This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-17. 1 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
Measurements and supporting evidence
Measurement
Value used
Evidence status
Primary source
Location
Details
Overall width
35.625 in
? Verified — finalized database measurement
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded
Page 1
Value used by ExactFit
35.625 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-10-17
page 1 Dimensions & Weight table: 35 5/8 in (? mm), outermost left closed-door/product side to outermost right closed-door/product side.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 1 Dimensions & Weight table: 35 5/8 in (? mm), outermost left closed-door/product side to outermost right closed-door/product side.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded
Page 2
Value used by ExactFit
71.5 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 perspective and side-profile drawings; also page 1 without hinges and doors row: 71 1/2 in (1815 mm), floor/bottom of case to top of cabinet, excluding the projecting hinge cover.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 perspective and side-profile drawings; also page 1 without hinges and doors row: 71 1/2 in (1815 mm), floor/bottom of case to top of cabinet, excluding the projecting hinge cover.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded
Page 2
Value used by ExactFit
72 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 perspective and side-profile drawings; also page 1 rows with hinges: 72 in (1830 mm), floor/bottom of appliance to highest top hinge/cover plane.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 perspective and side-profile drawings; also page 1 rows with hinges: 72 in (1830 mm), floor/bottom of appliance to highest top hinge/cover plane.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded
Page 2
Value used by ExactFit
25 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 side-profile and top-plan depth ladder: 25 in (635 mm), rear face of the fixed rear spacers to front of the case, excluding doors and handles.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 side-profile and top-plan depth ladder: 25 in (635 mm), rear face of the fixed rear spacers to front of the case, excluding doors and handles.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded
Page 2
Value used by ExactFit
28.75 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 side-profile and top-plan depth ladder; also page 1 no-handles row: 28 3/4 in (731 mm), rear face of the fixed rear spacers to front face of the closed doors.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 side-profile and top-plan depth ladder; also page 1 no-handles row: 28 3/4 in (731 mm), rear face of the fixed rear spacers to front face of the closed doors.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded
Page 2
Value used by ExactFit
31.125 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 top-plan depth ladder; also page 1 dimensions with hinges, handles and doors row: 31 1/8 in (790 mm), rear face of the fixed rear spacers to frontmost handle plane with doors closed.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 top-plan depth ladder; also page 1 dimensions with hinges, handles and doors row: 31 1/8 in (790 mm), rear face of the fixed rear spacers to frontmost handle plane with doors closed.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded
Page 2
Value used by ExactFit
43.375 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 open-door plan drawing: 43 3/8 in (1102 mm), rear face of the appliance/fixed-spacer envelope to forwardmost edge of a door at 90 degrees.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 open-door plan drawing: 43 3/8 in (1102 mm), rear face of the appliance/fixed-spacer envelope to forwardmost edge of a door at 90 degrees.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded
Page 2
Value used by ExactFit
36 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 lower installation-opening drawing; also 36 in on page 1: 36 in (914 mm), left inside face to right inside face of the installation opening.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 lower installation-opening drawing; also 36 in on page 1: 36 in (914 mm), left inside face to right inside face of the installation opening.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded
Page 2
Value used by ExactFit
72 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 lower installation-opening drawing; also page 1: 72 in (1830 mm), floor of opening to underside/top boundary of opening.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 lower installation-opening drawing; also page 1: 72 in (1830 mm), floor of opening to underside/top boundary of opening.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded
Page 2
Value used by ExactFit
25 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 lower installation-opening drawing and page 1 cutout footnote: 25 in (635 mm), rear inside wall of opening to front plane of the cabinet opening.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 lower installation-opening drawing and page 1 cutout footnote: 25 in (635 mm), rear inside wall of opening to front plane of the cabinet opening.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded
Page 2
Value used by ExactFit
0.125 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 top-plan cavity drawing: 1/8 in (3 mm), left side of appliance to left inside face of the cavity.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 top-plan cavity drawing: 1/8 in (3 mm), left side of appliance to left inside face of the cavity.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded
Page 2
Value used by ExactFit
0.125 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 top-plan cavity drawing: 1/8 in (3 mm), left side of appliance to left inside face of the cavity.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 top-plan cavity drawing: 1/8 in (3 mm), left side of appliance to left inside face of the cavity.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded
Page 2
Value used by ExactFit
0.5 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 ventilation note: 1/2 in (12.7 mm), top of the 71 1/2-inch cabinet to underside/top boundary of the opening.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 ventilation note: 1/2 in (12.7 mm), top of the 71 1/2-inch cabinet to underside/top boundary of the opening.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded
Page 2
Value used by ExactFit
1 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 ventilation note and top-plan cavity drawing: 1 in (25.4 mm), rear cabinet plane to rear wall/opening boundary behind the refrigerator.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 ventilation note and top-plan cavity drawing: 1 in (25.4 mm), rear cabinet plane to rear wall/opening boundary behind the refrigerator.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded
Page 2
Value used by ExactFit
3.6875 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
Installation Details door-swing plan: 3 11/16" (93) from the cabinet side to the handle with the left door at 90° (1 3/4" (45) to the door face). Owner decision 2026-10-17: the printed door projection past the cabinet side, handle included, is stored.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
Installation Details door-swing plan: 3 11/16" (93) from the cabinet side to the handle with the left door at 90° (1 3/4" (45) to the door face). Owner decision 2026-10-17: the printed door projection past the cabinet side, handle included, is stored.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded
Page 2
Value used by ExactFit
10.9375 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
Door-swing plan: 10 15/16" (278) from the cabinet side to the fully opened right door at 118°. Owner decision 2026-10-17: the printed door projection past the cabinet side, handle included, is stored.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
Door-swing plan: 10 15/16" (278) from the cabinet side to the fully opened right door at 118°. Owner decision 2026-10-17: the printed door projection past the cabinet side, handle included, is stored.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded
Page 2
Value used by ExactFit
35.625 in · Fit role: Informational only.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — web-d68866a8f2.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-17
page 2 installation-details perspective and plan drawings: 35 5/8 in (905 mm), outer left side of the case to outer right side of the case.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
page 2 installation-details perspective and plan drawings: 35 5/8 in (905 mm), outer left side of the case to outer right side of the case.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-10-17.
17 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°; Wall clearance for fully open door; Cabinet case width.
Availability: retained review record; original URL unavailable in the record.
Evidence reflects the sources reviewed on 2026-10-17. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
