Measurement evidence for Cafe CIC36LP2VS1

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe CIC36LP2VS1 Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall Width 35-3/4 in

Why this value was used

Overall Width 35-3/4 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.6875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe CIC36LP2VS1 Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Visual table: B - Height to Top of Case = 83 11/16 in.

Why this value was used

Visual table: B - Height to Top of Case = 83 11/16 in.

Other evidence found

• 83.5 in — superseded

  104288378.pdf; page 1. Model scope: not separately recorded. Raw value: Height to Top of Case 83-11/16 in. The final reviewed registry supersedes this earlier audit value. Visual table: B - Height to Top of Case = 83 11/16 in.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe CIC36LP2VS1 Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Visual table: A - Overall Height = 83 1/2 in.

Why this value was used

Visual table: A - Overall Height = 83 1/2 in.

Other evidence found

• 83.6875 in — superseded

  104288378.pdf; page 1. Model scope: not separately recorded. Raw value: Overall Height 83-1/2 in. The final reviewed registry supersedes this earlier audit value. Visual table: A - Overall Height = 83 1/2 in.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

22.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe CIC36LP2VS1 Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Case Depth Without Door 22-1/8 in

Why this value was used

Case Depth Without Door 22-1/8 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe CIC36LP2VS1 Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth Without Handle 24-3/4 in

Why this value was used

Depth Without Handle 24-3/4 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

27.31 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

CAFÉ™ 36" Integrated Bottom-Freezer Refrigerator - CIC36LP2VS1 - Cafe Appliances
Cafe · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Reviewed cached exact-model manufacturer label: Depth with Handle = 27.31 in. Context: inge | 83.5 i
Reviewed: 2026-09-04

Reviewed cached exact-model manufacturer label: Depth with Handle = 27.31 in. Context: inge | 83.5 in | | Net Weight | 555 lb | | Overall Depth | 24.75 in | | Overall Depth with Handle | 27.3125 in | | Overall Height | 83.5 in | | Overall Width | 35.75 in | ## Reviews and Q&A

Why this value was used

Reviewed cached exact-model manufacturer label: Depth with Handle = 27.31 in. Context: inge | 83.5 in | | Net Weight | 555 lb | | Overall Depth | 24.75 in | | Overall Depth with Handle | 27.3125 in | | Overall Height | 83.5 in | | Overall Width | 35.75 in | ## Reviews and Q&A

Other evidence found

• 24.75 in — superseded

  104288378.pdf; page 1. Model scope: not separately recorded. Raw value: Overall Depth 24-3/4 in. The final reviewed registry supersedes this earlier audit value. Reviewed cached exact-model manufacturer label: Depth with Handle = 27.31 in. Context: inge | 83.5 in | | Net Weight | 555 lb | | Overall Depth | 24.75 in | | Overall Depth with Handle | 27.3125 in | | Overall Height | 83.5 in | | Overall Width | 35.75 in | ## Reviews and Q&A

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: matching CIC36 left/right hinge chassis

Confidence label: medium.

Primary evidence

CAFÉ™ 36" Integrated Bottom-Freezer Refrigerator - CIC36RP2VS1 - Cafe Appliances
Cafe · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official CIC36 specification: Depth with Door Open 46.375 in; all structural dimensions match.
Reviewed: 2026-09-04

Official CIC36 specification: Depth with Door Open 46.375 in; all structural dimensions match.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 46.375 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe CIC36LP2VS1 Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Exact-model Café quick specs, SINGLE INSTALLATION front view: opening width = 36".

Why this value was used

Exact-model Café quick specs, SINGLE INSTALLATION front view: opening width = 36".

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

84 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document

Confidence label: high.

Primary evidence

Cafe CIC36LP2VS1 Installation Instructions
assets.skulytics.io · Installation Instructions
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 15
Reviewed: 2026-09-05

opening 84”

Why this value was used

opening 84” Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Cafe CIC36LP2VS1 Installation Instructions
assets.skulytics.io · Installation Instructions
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 19
Reviewed: 2026-09-05

Electrical and water supply must be located as shown. | The Cutout Depth Must Be 25". | 6" (15.2)

Why this value was used

Electrical and water supply must be located as shown. | The Cutout Depth Must Be 25". | 6" (15.2)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe measurement source — local-cache manufacturer-family consensus
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Inferred 0.125 in per-side installation clearance from dominant manufacturer-family specification pa
Reviewed: 2026-09-05

Inferred 0.125 in per-side installation clearance from dominant manufacturer-family specification pattern.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

The retained record does not establish source scope or a resolvable supporting source.

Retained research value: 0.125 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe measurement source — local-cache manufacturer-family consensus
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Inferred 0.125 in per-side installation clearance from dominant manufacturer-family specification pa
Reviewed: 2026-09-05

Inferred 0.125 in per-side installation clearance from dominant manufacturer-family specification pattern.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

The retained record does not establish source scope or a resolvable supporting source.

Retained research value: 0.125 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.3125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_height_in - height_case_in

Confidence label: medium.

Calculation inputs: Cabinet height; Minimum cutout height;

Primary evidence

Cafe CIC36LP2VS1 Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-05

Exact 84" integrated opening less the documented 83 11/16" case height = 5/16" top opening residual.

Why this value was used

Exact 84" integrated opening less the documented 83 11/16" case height = 5/16" top opening residual. Calculation or inference: min_cutout_height_in - height_case_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in

Confidence label: medium.

Calculation inputs: Depth without door; Minimum cutout depth;

Primary evidence

Cafe CIC36LP2VS1 Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-05

Exact 25" integrated opening depth less the documented 22 1/8" case-only depth = 2 7/8" rear opening residual.

Why this value was used

Exact 25" integrated opening depth less the documented 22 1/8" case-only depth = 2 7/8" rear opening residual. Calculation or inference: min_cutout_depth_in - depth_case_only_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

6.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe CIC36LP2VS1 Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Exact CIC36 product-clearance table: Dim A is 6 3/4" at 90 degrees and 21 9/16" at the factory 115-degree stop.

Why this value was used

Exact CIC36 product-clearance table: Dim A is 6 3/4" at 90 degrees and 21 9/16" at the factory 115-degree stop.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Cafe CIC36LP2VS1 Quick Specs
assets.skulytics.io · Quick Specs
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall Width 35-3/4 in

Why this value was used

Overall Width 35-3/4 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Popular-brand chassis/type consensus: Strong modal installation clearance for this manufacturer family

Confidence label: low.

Primary evidence

Cafe measurement source — local-cache manufacturer-family consensus
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Inferred 0.125 in per-side installation clearance from dominant manufacturer-family specification pa
Reviewed: 2026-09-04

Inferred 0.125 in per-side installation clearance from dominant manufacturer-family specification pattern.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.

Retained research value: 0.125 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.