This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-18. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.625 in | ✓ Verified — exact model | Cafe measurement source — CAFE-ENERGY-STAR-28-7-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-in-Platinum-Glass-With-Dual-Dispense-AutoFill-Pitcher-CGE29DM5TS5 Cafe | Retained specification excerpt: Overall Width | 35.625 in | |
Value used by ExactFit35.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CAFE-ENERGY-STAR-28-7-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-in-Platinum-Glass-With-Dual-Dispense-AutoFill-Pitcher-CGE29DM5TS5 Overall Width | 35.625 inOpen original source ↗ Why this value was usedOverall Width | 35.625 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 68.625 in | ✓ Verified — exact model | Cafe measurement source — CAFE-ENERGY-STAR-28-7-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-in-Platinum-Glass-With-Dual-Dispense-AutoFill-Pitcher-CGE29DM5TS5 Cafe | Retained specification excerpt: Height to Top of Case | 68.625 in | |
Value used by ExactFit68.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CAFE-ENERGY-STAR-28-7-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-in-Platinum-Glass-With-Dual-Dispense-AutoFill-Pitcher-CGE29DM5TS5 Height to Top of Case | 68.625 inOpen original source ↗ Why this value was usedHeight to Top of Case | 68.625 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.8125 in | ✓ Conflicting sources — resolved | Cafe installation document — 104288600.pdf assets.skulytics.io | Page 25 | |
Value used by ExactFit69.8125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 104288600.pdf Height to Top of Hinge Cover (B) = 69-13/16 in.Open original source ↗ Why this value was usedHeight to Top of Hinge Cover (B) = 69-13/16 in. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 29.5 in | ✓ Verified — exact model | Cafe measurement source — CAFE-ENERGY-STAR-28-7-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-in-Platinum-Glass-With-Dual-Dispense-AutoFill-Pitcher-CGE29DM5TS5 Cafe | Retained specification excerpt: Case Depth Without Door | 29.5 in | |
Value used by ExactFit29.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CAFE-ENERGY-STAR-28-7-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-in-Platinum-Glass-With-Dual-Dispense-AutoFill-Pitcher-CGE29DM5TS5 Case Depth Without Door | 29.5 inOpen original source ↗ Why this value was usedCase Depth Without Door | 29.5 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 34.25 in | ✓ Verified — exact model | Cafe measurement source — CAFE-ENERGY-STAR-28-7-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-in-Platinum-Glass-With-Dual-Dispense-AutoFill-Pitcher-CGE29DM5TS5 Cafe | Retained specification excerpt: Depth Without Handle | 34.25 in | |
Value used by ExactFit34.25 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CAFE-ENERGY-STAR-28-7-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-in-Platinum-Glass-With-Dual-Dispense-AutoFill-Pitcher-CGE29DM5TS5 Depth Without Handle | 34.25 inOpen original source ↗ Why this value was usedDepth Without Handle | 34.25 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 34.25 in | ✓ Verified — exact model | Cafe measurement source — CAFE-ENERGY-STAR-28-7-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-in-Platinum-Glass-With-Dual-Dispense-AutoFill-Pitcher-CGE29DM5TS5 Cafe | Retained specification excerpt: Overall Depth with Handle | 34.25 in | |
Value used by ExactFit34.25 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CAFE-ENERGY-STAR-28-7-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-in-Platinum-Glass-With-Dual-Dispense-AutoFill-Pitcher-CGE29DM5TS5 Overall Depth with Handle | 34.25 inOpen original source ↗ Why this value was usedOverall Depth with Handle | 34.25 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 48.375 in | ✓ Verified — exact model | Cafe measurement source — CAFE-ENERGY-STAR-28-7-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-in-Platinum-Glass-With-Dual-Dispense-AutoFill-Pitcher-CGE29DM5TS5 Cafe | Retained specification excerpt: Depth with Door Open 90° | 48.375 in | |
Value used by ExactFit48.375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CAFE-ENERGY-STAR-28-7-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-in-Platinum-Glass-With-Dual-Dispense-AutoFill-Pitcher-CGE29DM5TS5 Depth with Door Open 90° | 48.375 inOpen original source ↗ Why this value was usedDepth with Door Open 90° | 48.375 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 35.875 in | ✓ Verified — exact model · Calculated/inferred | Cafe measurement source — CAFE-ENERGY-STAR-28-7-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-in-Platinum-Glass-With-Dual-Dispense-AutoFill-Pitcher-CGE29DM5TS5 Cafe | Retained specification excerpt: Official Overall Width and Side Air Clearances; width_doors_closed_in + 2 * side_clearance_wall_in = | |
Value used by ExactFit35.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: width_doors_closed_in + 2 * side_ventilation_clearance_in = 35.875 Confidence label: high. Calculation inputs: Overall width; Left-side ventilation clearance; Primary evidenceCafe measurement source — CAFE-ENERGY-STAR-28-7-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-in-Platinum-Glass-With-Dual-Dispense-AutoFill-Pitcher-CGE29DM5TS5 Official Overall Width and Side Air Clearances; width_doors_closed_in + 2 * side_clearance_wall_in = 35.875 in | Formula text updated 2026-09-18: the side gap it used was the side ventilation clearance (side_clearance_wall_in was retired); the value is unchanged.Open original source ↗ Why this value was usedOfficial Overall Width and Side Air Clearances; width_doors_closed_in + 2 * side_clearance_wall_in = 35.875 in | Formula text updated 2026-09-18: the side gap it used was the side ventilation clearance (side_clearance_wall_in was retired); the value is unchanged. Calculation or inference: width_doors_closed_in + 2 * side_ventilation_clearance_in = 35.875. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 70.8125 in | ✓ Verified — retained secondary source · Calculated/inferred | Cafe measurement source — CGE29DM5TS5_104288600.pdf assets.skulytics.io | Page 24 | |
Value used by ExactFit70.8125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(68.625, 69.8125) + 1 Confidence label: high. Primary evidenceCafe measurement source — CGE29DM5TS5_104288600.pdf Exact 69 13/16 in hinge-cover height plus the directly printed 1 in top clearance.Open original source ↗ All retained supporting links
Why this value was usedExact 69 13/16 in hinge-cover height plus the directly printed 1 in top clearance. Calculation or inference: max(68.625, 69.8125) + 1. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 31.5 in | ✓ Verified — retained secondary source · Calculated/inferred | Cafe measurement source — CGE29DM5TS5_104288600.pdf assets.skulytics.io | Page 24 | |
Value used by ExactFit31.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 29.5 + 2 Confidence label: high. Primary evidenceCafe measurement source — CGE29DM5TS5_104288600.pdf Exact 29 1/2 in case depth without door plus the directly printed 2 in back clearance.Open original source ↗ All retained supporting links
Why this value was usedExact 29 1/2 in case depth without door plus the directly printed 2 in back clearance. Calculation or inference: 29.5 + 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — exact model | Cafe measurement source — CAFE-ENERGY-STAR-28-7-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-in-Platinum-Glass-With-Dual-Dispense-AutoFill-Pitcher-CGE29DM5TS5 Cafe | Retained specification excerpt: Side Air Clearances | 1/8 in | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CAFE-ENERGY-STAR-28-7-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-in-Platinum-Glass-With-Dual-Dispense-AutoFill-Pitcher-CGE29DM5TS5 Side Air Clearances | 1/8 inOpen original source ↗ Why this value was usedSide Air Clearances | 1/8 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — exact model | Cafe measurement source — CAFE-ENERGY-STAR-28-7-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-in-Platinum-Glass-With-Dual-Dispense-AutoFill-Pitcher-CGE29DM5TS5 Cafe | Retained specification excerpt: Side Air Clearances | 1/8 in | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CAFE-ENERGY-STAR-28-7-Cu-Ft-Smart-4-Door-French-Door-Refrigerator-in-Platinum-Glass-With-Dual-Dispense-AutoFill-Pitcher-CGE29DM5TS5 Side Air Clearances | 1/8 inOpen original source ↗ Why this value was usedSide Air Clearances | 1/8 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 1 in | ✓ Verified — retained secondary source | Cafe measurement source — CGE29DM5TS5_104288600.pdf assets.skulytics.io | Page 24 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CGE29DM5TS5_104288600.pdf CGE/CJE manufacturer CLEARANCES block directly prints Top = 1 in.Open original source ↗ All retained supporting links
Why this value was usedCGE/CJE manufacturer CLEARANCES block directly prints Top = 1 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Verified — retained secondary source | Cafe measurement source — CGE29DM5TS5_104288600.pdf assets.skulytics.io | Page 24 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CGE29DM5TS5_104288600.pdf CGE/CJE manufacturer CLEARANCES block directly prints Back = 2 in.Open original source ↗ All retained supporting links
Why this value was usedCGE/CJE manufacturer CLEARANCES block directly prints Back = 2 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 1.9375 in | ✓ Verified — retained secondary source · Calculated/inferred | Cafe measurement source — CGE29DM5TS5_104288600.pdf assets.skulytics.io | Page 24 | |
Value used by ExactFit1.9375 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (39.5 - 35.625) / 2 Confidence label: high. Primary evidenceCafe measurement source — CGE29DM5TS5_104288600.pdf Migrated from hinge_side_wall_clearance_in (90 degrees). Exact-model Cafe installation table visually prints glass-door width open 90 degrees as 39 1/2 in and closed width as 35 5/8 in; symmetric per-side operating envelope is 1 15/16 in.Open original source ↗ All retained supporting links
Why this value was usedMigrated from hinge_side_wall_clearance_in (90 degrees). Exact-model Cafe installation table visually prints glass-door width open 90 degrees as 39 1/2 in and closed width as 35 5/8 in; symmetric per-side operating envelope is 1 15/16 in. Calculation or inference: (39.5 - 35.625) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.625 in | ✓ Verified — retained secondary source | Cafe measurement source — CGE29DM5TS5_104288600.pdf assets.skulytics.io | Page 24 | |
Value used by ExactFit35.625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CGE29DM5TS5_104288600.pdf CGE/CJE manufacturer dimension table directly prints H, Case Width = 35 5/8 in for the full-depth glass-door configuration.Open original source ↗ All retained supporting links
Why this value was usedCGE/CJE manufacturer dimension table directly prints H, Case Width = 35 5/8 in for the full-depth glass-door configuration. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 69.8125 in. Earlier retained values: 70 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Height to Top of Hinge Cover (B) = 69-13/16 in.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Cafe · Web source · exact model/source
Model numbers covered: CGE29DM5TS5. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
9 displayed measurements supported: Overall width; Cabinet height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Left-side ventilation clearance; Right-side ventilation clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: CGE29DM5TS5. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Height with hinge / controlling height.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: CGE29DM5TS5. Publication/revision date: Not recorded. Reviewed: 2026-09-10.
6 displayed measurements supported: Minimum cutout height; Minimum cutout depth; Top clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-18. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.