Measurement evidence for Bosch B36CL80SNS

Value used by ExactFit

35.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — MCDOC03224077-spec-sheet-2024-11.pdf
Bosch · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Appliance dimensions with hinges, handles and doors (H x W x D) 72"* x 35 5/8" x 31 1/8"
Reviewed: 2026-09-09

Appliance dimensions with hinges, handles and doors (H x W x D) 72"* x 35 5/8" x 31 1/8"

Why this value was used

Appliance dimensions with hinges, handles and doors (H x W x D) 72"* x 35 5/8" x 31 1/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

71.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — MCDOC03224077-spec-sheet-2024-11.pdf
Bosch · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Appliance dimensions without hinges and doors (H x W x D) 71 1/2" x 35 5/8" x 24"**
Reviewed: 2026-09-09

Appliance dimensions without hinges and doors (H x W x D) 71 1/2" x 35 5/8" x 24"**

Why this value was used

Appliance dimensions without hinges and doors (H x W x D) 71 1/2" x 35 5/8" x 24"**

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

72 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — MCDOC03224077-spec-sheet-2024-11.pdf
assets.skulytics.io · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Appliance dimensions with hinges, handles and doors (H x W x D) 72"* x 35 5/8" x 31 1/8"
Reviewed: 2026-09-09

Appliance dimensions with hinges, handles and doors (H x W x D) 72"* x 35 5/8" x 31 1/8"

Why this value was used

Appliance dimensions with hinges, handles and doors (H x W x D) 72"* x 35 5/8" x 31 1/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — MCDOC03224077-spec-sheet-2024-11.pdf
Bosch · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-24

Depth with the fixed rear spacers fitted, doors and handles excluded: 25 in. Rule B: case-only depth includes fixed rear spacers (owner decision 2026-09-16), as applied to Thermador T36FL810NS.

Why this value was used

Depth with the fixed rear spacers fitted, doors and handles excluded: 25 in. Rule B: case-only depth includes fixed rear spacers (owner decision 2026-09-16), as applied to Thermador T36FL810NS.

Other evidence found

• 24 in — superseded

  Document MCDOC03224077-spec-sheet-2024-11.pdf; location not retained. Model scope: not separately recorded. Raw value: Appliance dimensions without hinges and doors (H x W x D) 71 1/2" x 35 5/8" x 24"**. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — MCDOC03224077-spec-sheet-2024-11.pdf
Bosch · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Appliance dimensions with hinges and doors, no handles (H x W x D) 72"* x 35 5/8" x 28 3/4"
Reviewed: 2026-09-09

Appliance dimensions with hinges and doors, no handles (H x W x D) 72"* x 35 5/8" x 28 3/4"

Why this value was used

Appliance dimensions with hinges and doors, no handles (H x W x D) 72"* x 35 5/8" x 28 3/4"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

31.125 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — MCDOC03224077-spec-sheet-2024-11.pdf
Bosch · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Appliance dimensions with hinges, handles and doors (H x W x D) 72"* x 35 5/8" x 31 1/8"
Reviewed: 2026-09-09

Appliance dimensions with hinges, handles and doors (H x W x D) 72"* x 35 5/8" x 31 1/8"

Why this value was used

Appliance dimensions with hinges, handles and doors (H x W x D) 72"* x 35 5/8" x 31 1/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

43.375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — MCDOC03224077-spec-sheet-2024-11.pdf
Bosch · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-09

Exact-model plan view labels overall depth at 90 degrees as 43 3/8 in

Why this value was used

Exact-model plan view labels overall depth at 90 degrees as 43 3/8 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — MCDOC03224077-spec-sheet-2024-11.pdf
Bosch · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Required cutout size (H x W x D) 72" x 36" x 25"
Reviewed: 2026-09-09

Required cutout size (H x W x D) 72" x 36" x 25"

Why this value was used

Required cutout size (H x W x D) 72" x 36" x 25"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

72 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — MCDOC03224077-spec-sheet-2024-11.pdf
Bosch · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Required cutout size (H x W x D) 72" x 36" x 25"
Reviewed: 2026-09-09

Required cutout size (H x W x D) 72" x 36" x 25"

Why this value was used

Required cutout size (H x W x D) 72" x 36" x 25"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — MCDOC03224077-spec-sheet-2024-11.pdf
Bosch · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Required cutout size (H x W x D) 72" x 36" x 25"; The cutout depth of 25" includes the required 1" a
Reviewed: 2026-09-09

Required cutout size (H x W x D) 72" x 36" x 25"; The cutout depth of 25" includes the required 1" airflow.

Why this value was used

Required cutout size (H x W x D) 72" x 36" x 25"; The cutout depth of 25" includes the required 1" airflow.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — MCDOC03224077-spec-sheet-2024-11.pdf
Bosch · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-09

Exact-model opening drawing prints 1/8 in clearance at each side

Why this value was used

Exact-model opening drawing prints 1/8 in clearance at each side

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — MCDOC03224077-spec-sheet-2024-11.pdf
Bosch · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-09

Exact-model opening drawing prints 1/8 in clearance at each side

Why this value was used

Exact-model opening drawing prints 1/8 in clearance at each side

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — 105163236.pdf
assets.skulytics.io · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-09

Exact Bosch manual: leave 1/2 in gap at the top for proper ventilation.

Why this value was used

Exact Bosch manual: leave 1/2 in gap at the top for proper ventilation.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — 105163236.pdf
assets.skulytics.io · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-09

Exact Bosch manual: leave 1 in behind for proper ventilation.

Why this value was used

Exact Bosch manual: leave 1 in behind for proper ventilation.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — MCDOC03224077-spec-sheet-2024-11.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-27

Exact-model Bosch spec sheet, Installation Details top view: with the door open to 90 degrees it extends 1 3/4 in (45 mm) past the side of the case; at its full 118-degree opening, 3 11/16 in (93 mm).

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Exact-model Bosch spec sheet, Installation Details top view: with the door open to 90 degrees it extends 1 3/4 in (45 mm) past the side of the case; at its full 118-degree opening, 3 11/16 in (93 mm).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

3.6875 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — MCDOC03224077-spec-sheet-2024-11.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-27

Exact-model Bosch spec sheet, Installation Details top view: with the door open to 90 degrees it extends 1 3/4 in (45 mm) past the side of the case; at its full 118-degree opening, 3 11/16 in (93 mm).

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Exact-model Bosch spec sheet, Installation Details top view: with the door open to 90 degrees it extends 1 3/4 in (45 mm) past the side of the case; at its full 118-degree opening, 3 11/16 in (93 mm).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.625 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — MCDOC03224077-spec-sheet-2024-11.pdf
Bosch · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Appliance dimensions with hinges, handles and doors (H x W x D) 72"* x 35 5/8" x 31 1/8"
Reviewed: 2026-09-09

Appliance dimensions with hinges, handles and doors (H x W x D) 72"* x 35 5/8" x 31 1/8"

Why this value was used

Appliance dimensions with hinges, handles and doors (H x W x D) 72"* x 35 5/8" x 31 1/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.