This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-11-14. 1 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from; estimated values are not printed for this model and come from similar models of the same brand.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — 105163205.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-11-14
Exact-model appliance dimensions directly print closed width 35 5/8 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: "35 5/8" (905), closed appliance/case width. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p1) (D-2026-11-14-bosch-codex-fixes).
Exact-model appliance dimensions directly print closed width 35 5/8 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: "35 5/8" (905), closed appliance/case width. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p1) (D-2026-11-14-bosch-codex-fixes).
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — 105163205.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-11-14
Appliance dimensions without hinges and doors directly print height 71 1/2 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: "71 1/2" (1815), cabinet body height. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p1) (D-2026-11-14-bosch-codex-fixes).
Appliance dimensions without hinges and doors directly print height 71 1/2 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: "71 1/2" (1815), cabinet body height. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p1) (D-2026-11-14-bosch-codex-fixes).
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — 105163205.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-11-14
Appliance dimensions with hinges and doors directly print height 72 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: "72" (1830), highest door/hinge plane; "Add 5/8" with feet fully extended is a separate setting. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p1) (D-2026-11-14-bosch-codex-fixes).
Appliance dimensions with hinges and doors directly print height 72 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: "72" (1830), highest door/hinge plane; "Add 5/8" with feet fully extended is a separate setting. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p1) (D-2026-11-14-bosch-codex-fixes).
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — 105163205.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-11-14
Bosch B36CT80SNB installation details p.2: case depth **24" (610) with note "**Add 1" (25) for fixed spacers on back"; rule B (case-only depth includes fixed rear spacers) gives 25 in, as stored for B36CT80SNS. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; p.2 side elevation and plan: "25" (635), fixed-spacer rear plane to cabinet front; body alone "24" (610), "Add 1" (25) for fixed spacers on back". Both endpoints explicit; no additional rear gap on the 25-inch installed envelope.
Bosch B36CT80SNB installation details p.2: case depth **24" (610) with note "**Add 1" (25) for fixed spacers on back"; rule B (case-only depth includes fixed rear spacers) gives 25 in, as stored for B36CT80SNS. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; p.2 side elevation and plan: "25" (635), fixed-spacer rear plane to cabinet front; body alone "24" (610), "Add 1" (25) for fixed spacers on back". Both endpoints explicit; no additional rear gap on the 25-inch installed envelope.
Other evidence found
24 in — superseded
exactappliancefit.com; location not retained. Model scope: not separately recorded. Raw value: erall width : 35.625 in Height with hinge : 72 in Depth without door : 24 in Product dimensions describe named appliance endpo. The final reviewed registry supersedes this earlier audit value.
assets.skulytics.io; page 1. Model scope: not separately recorded. Raw value: Appliance dimensions without hinges and doors directly print depth 24 in.. The final reviewed registry supersedes this earlier audit value.
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — 105163205.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-11-14
Exact sheet directly prints appliance dimensions with hinges and doors, no handles, depth 28 3/4 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: closed depth "28 3/4" inches, table and side/plan endpoints agree. Recessed handles share the door-face endpoint; projecting handles have a separate endpoint. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p1) (D-2026-11-14-bosch-codex-fixes).
Exact sheet directly prints appliance dimensions with hinges and doors, no handles, depth 28 3/4 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: closed depth "28 3/4" inches, table and side/plan endpoints agree. Recessed handles share the door-face endpoint; projecting handles have a separate endpoint. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p1) (D-2026-11-14-bosch-codex-fixes).
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — 105163205.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-11-14
Exact-model dimensions: Depth 31 1/8 in; Depth without Handles 28 3/4 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: closed depth "31 1/8" inches, table and side/plan endpoints agree. Recessed handles share the door-face endpoint; projecting handles have a separate endpoint. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://www.ajmadison.com/cgi-bin/ajmadison/B36CT80SNB.html pNone) (D-2026-11-14-bosch-codex-fixes).
Exact-model dimensions: Depth 31 1/8 in; Depth without Handles 28 3/4 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: closed depth "31 1/8" inches, table and side/plan endpoints agree. Recessed handles share the door-face endpoint; projecting handles have a separate endpoint. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://www.ajmadison.com/cgi-bin/ajmadison/B36CT80SNB.html pNone) (D-2026-11-14-bosch-codex-fixes).
Other evidence found
28.5 in — superseded
www.designerappliances.com; location not retained. Model scope: not separately recorded. Raw value: Plain exact-model specification row: Depth = 28.5 in | Bottom Freezer - Black Stainless Steel ; Total Capacity: 21 Cu. Ft. ; Width: 35 5/8" ; Height: 72" ; Depth: 28 1/2". . The final reviewed registry supersedes this earlier audit value.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — 105163205.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-11-14
Exact-model 90/118-degree plan view directly labels the rear-to-front 90-degree envelope 43 3/8 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; p.2 door-swing plan: "43 3/8" (1102), rear plane to 90-degree open-door envelope. Source set to the local file Codex read: 105163205.pdf p2 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p2) (D-2026-11-14-bosch-codex-fixes).
Exact-model 90/118-degree plan view directly labels the rear-to-front 90-degree envelope 43 3/8 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; p.2 door-swing plan: "43 3/8" (1102), rear plane to 90-degree open-door envelope. Source set to the local file Codex read: 105163205.pdf p2 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p2) (D-2026-11-14-bosch-codex-fixes).
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — 105163205.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-11-14
Required cutout size directly prints width 36 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: "Required cutout size" = "72" x 36" x 25"" (H x W x D). Footnote: "The cutout depth of 25" includes the required 1" airflow." Printed opening governs. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p1) (D-2026-11-14-bosch-codex-fixes).
Required cutout size directly prints width 36 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: "Required cutout size" = "72" x 36" x 25"" (H x W x D). Footnote: "The cutout depth of 25" includes the required 1" airflow." Printed opening governs. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p1) (D-2026-11-14-bosch-codex-fixes).
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — 105163205.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-11-14
Required cutout size directly prints height 72 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: "Required cutout size" = "72" x 36" x 25"" (H x W x D). Footnote: "The cutout depth of 25" includes the required 1" airflow." Printed opening governs. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p1) (D-2026-11-14-bosch-codex-fixes).
Required cutout size directly prints height 72 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: "Required cutout size" = "72" x 36" x 25"" (H x W x D). Footnote: "The cutout depth of 25" includes the required 1" airflow." Printed opening governs. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p1) (D-2026-11-14-bosch-codex-fixes).
Other evidence found
72.5 in — superseded
Document 105163205.pdf; page 2. Model scope: not separately recorded. Raw value: 72 in standard appliance height plus documented 1/2 in top ventilation = 72 1/2 in opening.. The final reviewed registry supersedes this earlier audit value.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — 105163205.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-11-14
Required cutout size directly prints depth 25 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: "Required cutout size" = "72" x 36" x 25"" (H x W x D). Footnote: "The cutout depth of 25" includes the required 1" airflow." Printed opening governs. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p1) (D-2026-11-14-bosch-codex-fixes).
Required cutout size directly prints depth 25 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: "Required cutout size" = "72" x 36" x 25"" (H x W x D). Footnote: "The cutout depth of 25" includes the required 1" airflow." Printed opening governs. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p1) (D-2026-11-14-bosch-codex-fixes).
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
ExactFit estimate (Bosch doesn't print this for the model) ExactFit
Not printed for this model
Value used by ExactFit
0.125 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model.
Original published value and unit: see retained transcription below. Normalization: typical Bosch side gap (estimate)
Confidence label: low.
Primary evidence
ExactFit estimate (Bosch doesn't print this for the model) ExactFit · Estimate Model scope: Estimate from similar models Publication/revision date: Not recorded Location: Not printed for this model Reviewed: 2026-10-29
Not printed in the Bosch documents we have for this model. 1/8 in is the side gap Bosch prints for similar models (B36CL81ENG), so it is shown as an estimate. The fit check uses Bosch's cutout width for this model, so this estimate does not change the fit answer.
No document we have for this model prints this value.
Why this value was used
Not printed in the Bosch documents we have for this model. 1/8 in is the side gap Bosch prints for similar models (B36CL81ENG), so it is shown as an estimate. The fit check uses Bosch's cutout width for this model, so this estimate does not change the fit answer.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
ExactFit estimate (Bosch doesn't print this for the model) ExactFit
Not printed for this model
Value used by ExactFit
0.125 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model.
Original published value and unit: see retained transcription below. Normalization: typical Bosch side gap (estimate)
Confidence label: low.
Primary evidence
ExactFit estimate (Bosch doesn't print this for the model) ExactFit · Estimate Model scope: Estimate from similar models Publication/revision date: Not recorded Location: Not printed for this model Reviewed: 2026-10-29
Not printed in the Bosch documents we have for this model. 1/8 in is the side gap Bosch prints for similar models (B36CL81ENG), so it is shown as an estimate. The fit check uses Bosch's cutout width for this model, so this estimate does not change the fit answer.
No document we have for this model prints this value.
Why this value was used
Not printed in the Bosch documents we have for this model. 1/8 in is the side gap Bosch prints for similar models (B36CL81ENG), so it is shown as an estimate. The fit check uses Bosch's cutout width for this model, so this estimate does not change the fit answer.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — 105163205.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-11-14
Exact Bosch manual: leave 1/2 in gap at the top for proper ventilation. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; p.2: "Leave 1/2" (12.7) gap at the top and 1" (25.4) behind the refrigerator for proper ventilation." Top gap is above 71 1/2-inch case; 72-inch opening governs. Rear allowance is already in 25-inch cutout/fixed-spacer envelope.
Exact Bosch manual: leave 1/2 in gap at the top for proper ventilation. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; p.2: "Leave 1/2" (12.7) gap at the top and 1" (25.4) behind the refrigerator for proper ventilation." Top gap is above 71 1/2-inch case; 72-inch opening governs. Rear allowance is already in 25-inch cutout/fixed-spacer envelope.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — 105163205.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-11-14
Exact Bosch manual: leave 1 in behind for proper ventilation. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; p.2: "Leave 1/2" (12.7) gap at the top and 1" (25.4) behind the refrigerator for proper ventilation." Top gap is above 71 1/2-inch case; 72-inch opening governs. Rear allowance is already in 25-inch cutout/fixed-spacer envelope.
Exact Bosch manual: leave 1 in behind for proper ventilation. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; p.2: "Leave 1/2" (12.7) gap at the top and 1" (25.4) behind the refrigerator for proper ventilation." Top gap is above 71 1/2-inch case; 72-inch opening governs. Rear allowance is already in 25-inch cutout/fixed-spacer envelope.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — 105163205.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-11-14
105163205.pdf p2: "311/16 (93)" (page text checked 2026-11-14; Read on the page image by the Codex check 2026-11-14). Door figure = the printed 90-degree reach to the handle, 3 11/16 (93 mm) from the cabinet side on its own door-swing plan; the stored 1 3/4 reaches the door face only (larger printed, D-2026-11-07-door-swing-figures) (Bosch Codex check 2026-11-14, D-2026-11-14-bosch-codex-fixes). Was 1.75. Previous note: Exact-model Bosch installation details, top view with the doors open 90°: 1 3/4" (45 mm) beyond the cabinet side.
105163205.pdf p2: "311/16 (93)" (page text checked 2026-11-14; Read on the page image by the Codex check 2026-11-14). Door figure = the printed 90-degree reach to the handle, 3 11/16 (93 mm) from the cabinet side on its own door-swing plan; the stored 1 3/4 reaches the door face only (larger printed, D-2026-11-07-door-swing-figures) (Bosch Codex check 2026-11-14, D-2026-11-14-bosch-codex-fixes). Was 1.75. Previous note: Exact-model Bosch installation details, top view with the doors open 90°: 1 3/4" (45 mm) beyond the cabinet side.
Other evidence found
1.75 in — superseded
Document 105163205.pdf; page 2. Model scope: not separately recorded. Raw value: Exact-model Bosch installation details, top view with the doors open 90°: 1 3/4" (45 mm) beyond the cabinet side.. The final reviewed registry supersedes this earlier audit value.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded
No retained excerpt is available.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
No evidence decision recorded.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Bosch measurement source — 105163205.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-11-14
Appliance dimensions without hinges and doors directly print width 35 5/8 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: "35 5/8" (905), closed appliance/case width. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p1) (D-2026-11-14-bosch-codex-fixes).
Appliance dimensions without hinges and doors directly print width 35 5/8 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: "35 5/8" (905), closed appliance/case width. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p1) (D-2026-11-14-bosch-codex-fixes).
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Selected: 25 in. Earlier retained values: 24 in, 24 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Bosch B36CT80SNB installation details p.2: case depth **24" (610) with note "**Add 1" (25) for fixed spacers on back"; rule B (case-only depth includes fixed rear spacers) gives 25 in, as stored for B36CT80SNS. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; p.2 side elevation and plan: "25" (635), fixed-spacer rear plane to cabinet front; body alone "24" (610), "Add 1" (25) for fixed spacers on back". Both endpoints explicit; no additional rear gap on the 25-inch installed envelope.
Selected: 31.125 in. Earlier retained values: 28.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model dimensions: Depth 31 1/8 in; Depth without Handles 28 3/4 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: closed depth "31 1/8" inches, table and side/plan endpoints agree. Recessed handles share the door-face endpoint; projecting handles have a separate endpoint. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://www.ajmadison.com/cgi-bin/ajmadison/B36CT80SNB.html pNone) (D-2026-11-14-bosch-codex-fixes).
Selected: 72 in. Earlier retained values: 72.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Required cutout size directly prints height 72 in. Read on the page image by the Codex check 2026-11-14 (codex-work/bosch-accuracy, models-02: PASS; owner 2026-11-09 "Yes, record them", D-2026-11-09-codex-pass-reading): 105163205.pdf; pp.1-2: "Required cutout size" = "72" x 36" x 25"" (H x W x D). Footnote: "The cutout depth of 25" includes the required 1" airflow." Printed opening governs. Source set to the local file Codex read: 105163205.pdf p1 (the number is in its page text; was https://assets.skulytics.io/assets/docs/B36CT80SNB-105163205.pdf p1) (D-2026-11-14-bosch-codex-fixes).
Selected: 3.6875 in. Earlier retained values: 1.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
105163205.pdf p2: "311/16 (93)" (page text checked 2026-11-14; Read on the page image by the Codex check 2026-11-14). Door figure = the printed 90-degree reach to the handle, 3 11/16 (93 mm) from the cabinet side on its own door-swing plan; the stored 1 3/4 reaches the door face only (larger printed, D-2026-11-07-door-swing-figures) (Bosch Codex check 2026-11-14, D-2026-11-14-bosch-codex-fixes). Was 1.75. Previous note: Exact-model Bosch installation details, top view with the doors open 90°: 1 3/4" (45 mm) beyond the cabinet side.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Source documents and pages
Bosch measurement source — 105163205.pdf
assets.skulytics.io · Web source · secondary model/source
Model numbers covered: B36CT80SNB. Publication/revision date: Not recorded. Reviewed: 2026-11-14.
14 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Top clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-11-14. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.