This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Bottom Freezer · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-24. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.625 in | ✓ Verified — retained secondary source | Cafe installation document — 104288728.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 104288728.pdf Overall Width 35-5/8 inOpen original source ↗ Why this value was usedOverall Width 35-5/8 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 68.625 in | ✓ Verified — retained secondary source | Cafe installation document — 104288728.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit68.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 104288728.pdf Height to Top of Case 68-5/8 inOpen original source ↗ Why this value was usedHeight to Top of Case 68-5/8 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.875 in | ✓ Conflicting sources — resolved | Cafe measurement source — 104288728.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit69.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — 104288728.pdf Height to top of door 69-7/8 in; the same table prints Height to top of hinge 69-3/4 and Height to top of case 68-5/8. The stored field holds the appliance's overall height for fit, so it takes the highest point, the top of the door (owner decision 2026-09-24).Open original source ↗ Why this value was usedHeight to top of door 69-7/8 in; the same table prints Height to top of hinge 69-3/4 and Height to top of case 68-5/8. The stored field holds the appliance's overall height for fit, so it takes the highest point, the top of the door (owner decision 2026-09-24). Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 29.5 in | ✓ Verified — retained secondary source | Cafe installation document — 104288728.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit29.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 104288728.pdf Case Depth Without Door 29-1/2 inOpen original source ↗ Why this value was usedCase Depth Without Door 29-1/2 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 34.25 in | ✓ Verified — retained secondary source | Cafe installation document — 104288728.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit34.25 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 104288728.pdf Depth Without Handle 34-1/4 inOpen original source ↗ Why this value was usedDepth Without Handle 34-1/4 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 34.25 in | ✓ Verified — retained secondary source | Cafe installation document — 104288728.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit34.25 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 104288728.pdf Overall Depth 34-1/4 inOpen original source ↗ Why this value was usedOverall Depth 34-1/4 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 48.375 in | ✓ Conflicting sources — resolved | Cafe measurement source — CAFE-ENERGY-STAR-28-3-Cu-Ft-Smart-Quad-Door-Refrigerator-in-Platinum-Glass-with-Dual-Dispense-AutoFill-Pitcher-CAE28DM5TS5 Cafe | Retained specification excerpt: Official exact-model page: Depth with Door Open 90 degrees 48.375 in. | |
Value used by ExactFit48.375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CAFE-ENERGY-STAR-28-3-Cu-Ft-Smart-Quad-Door-Refrigerator-in-Platinum-Glass-with-Dual-Dispense-AutoFill-Pitcher-CAE28DM5TS5 Official exact-model page: Depth with Door Open 90 degrees 48.375 in.Open original source ↗ Why this value was usedOfficial exact-model page: Depth with Door Open 90 degrees 48.375 in. Other evidence found
Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 35.875 in | ✓ Verified — retained secondary source · Calculated/inferred | Cafe measurement source — CAE28DM5TS5_104288728.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 35.625 + 2 * 0.125 Confidence label: high. Primary evidenceCafe measurement source — CAE28DM5TS5_104288728.pdf Exact closed width plus the explicitly printed side air clearance on both sides.Open original source ↗ Why this value was usedExact closed width plus the explicitly printed side air clearance on both sides. Calculation or inference: 35.625 + 2 * 0.125. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 70.75 in | ✓ Verified — retained secondary source · Calculated/inferred | Cafe measurement source — CAE28DM5TS5_104288728.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit70.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(68.625, 69.75) + 1 Confidence label: high. Primary evidenceCafe measurement source — CAE28DM5TS5_104288728.pdf Highest exact appliance-height endpoint plus the explicitly printed top air clearance.Open original source ↗ Why this value was usedHighest exact appliance-height endpoint plus the explicitly printed top air clearance. Calculation or inference: max(68.625, 69.75) + 1. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 31.5 in | ✓ Verified — retained secondary source · Calculated/inferred | Cafe measurement source — CAE28DM5TS5_104288728.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit31.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 29.5 + 2 Confidence label: high. Primary evidenceCafe measurement source — CAE28DM5TS5_104288728.pdf Exact case depth without door plus the explicitly printed back air clearance.Open original source ↗ Why this value was usedExact case depth without door plus the explicitly printed back air clearance. Calculation or inference: 29.5 + 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Cafe measurement source — 104288728.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — 104288728.pdf Side air clearances = 1/8"Open original source ↗ Why this value was usedSide air clearances = 1/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Cafe measurement source — 104288728.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — 104288728.pdf Side air clearances = 1/8"Open original source ↗ Why this value was usedSide air clearances = 1/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 1 in | ✓ Verified — retained secondary source | Cafe measurement source — CAE28DM5TS5_104288728.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CAE28DM5TS5_104288728.pdf Exact retained Café Quick Specs page 1 directly prints Top Air Clearance = 1 in.Open original source ↗ Why this value was usedExact retained Café Quick Specs page 1 directly prints Top Air Clearance = 1 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 2 in | ✓ Verified — retained secondary source | Cafe measurement source — CAE28DM5TS5_104288728.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe measurement source — CAE28DM5TS5_104288728.pdf Exact retained Café Quick Specs page 1 directly prints Back Air Clearance = 2 in.Open original source ↗ Why this value was usedExact retained Café Quick Specs page 1 directly prints Back Air Clearance = 2 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 1.96875 in | ✓ Verified — retained secondary source · Calculated/inferred | Cafe measurement source — CAE28DM5TS5_104288728.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit1.96875 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (39.5625 - 35.625) / 2 Confidence label: high. Primary evidenceCafe measurement source — CAE28DM5TS5_104288728.pdf Migrated from hinge_side_wall_clearance_in (90 degrees). Exact-model Cafe specification visually prints width with symmetric doors open 90 degrees including handles as 39.5625 in and closed case width as 35.625 in; exact per-side operating envelope is (39.5625 - 35.625) / 2 = 1.96875 in.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in (90 degrees). Exact-model Cafe specification visually prints width with symmetric doors open 90 degrees including handles as 39.5625 in and closed case width as 35.625 in; exact per-side operating envelope is (39.5625 - 35.625) / 2 = 1.96875 in. Calculation or inference: (39.5625 - 35.625) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.625 in | ✓ Verified — retained secondary source | Cafe installation document — 104288728.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceCafe installation document — 104288728.pdf Overall Width 35-5/8 inOpen original source ↗ Why this value was usedOverall Width 35-5/8 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 69.875 in. Earlier retained values: 69.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Height to top of door 69-7/8 in; the same table prints Height to top of hinge 69-3/4 and Height to top of case 68-5/8. The stored field holds the appliance's overall height for fit, so it takes the highest point, the top of the door (owner decision 2026-09-24).
View source scope, location, and impact on fitSelected: 48.375 in. Earlier retained values: 43.375 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Official exact-model page: Depth with Door Open 90 degrees 48.375 in.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: CAE28DM5TS5. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
9 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Left-side ventilation clearance; Right-side ventilation clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Cafe · Web source · exact model/source
Model numbers covered: CAE28DM5TS5. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Depth with doors open at 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: CAE28DM5TS5. Publication/revision date: Not recorded. Reviewed: 2026-09-17.
6 displayed measurements supported: Minimum cutout width; Minimum cutout height; Minimum cutout depth; Top clearance; Rear clearance; Wall clearance for door open to 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-24. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.