Measurement evidence for Bosch B36FD52SNS

Value used by ExactFit

35.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — 102943543.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-09

Exact Bosch closed front view prints overall width 35 5/8 in.

Why this value was used

Exact Bosch closed front view prints overall width 35 5/8 in.

Other evidence found

• 36 in — superseded

  Document 102943543.pdf; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 36" x 25". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 102943543.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

exact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpoint

Why this value was used

exact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpoint

Other evidence found

• 70 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 36" x 25". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 102943543.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

HxWxD) (inches) 70" x 36" x 25"

Why this value was used

HxWxD) (inches) 70" x 36" x 25"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.3125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — 102943543.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-17

Spec sheet page 2 prints 29-5/16 in (745 mm) from the rear spacer face to the case front: the 28-3/8 in (720 mm) cabinet plus the 1 in (25 mm) fixed rear spacers of note B. Owner ruling 2026-09-16: this field includes fixed rear spacers.

Why this value was used

Spec sheet page 2 prints 29-5/16 in (745 mm) from the rear spacer face to the case front: the 28-3/8 in (720 mm) cabinet plus the 1 in (25 mm) fixed rear spacers of note B. Owner ruling 2026-09-16: this field includes fixed rear spacers.

Other evidence found

• 28.375 in — superseded

  The same document as the value used above; page 2. Model scope: not separately recorded. Raw value: Exact diagram: depth without doors/case-only = 28-3/8 in; rear fixed-spacer allowance is separate.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

33.125 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — B36FD52SNS_102943543.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-07

Exact manufacturer detailed diagram 33 1/8 in; confirmed by identical B36FD52SNB finish sibling endpoint.

Why this value was used

Exact manufacturer detailed diagram 33 1/8 in; confirmed by identical B36FD52SNB finish sibling endpoint.

Other evidence found

• 25 in — superseded

  Document 102943543.pdf; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 36" x 25". The final reviewed registry supersedes this earlier audit value.

• 32.125 in — superseded

  Document Bosch B36FD52 manufacturer specification sheet cached from images.webfronts.com; location not retained. Model scope: not separately recorded. Raw value: Corrected prior value 25 in (HxWxD) (inches) 70" x 36" x 25"). B36FD52 exact listing/specification alignment: handleless depth 32 1/8 in; replaces 25-inch cutout depth.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.4375 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — B36FD52SNS_102943543.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-17

Spec sheet page 2 top view prints 35-7/16 in (900 mm) to the handle face. The page 1 table value of 32-1/8 in contradicts the drawings and is smaller than the 33-1/8 in door depth; owner ruled for the drawing on 2026-09-16.

Why this value was used

Spec sheet page 2 top view prints 35-7/16 in (900 mm) to the handle face. The page 1 table value of 32-1/8 in contradicts the drawings and is smaller than the 33-1/8 in door depth; owner ruled for the drawing on 2026-09-16.

Other evidence found

• 25 in — superseded

  Document 102943543.pdf; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 36" x 25". The final reviewed registry supersedes this earlier audit value.

• 32.125 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Exact-model Bosch summary directly prints overall depth with doors and handles as 32 1/8 in. Larger page-2 dimensions use a different rear reference/installation envelope and are not loaded into this product-depth field.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

47.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — B36FD52SNS_102943543.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Exact-model 90-degree plan view directly prints rear-to-front open-door envelope 47 3/4 in.

Why this value was used

Exact-model 90-degree plan view directly prints rear-to-front open-door envelope 47 3/4 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — 102943543.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-09

Exact Bosch installation drawing directly prints minimum opening width 36 in.

Why this value was used

Exact Bosch installation drawing directly prints minimum opening width 36 in.

Other evidence found

• 36.25 in — superseded

  An earlier brand-wide assumption (no document for this model); location not retained. Model scope: not separately recorded. Raw value: Derived minimum opening width 36.25 in from product width 36.0 in and explicit 0.125 in clearance on each side.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — B36FD52SNS_102943543.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-10

Required cutout size directly prints height 70 in; do not add the separately stated top ventilation gap to the printed cutout endpoint.

Why this value was used

Required cutout size directly prints height 70 in; do not add the separately stated top ventilation gap to the printed cutout endpoint.

Other evidence found

• 70.5 in — superseded

  Document 102943543.pdf; page 2. Model scope: not separately recorded. Raw value: 70 in overall height plus documented 1/2 in top ventilation = 70 1/2 in opening.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.3125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 28-3/8 in (720 mm) cabinet + 1 in (25 mm) fixed rear spacers = 29-5/16 in (745 mm)

Confidence label: high.

Primary evidence

Bosch measurement source — B36FD52SNS_102943543.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-17

Calculated, owner decision 2026-09-16. The page 1 table prints 25 in, impossible for a 28-3/8 in cabinet and matching the counter-depth sibling sheet. On the counter-depth model Bosch prints cutout depth = cabinet + fixed spacers; page 2 here prints that sum as 29-5/16 in (745 mm).

Why this value was used

Calculated, owner decision 2026-09-16. The page 1 table prints 25 in, impossible for a 28-3/8 in cabinet and matching the counter-depth sibling sheet. On the counter-depth model Bosch prints cutout depth = cabinet + fixed spacers; page 2 here prints that sum as 29-5/16 in (745 mm). Calculation or inference: 28-3/8 in (720 mm) cabinet + 1 in (25 mm) fixed rear spacers = 29-5/16 in (745 mm).

Other evidence found

• 29.375 in — superseded

  Document 102943543.pdf; page 2. Model scope: not separately recorded. Raw value: Installation envelope is cabinet depth plus the documented 1 in rear ventilation gap.. The final reviewed registry supersedes this earlier audit value.

• 25 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Required cutout size directly prints depth 25 in; this manufacturer cutout endpoint supersedes cabinet-depth-plus-rear-gap calculations.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — B36FD52SNS_102943543.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Exact-model installation drawing directly prints 1/8 in at each side of the 36-inch opening.

Why this value was used

Exact-model installation drawing directly prints 1/8 in at each side of the 36-inch opening.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — B36FD52SNS_102943543.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Exact-model installation drawing directly prints 1/8 in at each side of the 36-inch opening.

Why this value was used

Exact-model installation drawing directly prints 1/8 in at each side of the 36-inch opening.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 102943543.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Exact Bosch manual: leave 1/2 in gap at the top for proper ventilation.

Why this value was used

Exact Bosch manual: leave 1/2 in gap at the top for proper ventilation.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 102943543.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Exact Bosch manual: leave 1 in behind for proper ventilation.

Why this value was used

Exact Bosch manual: leave 1 in behind for proper ventilation.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — 102943543.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-25

Exact-model Bosch installation details, top view with the doors open 90°: 1 3/4" (45 mm) beyond the cabinet side (same Bosch layout).

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Exact-model Bosch installation details, top view with the doors open 90°: 1 3/4" (45 mm) beyond the cabinet side (same Bosch layout).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.625 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — 102943543.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-09

Exact Bosch dimension drawing prints product/cabinet width 35 5/8 in.

Why this value was used

Exact Bosch dimension drawing prints product/cabinet width 35 5/8 in.

Other evidence found

• 36 in — superseded

  Document 102943543.pdf; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 36" x 25". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.