This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-24. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.75 in | ✓ Conflicting sources — resolved | Bosch measurement source — 96878107.pdf Bosch | Page 2 | |
Value used by ExactFit35.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — 96878107.pdf Custom panels installed and closed: 35 3/4 in across the panels; the case width is 35 1/4 in.Open original source ↗ Why this value was usedCustom panels installed and closed: 35 3/4 in across the panels; the case width is 35 1/4 in. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 83.5625 in | ✓ Conflicting sources — resolved | Bosch installation document — 96878107.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit83.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch installation document — 96878107.pdf exact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpointOpen original source ↗ Why this value was usedexact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpoint Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 83.5625 in | ✓ Conflicting sources — resolved | Bosch measurement source — a70ca2a8994a258ea0e35cf26011c6baf358cff2c2ceb4aae4f46e05f244e206.json Bosch | Retained specification excerpt: Cached official Bosch page: overall appliance height 83 9/16 in; 84 in is the niche height. | |
Value used by ExactFit83.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — a70ca2a8994a258ea0e35cf26011c6baf358cff2c2ceb4aae4f46e05f244e206.json Cached official Bosch page: overall appliance height 83 9/16 in; 84 in is the niche height.Open original source ↗ Why this value was usedCached official Bosch page: overall appliance height 83 9/16 in; 84 in is the niche height. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24 in | ✓ Verified — retained secondary source | Bosch installation document — 96878107.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch installation document — 96878107.pdf Overall depth without doors and handles (inches) -> 24"Open original source ↗ Why this value was usedOverall depth without doors and handles (inches) -> 24" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 24 in | ✓ Conflicting sources — resolved | Bosch installation document — 96878107.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit24 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch installation document — 96878107.pdf exact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpointOpen original source ↗ Why this value was usedexact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpoint Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 25 in | ✓ Verified — retained secondary source | Bosch installation document — 96878107.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit25 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch installation document — 96878107.pdf HxWxD) (inches) 84" x 36" x 25"Open original source ↗ Why this value was usedHxWxD) (inches) 84" x 36" x 25" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 45 in | ✓ Conflicting sources — resolved · Calculated/inferred | Bosch measurement source — B36IT100NP-96878107.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit45 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: printed cutout depth 25 in + printed 90-degree forward projection 20 in = 45 in Confidence label: high. Primary evidenceBosch measurement source — B36IT100NP-96878107.pdf Exact-model flush-install top view prints a 25 in rear cavity and a 20 in forward projection at 90 degrees; the shared reference plane makes the full rear-to-front envelope exactly 45 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model flush-install top view prints a 25 in rear cavity and a 20 in forward projection at 90 degrees; the shared reference plane makes the full rear-to-front envelope exactly 45 in. Calculation or inference: printed cutout depth 25 in + printed 90-degree forward projection 20 in = 45 in. Other evidence found
Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Conflicting sources — resolved | Bosch measurement source — B36IT100NP-96878107.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36IT100NP-96878107.pdf Exact-model summary directly prints required cutout width 36 in.Open original source ↗ Why this value was usedExact-model summary directly prints required cutout width 36 in. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 84 in | ✓ Verified — retained secondary source | Bosch measurement source — 96878107.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — 96878107.pdf cutout size (HxWxD) (inches) 84"Open original source ↗ Why this value was usedcutout size (HxWxD) (inches) 84" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Conflicting sources — resolved | Bosch measurement source — B36IT100NP-96878107.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36IT100NP-96878107.pdf Exact-model Bosch summary directly prints required cutout size 84 x 36 x 25 in; the installation drawing repeats at least 25 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model Bosch summary directly prints required cutout size 84 x 36 x 25 in; the installation drawing repeats at least 25 in. Other evidence found
Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.375 in | ✓ Verified — retained secondary source | Bosch measurement source — B36IT100NP-96878107.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36IT100NP-96878107.pdf Exact-model flush-install top view directly prints a 3/8 in side gap between the appliance and enclosure.Open original source ↗ All retained supporting links
Why this value was usedExact-model flush-install top view directly prints a 3/8 in side gap between the appliance and enclosure. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.375 in | ✓ Verified — retained secondary source | Bosch measurement source — B36IT100NP-96878107.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36IT100NP-96878107.pdf Exact-model flush-install top view directly prints a 3/8 in side gap between the appliance and enclosure.Open original source ↗ All retained supporting links
Why this value was usedExact-model flush-install top view directly prints a 3/8 in side gap between the appliance and enclosure. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.4375 in | ✓ Verified — retained secondary source · Calculated/inferred | Bosch measurement source — B36IT100NP-96878107.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit0.4375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 84 - 83.5625 Confidence label: high. Primary evidenceBosch measurement source — B36IT100NP-96878107.pdf Exact-model sheet prints an 84 in required cutout height and 83 9/16 in minimum appliance height; exact minimum-setting residual is 7/16 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model sheet prints an 84 in required cutout height and 83 9/16 in minimum appliance height; exact minimum-setting residual is 7/16 in. Calculation or inference: 84 - 83.5625. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Conflicting sources — resolved · Calculated/inferred | Bosch measurement source — B36IT100NP-96878107.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 25 - 24 Confidence label: high. Primary evidenceBosch measurement source — B36IT100NP-96878107.pdf Exact-model sheet prints a 25 in required flush cutout depth and 24 in appliance body depth without doors and handles; exact rear cavity residual is 1 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model sheet prints a 25 in required flush cutout depth and 24 in appliance body depth without doors and handles; exact rear cavity residual is 1 in. Calculation or inference: 25 - 24. Other evidence found
Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.25 in | ✓ Conflicting sources — resolved | Bosch measurement source — a70ca2a8994a258ea0e35cf26011c6baf358cff2c2ceb4aae4f46e05f244e206.json Bosch | Retained specification excerpt: Cached official Bosch page: overall appliance width 35 1/4 in; replaces nominal 36 in. | |
Value used by ExactFit35.25 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — a70ca2a8994a258ea0e35cf26011c6baf358cff2c2ceb4aae4f46e05f244e206.json Cached official Bosch page: overall appliance width 35 1/4 in; replaces nominal 36 in.Open original source ↗ Why this value was usedCached official Bosch page: overall appliance width 35 1/4 in; replaces nominal 36 in. Other evidence found
Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 35.75 in. Earlier retained values: 36 in, 35.25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Custom panels installed and closed: 35 3/4 in across the panels; the case width is 35 1/4 in.
View source scope, location, and impact on fitSelected: 83.5625 in. Earlier retained values: 84 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
exact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpoint
View source scope, location, and impact on fitSelected: 83.5625 in. Earlier retained values: 84 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Cached official Bosch page: overall appliance height 83 9/16 in; 84 in is the niche height.
View source scope, location, and impact on fitSelected: 24 in. Earlier retained values: 25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
exact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpoint
View source scope, location, and impact on fitSelected: 45 in. Earlier retained values: 44.2126 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model flush-install top view prints a 25 in rear cavity and a 20 in forward projection at 90 degrees; the shared reference plane makes the full rear-to-front envelope exactly 45 in. Calculation or inference: printed cutout depth 25 in + printed 90-degree forward projection 20 in = 45 in.
View source scope, location, and impact on fitSelected: 36 in. Earlier retained values: 36.25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model summary directly prints required cutout width 36 in.
View source scope, location, and impact on fitSelected: 25 in. Earlier retained values: 24 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model Bosch summary directly prints required cutout size 84 x 36 x 25 in; the installation drawing repeats at least 25 in.
View source scope, location, and impact on fitSelected: 1 in. Earlier retained values: 0 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model sheet prints a 25 in required flush cutout depth and 24 in appliance body depth without doors and handles; exact rear cavity residual is 1 in. Calculation or inference: 25 - 24.
View source scope, location, and impact on fitSelected: 35.25 in. Earlier retained values: 36 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Cached official Bosch page: overall appliance width 35 1/4 in; replaces nominal 36 in.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Web source · secondary model/source
Model numbers covered: B36IT100NP. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
6 displayed measurements supported: Overall width; Cabinet height; Depth without door; Depth with door, without handles; Depth with handle; Minimum cutout height.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Bosch · Web source · exact model/source
Model numbers covered: B36IT100NP. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Height with hinge / controlling height; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: B36IT100NP. Publication/revision date: Not recorded. Reviewed: 2026-09-11.
7 displayed measurements supported: Depth with doors open at 90°; Minimum cutout width; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-24. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.