This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Counter-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-29. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from; estimated values are not printed for this model and come from similar models of the same brand.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.625 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL80ENS-105163236.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL80ENS-105163236.pdf Exact-model appliance dimensions directly print closed width 35 5/8 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model appliance dimensions directly print closed width 35 5/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 71.5 in | ✓ Verified — retained secondary source | Bosch measurement source — original.pdf content.syndigo.com | Retained specification excerpt: Appliance dimensions without hinges and doors (H x W x D): 71 1/2" x 35 5/8" x 24". | |
Value used by ExactFit71.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — original.pdf Appliance dimensions without hinges and doors (H x W x D): 71 1/2" x 35 5/8" x 24".Open original source ↗ Why this value was usedAppliance dimensions without hinges and doors (H x W x D): 71 1/2" x 35 5/8" x 24". Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 72 in | ✓ Conflicting sources — resolved | Bosch measurement source — 105163236.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit72 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — 105163236.pdf Bosch lists 72 in standard overall height; 72 5/8 in is only with leveling legs fully extended.Open original source ↗ Why this value was usedBosch lists 72 in standard overall height; 72 5/8 in is only with leveling legs fully extended. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24 in | ✓ Verified — retained secondary source | Bosch measurement source — original.pdf content.syndigo.com | Retained specification excerpt: Appliance dimensions without hinges and doors (H x W x D): 71 1/2" x 35 5/8" x 24". | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — original.pdf Appliance dimensions without hinges and doors (H x W x D): 71 1/2" x 35 5/8" x 24".Open original source ↗ Why this value was usedAppliance dimensions without hinges and doors (H x W x D): 71 1/2" x 35 5/8" x 24". Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 28.75 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL80ENS-105163236.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit28.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL80ENS-105163236.pdf Exact sheet identifies recessed handles and prints appliance depth with hinges and doors as 28 3/4 in; no projecting handle is added.Open original source ↗ All retained supporting links
Why this value was usedExact sheet identifies recessed handles and prints appliance depth with hinges and doors as 28 3/4 in; no projecting handle is added. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 28.75 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL80ENS-105163236.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit28.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL80ENS-105163236.pdf Exact sheet identifies recessed handles; the directly printed 28 3/4 in appliance depth is therefore the handle-inclusive envelope.Open original source ↗ All retained supporting links
Why this value was usedExact sheet identifies recessed handles; the directly printed 28 3/4 in appliance depth is therefore the handle-inclusive envelope. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 43.375 in | ✓ Conflicting sources — resolved | Bosch measurement source — B36CL80ENS-105163236.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit43.375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL80ENS-105163236.pdf Exact-model 90/118-degree plan view directly labels the rear-to-front 90-degree envelope 43 3/8 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model 90/118-degree plan view directly labels the rear-to-front 90-degree envelope 43 3/8 in. Other evidence found
Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL80ENS-105163236.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL80ENS-105163236.pdf Required cutout size directly prints width 36 in.Open original source ↗ All retained supporting links
Why this value was usedRequired cutout size directly prints width 36 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 72 in | ✓ Conflicting sources — resolved | Bosch measurement source — B36CL80ENS-105163236.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit72 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL80ENS-105163236.pdf Required cutout size directly prints height 72 in.Open original source ↗ Why this value was usedRequired cutout size directly prints height 72 in. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL80ENS-105163236.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL80ENS-105163236.pdf Required cutout size directly prints depth 25 in.Open original source ↗ Why this value was usedRequired cutout size directly prints depth 25 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ≈ Estimated — not printed for this model | ExactFit estimate (Bosch doesn't print this for the model) ExactFit | Not printed for this model | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model. Original published value and unit: see retained transcription below. Normalization: typical Bosch side gap (estimate) Confidence label: low. Primary evidenceExactFit estimate (Bosch doesn't print this for the model) Not printed in the Bosch documents we have for this model. 1/8 in is the side gap Bosch prints for similar models (B36CL81ENG), so it is shown as an estimate. The fit check uses Bosch's cutout width for this model, so this estimate does not change the fit answer. No document we have for this model prints this value. Why this value was usedNot printed in the Bosch documents we have for this model. 1/8 in is the side gap Bosch prints for similar models (B36CL81ENG), so it is shown as an estimate. The fit check uses Bosch's cutout width for this model, so this estimate does not change the fit answer. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ≈ Estimated — not printed for this model | ExactFit estimate (Bosch doesn't print this for the model) ExactFit | Not printed for this model | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model. Original published value and unit: see retained transcription below. Normalization: typical Bosch side gap (estimate) Confidence label: low. Primary evidenceExactFit estimate (Bosch doesn't print this for the model) Not printed in the Bosch documents we have for this model. 1/8 in is the side gap Bosch prints for similar models (B36CL81ENG), so it is shown as an estimate. The fit check uses Bosch's cutout width for this model, so this estimate does not change the fit answer. No document we have for this model prints this value. Why this value was usedNot printed in the Bosch documents we have for this model. 1/8 in is the side gap Bosch prints for similar models (B36CL81ENG), so it is shown as an estimate. The fit check uses Bosch's cutout width for this model, so this estimate does not change the fit answer. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.5 in | ✓ Verified — retained secondary source | Bosch installation document — 105163236.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch installation document — 105163236.pdf Exact Bosch manual: leave 1/2 in gap at the top for proper ventilation.Open original source ↗ Why this value was usedExact Bosch manual: leave 1/2 in gap at the top for proper ventilation. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Verified — retained secondary source | Bosch installation document — 105163236.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch installation document — 105163236.pdf Exact Bosch manual: leave 1 in behind for proper ventilation.Open original source ↗ Why this value was usedExact Bosch manual: leave 1 in behind for proper ventilation. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 1.75 in | ? Verified — finalized database measurement | Bosch measurement source — 105163236.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit1.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — 105163236.pdf Exact-model Bosch installation details, top view with the doors open 90°: 1 3/4" (45 mm) beyond the cabinet side (9 7/16" at 118°). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedExact-model Bosch installation details, top view with the doors open 90°: 1 3/4" (45 mm) beyond the cabinet side (9 7/16" at 118°). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.625 in | ✓ Verified — retained secondary source | Bosch measurement source — B36CL80ENS-105163236.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit35.625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceBosch measurement source — B36CL80ENS-105163236.pdf Appliance dimensions without hinges and doors directly print width 35 5/8 in.Open original source ↗ All retained supporting links
Why this value was usedAppliance dimensions without hinges and doors directly print width 35 5/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 72 in. Earlier retained values: 72.625 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Bosch lists 72 in standard overall height; 72 5/8 in is only with leveling legs fully extended.
View source scope, location, and impact on fitSelected: 43.375 in. Earlier retained values: 43.38 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model 90/118-degree plan view directly labels the rear-to-front 90-degree envelope 43 3/8 in.
View source scope, location, and impact on fitSelected: 72 in. Earlier retained values: 72.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Required cutout size directly prints height 72 in.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Web source · secondary model/source
Model numbers covered: B36CL80ENS. Publication/revision date: Not recorded. Reviewed: 2026-09-10.
8 displayed measurements supported: Overall width; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗content.syndigo.com · Web source · secondary model/source
Model numbers covered: B36CL80ENS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
2 displayed measurements supported: Cabinet height; Depth without door.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-10-25.
4 displayed measurements supported: Height with hinge / controlling height; Top clearance; Rear clearance; Wall clearance for door open to 90°.
Availability: retained review record; original URL unavailable in the record.
Evidence reflects the sources reviewed on 2026-10-29. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.