Measurement evidence for Bosch B36FD10ENS

Value used by ExactFit

35.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 91072830.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Overall width = 35 5/8"

Why this value was used

Overall width = 35 5/8"

Other evidence found

• 36 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 36" x 25". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 91072830.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

exact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpoint

Why this value was used

exact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpoint

Other evidence found

• 70 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 36" x 25". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 91072830.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

HxWxD) (inches) 70" x 36" x 25"

Why this value was used

HxWxD) (inches) 70" x 36" x 25"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.3125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — 91072830.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-18

Page 2 side view prints 29-5/16" (745 mm) from the rear spacer face to the case front: the 28-3/8" (720 mm) cabinet plus "Add 1" (25 mm) for fixed spacers on back". Case-only depth includes fixed rear spacers (owner ruling 2026-09-16).

Why this value was used

Page 2 side view prints 29-5/16" (745 mm) from the rear spacer face to the case front: the 28-3/8" (720 mm) cabinet plus "Add 1" (25 mm) for fixed spacers on back". Case-only depth includes fixed rear spacers (owner ruling 2026-09-16).

Other evidence found

• 28.375 in — superseded

  Document 91072830.pdf; page 1. Model scope: not separately recorded. Raw value: Overall depth without doors and handles (inches) -> 28 3/8". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

33.125 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — 91072830.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-18

Page 2 side view prints the doors at 33-1/8" (841 mm) from the rear; the model has integrated handles, so depth with and without handles are the same. The previous 28-3/4 in appears on neither page.

Why this value was used

Page 2 side view prints the doors at 33-1/8" (841 mm) from the rear; the model has integrated handles, so depth with and without handles are the same. The previous 28-3/4 in appears on neither page.

Other evidence found

• 25 in — superseded

  Document 91072830.pdf; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 36" x 25". The final reviewed registry supersedes this earlier audit value.

• 28.75 in — superseded

  Document 91072830.pdf; page 2. Model scope: not separately recorded. Raw value: Overall depth without doors and handles = 28 3/4". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

33.125 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 91072830.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Overall depth with doors and handles = 33 1/8"

Why this value was used

Overall depth with doors and handles = 33 1/8"

Other evidence found

• 25 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 36" x 25". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

47.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — B36FD10ENS-91072830.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Exact-model 90-degree plan directly prints rear-to-front open-door envelope 47 3/4 in.

Why this value was used

Exact-model 90-degree plan directly prints rear-to-front open-door envelope 47 3/4 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 91072830.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Required cutout size HxWxD = 70" x 36" x 25"

Why this value was used

Required cutout size HxWxD = 70" x 36" x 25"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — B36FD10ENS-91072830.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-10

Required cutout size directly prints height 70 in; do not add the separately stated 1/2-inch top ventilation gap.

Why this value was used

Required cutout size directly prints height 70 in; do not add the separately stated 1/2-inch top ventilation gap.

Other evidence found

• 70.5 in — superseded

  Document 91072830.pdf; page 2. Model scope: not separately recorded. Raw value: 70 in overall height plus documented 1/2 in top ventilation = 70 1/2 in opening.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.3125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 28-3/8 in (720 mm) cabinet + 1 in (25 mm) fixed rear spacers = 29-5/16 in (745 mm)

Confidence label: high.

Primary evidence

Bosch measurement source — 91072830.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-18

Calculated as for B36FD52SNS (owner decision 2026-09-16): the page 1 table prints a 25 in cutout depth, impossible for a 28-3/8 in cabinet with 1 in fixed spacers; the table is copied from the counter-depth model.

Why this value was used

Calculated as for B36FD52SNS (owner decision 2026-09-16): the page 1 table prints a 25 in cutout depth, impossible for a 28-3/8 in cabinet with 1 in fixed spacers; the table is copied from the counter-depth model. Calculation or inference: 28-3/8 in (720 mm) cabinet + 1 in (25 mm) fixed rear spacers = 29-5/16 in (745 mm).

Other evidence found

• 29.375 in — superseded

  The same document as the value used above; page 2. Model scope: not separately recorded. Raw value: Installation envelope is cabinet depth plus the documented 1 in rear ventilation gap.. The final reviewed registry supersedes this earlier audit value.

• 25 in — superseded

  assets.skulytics.io; page 1. Model scope: not separately recorded. Raw value: Required cutout size directly prints depth 25 in; the standard-depth appliance projects beyond this cavity by design.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model.

Original published value and unit: see retained transcription below. Normalization: typical Bosch side gap (estimate)

Confidence label: low.

Primary evidence

ExactFit estimate (Bosch doesn't print this for the model)
ExactFit · Estimate
Model scope: Estimate from similar models
Publication/revision date: Not recorded
Location: Not printed for this model
Reviewed: 2026-10-29

Not printed in the Bosch documents we have for this model. 1/8 in is the side gap Bosch prints for similar models (B36CL81ENG), so it is shown as an estimate. The fit check uses Bosch's cutout width for this model, so this estimate does not change the fit answer.

No document we have for this model prints this value.

Why this value was used

Not printed in the Bosch documents we have for this model. 1/8 in is the side gap Bosch prints for similar models (B36CL81ENG), so it is shown as an estimate. The fit check uses Bosch's cutout width for this model, so this estimate does not change the fit answer.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model.

Original published value and unit: see retained transcription below. Normalization: typical Bosch side gap (estimate)

Confidence label: low.

Primary evidence

ExactFit estimate (Bosch doesn't print this for the model)
ExactFit · Estimate
Model scope: Estimate from similar models
Publication/revision date: Not recorded
Location: Not printed for this model
Reviewed: 2026-10-29

Not printed in the Bosch documents we have for this model. 1/8 in is the side gap Bosch prints for similar models (B36CL81ENG), so it is shown as an estimate. The fit check uses Bosch's cutout width for this model, so this estimate does not change the fit answer.

No document we have for this model prints this value.

Why this value was used

Not printed in the Bosch documents we have for this model. 1/8 in is the side gap Bosch prints for similar models (B36CL81ENG), so it is shown as an estimate. The fit check uses Bosch's cutout width for this model, so this estimate does not change the fit answer.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 91072830.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Exact Bosch manual: leave 1/2 in gap at the top for proper ventilation.

Why this value was used

Exact Bosch manual: leave 1/2 in gap at the top for proper ventilation.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 91072830.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Exact Bosch manual: leave 1 in behind for proper ventilation.

Why this value was used

Exact Bosch manual: leave 1 in behind for proper ventilation.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — 91072830.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-25

Exact-model Bosch installation details, top view with the doors open 90°: 1 3/4" (45 mm) beyond the cabinet side.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Exact-model Bosch installation details, top view with the doors open 90°: 1 3/4" (45 mm) beyond the cabinet side.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.625 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 91072830.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official sheet: Overall width = 35 5/8 in; 36 in is required cutout width.
Reviewed: 2026-09-04

Official sheet: Overall width = 35 5/8 in; 36 in is required cutout width.

Why this value was used

Official sheet: Overall width = 35 5/8 in; 36 in is required cutout width.

Other evidence found

• 36 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: HxWxD) (inches) 70" x 36" x 25". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.