized database measurement	Cafe measurement source — 104288378.pdf assets.skulytics.io	Page 2
Value used by ExactFit 6.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidence Cafe measurement source — 104288378.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-17 Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees (text also gives a fully open figure)). Exact CIC36 product-clearance table: Dim A is 6 3/4" at 90 degrees and 21 9/16" at the factory 115-degree stop. Open original source ↗ All retained supporting links assets.skulytics.io ↗ · Supporting model: CAE28DM5TS5 assets.skulytics.io ↗ · Supporting model: CIC36RP2VS1 assets.skulytics.io ↗ · Supporting model: CVE28DM5NS5 www.cafeappliances.com ↗ · Supporting model: CGE29DM5TS5 Why this value was used Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees (text also gives a fully open figure)). Exact CIC36 product-clearance table: Dim A is 6 3/4" at 90 degrees and 21 9/16" at the factory 115-degree stop. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Wall clearance for fully open door	Unknown	? Not found	Source not recorded Publisher not recorded	Exact location not retained
Value used by ExactFit Unknown · Fit role: Operating clearance. Primary evidence Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used No evidence decision recorded. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	35.75 in	✓ Verified — retained secondary source	Cafe installation document — 104288331.pdf assets.skulytics.io	Page 1
Value used by ExactFit 35.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Cafe installation document — 104288331.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Overall Width 35-3/4 in Open original source ↗ Why this value was used Overall Width 35-3/4 in Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Cabinet height

Selected: 83.6875 in. Earlier retained values: 83.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Visual table: B - Height to Top of Case = 83 11/16 in.

View source scope, location, and impact on fit

Height with hinge / controlling height

Selected: 83.5 in. Earlier retained values: 83.6875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Visual table: A - Overall Height = 83 1/2 in.

View source scope, location, and impact on fit

Depth without door

Selected: 22.125 in. Earlier retained values: 23.688 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Exact CIC36LP2VS1/CIC36RP2VS1 specification: Case Depth Without Door 22 1/8".

View source scope, location, and impact on fit

Depth with handle

Selected: 27.31 in. Earlier retained values: 24.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Reviewed cached exact-model manufacturer label: Depth with Handle = 27.31 in. Context: :\"24.75 in\"},{\"id\":\"2775492\",\"name\":\"Spec_WEIGHTS & DIMENSIONS_Overall Depth with Handle\",\"value\":\"27.3125 in\"},{\"id\":\"2777124\",\"name\":\"Spec_WARRANTY_Parts Warranty\",\"value\":\"Li

View source scope, location, and impact on fit

Measurements not established

Wall clearance for fully open door

Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.

No evidence decision recorded.

Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.

Source documents and pages

Cafe installation document — 104288331.pdf

assets.skulytics.io · Installation manual · secondary model/source

Model numbers covered: CIC36RP2VS1. Publication/revision date: Not recorded. Reviewed: 2026-09-04.

5 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth with door, without handles; Cabinet case width.