This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Counter-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-25. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.625 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL81ENG-105167047.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL81ENG-105167047.pdf Appliance dimensions with hinges and doors (H x W x D) = 72 x 35 5/8 x 29 in.Open original source ↗ All retained supporting links
Why this value was usedAppliance dimensions with hinges and doors (H x W x D) = 72 x 35 5/8 x 29 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 71.5 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL81ENG-105167047.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit71.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL81ENG-105167047.pdf Appliance dimensions without hinges and doors (H x W x D) = 71 1/2 x 35 5/8 x 24 in.Open original source ↗ All retained supporting links
Why this value was usedAppliance dimensions without hinges and doors (H x W x D) = 71 1/2 x 35 5/8 x 24 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 72 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL81ENG-105167047.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit72 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL81ENG-105167047.pdf Appliance dimensions with hinges and doors (H x W x D) = 72 x 35 5/8 x 29 in.Open original source ↗ All retained supporting links
Why this value was usedAppliance dimensions with hinges and doors (H x W x D) = 72 x 35 5/8 x 29 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL81ENG-105167047.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL81ENG-105167047.pdf Appliance dimensions without hinges and doors (H x W x D) = 71 1/2 x 35 5/8 x 24 in.Open original source ↗ All retained supporting links
Why this value was usedAppliance dimensions without hinges and doors (H x W x D) = 71 1/2 x 35 5/8 x 24 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 29 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL81ENG-105167047.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit29 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL81ENG-105167047.pdf Exact model is explicitly described as Glass over Stainless Steel with Recessed Handles; appliance depth with hinges and doors is 29 in.Open original source ↗ All retained supporting links
Why this value was usedExact model is explicitly described as Glass over Stainless Steel with Recessed Handles; appliance depth with hinges and doors is 29 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 29 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL81ENG-105167047.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit29 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL81ENG-105167047.pdf Exact model uses recessed handles, so the directly printed 29 in appliance depth is also the handle-inclusive envelope.Open original source ↗ All retained supporting links
Why this value was usedExact model uses recessed handles, so the directly printed 29 in appliance depth is also the handle-inclusive envelope. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 43.375 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL81ENG-105167047.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit43.375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL81ENG-105167047.pdf Exact-model 90/118-degree plan view directly labels the rear-to-front envelope 43 3/8 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model 90/118-degree plan view directly labels the rear-to-front envelope 43 3/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL81ENG-105167047.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL81ENG-105167047.pdf Required cutout size (H x W x D) = 72 x 36 x 25 in.Open original source ↗ All retained supporting links
Why this value was usedRequired cutout size (H x W x D) = 72 x 36 x 25 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 72 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL81ENG-105167047.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit72 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL81ENG-105167047.pdf Required cutout size (H x W x D) = 72 x 36 x 25 in.Open original source ↗ All retained supporting links
Why this value was usedRequired cutout size (H x W x D) = 72 x 36 x 25 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL81ENG-105167047.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL81ENG-105167047.pdf Required cutout size (H x W x D) = 72 x 36 x 25 in.Open original source ↗ Why this value was usedRequired cutout size (H x W x D) = 72 x 36 x 25 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL81ENG-105167047.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL81ENG-105167047.pdf Exact-model cutout drawing directly labels 1/8 in at each side of the appliance.Open original source ↗ All retained supporting links
Why this value was usedExact-model cutout drawing directly labels 1/8 in at each side of the appliance. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL81ENG-105167047.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL81ENG-105167047.pdf Exact-model cutout drawing directly labels 1/8 in at each side of the appliance.Open original source ↗ All retained supporting links
Why this value was usedExact-model cutout drawing directly labels 1/8 in at each side of the appliance. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.5 in | ✓ Verified — retained secondary source | Bosch installation document — 105167047.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch installation document — 105167047.pdf Exact Bosch manual: leave 1/2 in gap at the top for proper ventilation.Open original source ↗ Why this value was usedExact Bosch manual: leave 1/2 in gap at the top for proper ventilation. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Verified — retained secondary source | Bosch installation document — 105167047.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch installation document — 105167047.pdf Exact Bosch manual: leave 1 in behind for proper ventilation.Open original source ↗ Why this value was usedExact Bosch manual: leave 1 in behind for proper ventilation. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 2 in | ? Verified — finalized database measurement | Bosch measurement source — 105167047.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit2 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — 105167047.pdf Exact-model Bosch installation details, top view with the doors open 90°: 2" (50 mm) beyond the cabinet side (9 5/8" at 118°). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedExact-model Bosch installation details, top view with the doors open 90°: 2" (50 mm) beyond the cabinet side (9 5/8" at 118°). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.625 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL81ENG-105167047.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL81ENG-105167047.pdf Appliance dimensions without hinges and doors (H x W x D) = 71 1/2 x 35 5/8 x 24 in.Open original source ↗ All retained supporting links
Why this value was usedAppliance dimensions without hinges and doors (H x W x D) = 71 1/2 x 35 5/8 x 24 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Web source · secondary model/source
Model numbers covered: B36CL81ENG. Publication/revision date: Not recorded. Reviewed: 2026-09-10.
13 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-10-25.
3 displayed measurements supported: Top clearance; Rear clearance; Wall clearance for door open to 90°.
Availability: retained review record; original URL unavailable in the record.
Evidence reflects the sources reviewed on 2026-10-25. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.